Abstract
The fine manipulation of sound fields is critical in acoustics yet is restricted by the coupled amplitude and phase modulations in existing wave-steering metamaterials. Commonly, unavoidable losses make it difficult to control coupling, thereby limiting device performance. Here we show the possibility of tailoring the loss in metamaterials to realize fine control of sound in three-dimensional (3D) space. Quantitative studies on the parameter dependence of reflection amplitude and phase identify quasi-decoupled points in the structural parameter space, allowing arbitrary amplitude-phase combinations for reflected sound. We further demonstrate the significance of our approach for sound manipulation by producing self-bending beams, multifocal focusing, and a single-plane two-dimensional hologram, as well as a multi-plane 3D hologram with quality better than the previous phase-controlled approach. Our work provides a route for harnessing sound via engineering the loss, enabling promising device applications in acoustics and related fields.
Similar content being viewed by others
Introduction
The fine control of three-dimensional (3D) sound field presents a long-standing important question in acoustics, with the fundamental significance to a variety of applications ranging from ultrasound treatment and imaging to architectural acoustics to particle manipulation. The past few years have witnessed considerable efforts dedicated to researching the spatial control of sound, resulting in many methods that enable fascinating wave-steering effects by engineering the phase of transmitted/reflected waves1,2,3,4,5,6,7,8,9,10,11,12. Yet it is still challenging to achieve a complete control of sound that calls for totally independent modulation of all the two degrees of freedom, namely the amplitude and phase of sound, which collectively determine an arbitrary signal. Usually, complex coupling between amplitude and phase has to occur when the incident wave is interacting with sophisticated artificial structures, as evidenced by the fact that previous pure-phase metasurfaces generally ignore the error caused by the unavoidable variation in amplitude as the phase is adjusted3,4,5,6,7,8,9,10,11. Noting that the existing designs are mainly limited to lossless acoustic systems, it is of fundamental interest to explore the possibility to find new physics for sound manipulation by moving into a broader regime with loss of acoustic energy involved13,14,15,16,17,18,19,20. Given the conventional perspective that energy loss always destroys wave-steering capabilities and prevents effective downscaling of acoustic devices13,14, the presence of loss is expected to further complicate such coupling effect.
In this article, we prove, through analytical derivation, numerical simulation, and experimental demonstration, that it is possible to access the decoupled modulation of amplitude and phase of sound by deliberately introducing energy loss in a controlled manner15,16,17,18,19,20. A holey structured lossy acoustic metamaterial (LAM) is proposed to practically implement our design idea based on an inherently different mechanism from the previous ones3,4,5,6,7,8,9,10,11,12, which depend on either passive structures utilizing resonances to only delay the phase of sound or active elements requiring transducer arrays and complicated controlling circuits. The realization of decoupled tuning of amplitude and phase makes all combinations accessible in their full ranges (that is, [0,1] and [0,2π]), which is necessary for the manipulation of electromagnetic waves as pointed out in previous works on optical metasurfaces21,22.
By engineering the loss, our proposed mechanism endows the resulting device with the ability to realize the fine control of 3D sound fields, while bearing advantages of simple design, low-cost fabrication, planar profile, high efficiency, and deep-subwavelength resolution. We demonstrate this mechanism by producing some distinct phenomena, such as high-quality Airy beams, multifocal focusing, and both a single-plane two-dimensional (2D) hologram and a multi-plane 3D hologram that are conventionally subject to dramatic deterioration in both the quality and flexibility of the generated sound fields.
Results
Decoupled modulation of reflection amplitude and phase
Figure 1a shows the schematic of LAM comprising an array of unit cells, with predesigned geometries. Here we use absorbing boundaries at the back side to introduce energy loss into the acoustic metamaterial by totally absorbing the controlled leaky wave. The unit cells can modulate both amplitude and phase of reflection at the surface under the illumination of sound on the front side, as indicated by the red arrows in Fig. 1b, where the loss at the back side is required to control the reflection amplitude. As shown in Fig. 1c, each unit cell comprises three components: upper channel (C1), middle channel (C2), and lower channel (C3) with heights of h1, h2, and h3, respectively. The width of channels C1 and C3 is d = βD (β is defined as the filling ratio of air channel, D is the period of unit cells) and the width of channel C2 is w. The channel walls are assumed to be acoustically rigid. The total height of the unit cell is h = h1 + h2 + h3 with h2 fixed as h2 = 0.5 cm. In this study, the operating wavelength is denoted by λ, the period of unit cells D = λ/4 and the speed of sound in air c0 = 340 ms−1. Therefore, we obtain D = 0.5 cm for the chosen operating frequency f = 17 kHz. Due to the subwavelength nature of D, the amplitude A and phase ϕ of reflection are independent of the incidence direction.
Decoupled modulation of reflection amplitude and phase. a–c Schematic diagram of holey lossy metamaterials with an absorbing boundary at the back side in a, three-dimensional (3D) illustration in b and cross-section view of a unit cell in c are appended. d–g The coupling coefficients \(\overline M _{A(\phi ),h_1(w)}\) vs. h and β with decoupled points (DPs) and quasi-DPs marked by the crosses and arrows, respectively. h, i The reflection amplitude and phase responses to the parameters h1 and w for a unit cell operating at quasi-DPs. j, k The simulated and measured amplitude and phase vs. w and h1, respectively, which reveals that the reflection amplitude and phase are controlled by only one parameter, respectively. The simulations are carried out by the finite element solver in commercial software COMSOL MultiphysicsTM5.0
In general, A and ϕ are related to the structural parameters w and h1 of such a holey metamaterial22 (Supplementary Notes 1-3, Supplementary Figs. 1-2) and can be expressed as A = f1(w, h1) and ϕ = f2(w, h1), respectively, suggesting the ability to modulate A and ϕ by changing both w and h1. However, this is only the first step in accessing all the possible combinations of (A, ϕ). An intuitive way to ensure ergodicity in the phase-amplitude space is to make A and ϕ respectively controlled by one parameter, for example, A = f3(w) and ϕ = f4(h1), which, as will be revealed later, is enabled by reaching a decoupled point (DP) in the structural parameter space of LAM. In order to give quantitative evaluations of the dependence of reflection amplitude and phase on structural parameters, we define the coupling strengths as
We further obtain the coupling coefficients \(\overline M _{A(\phi ),h_1(w)}\) by integrating the coupling strengths for all combinations of (h1, w) and conducting normalization with respect to their maxima (Supplementary Note 4). As aforementioned, a completely decoupled manipulation of reflection amplitude and phase means that the amplitude and phase of reflection should be related to only one structural parameter (h1 or w). Here the filling ratio of air channel β is a crucial factor to influence \(\overline M _{A(\phi ),h_1(w)}\). For an extreme case of β = 1, which means the channel walls are infinitely thin, the amplitude A and phase ϕ can be analytically derived as (Supplementary Note 2)
Equations (2) and (3) clearly show the existence of completely decoupled relationships characterized by \(\overline M _{A,h_1} = 0\) and \(\overline M _{\phi ,w} = 0\), respectively, which correspond to DPs for \(\overline M _{A(\phi ),h_1(w)}\). In practice, we can simply access the DPs by bringing β close to 1. However, we cannot physically reach them due to the fact that very thin channel walls are flexible and no longer provide a rigid boundary (note that the rigidity of channel walls is the prerequisite condition of all our derivations), and mathematically the whole LAM is transformed into a trivial structure of purely air at β = 1. When β < 1, the analytical expressions of A and ϕ become quite complicated (Supplementary Note 3). We can still access quasi-decoupling domains, where near-zero coupling coefficients are achievable by setting the parameter h at specific values, which corresponds to quasi-DPs in the structural parameter space. The analytical calculations of \(\overline M _{A(\phi ),h_1(w)}\) vs. structural parameters (β, h) are shown in Fig. 1b. At the DPs where β = 1, as marked by the cyan crosses, \(\overline M _{A,h_1}\) and \(\overline M _{\phi ,w}\) are both exactly 0. When β < 1, the quasi-decoupling condition would occur at some discrete h values, for example, h = nλ/2 (n = 2, 3, 4,…). Apparently, the quasi-decoupling condition corresponds to the occurrence of Fabry–Pérot resonances.
In consideration of the sample fabrication, we set β = 0.8 and h = 2 cm to achieve the quasi-decoupling condition, as marked by the white circles in Fig. 1d–g. Figure 1h, i presents the correlation of A and ϕ to w and h1 at the quasi-DP, that is, (β, h) = (0.8, 2 cm). Figure 1j, k shows the simulated and measured phase and amplitude responses vs. w and h1 for the two cases of h1 = 0.75 cm and w = 0.2 cm, respectively. The results clearly demonstrate the decoupled tuning of A and ϕ within the ranges of [0, 1] and [0, 2π]. In the vicinity of quasi-DPs, our designed LAM benefits from the availability of all possible combinations of reflection amplitude and phase by tuning two separate geometric parameters (h1 and w) that induce a controlled leaky loss dependent on structural parameters.
It should be pointed out that the energy loss due to thermal viscosity in narrow channels is lower than 1% for each unit cell, since the cross-section of air channels is not deep subwavelength. Therefore, the boundary layer effect can be ignored in the manipulation of reflection amplitude and phase13,14. Such a significant feature of independent control of reflection amplitude and phase enables a complete manipulation of sound in 3D space.
High-fidelity acoustic hologram
First, we show the fine control of acoustic waves by hologram projection of complicated patterns. In analogy to the optical hologram23,24,25, the acoustic hologram projection was only recently reported, which offers new capabilities in particle manipulation and improvement in applications, such as ultrasonic treatment26,27,28. However, due to the lack of capability to modulate both amplitude and phase, the current production of acoustic holograms has to rely on phase-modulation (PM) approaches combined with a complex optimization process23,24,25,26,27,28,29. Here, we numerically and experimentally show that with decoupled amplitude phase modulation (APM), high-fidelity acoustic hologram can be stably generated without complex optimization process.
Consider the general principle for acoustic hologram reconstruction as illustrated in Fig. 2a. By discretizing the holographic image into a collection of subwavelength image pixels, the acoustic pressure p j with amplitude A j and phase ϕ j on the hologram plane (that is, the surface of LAM) can be calculated by superposing the wave components from those image pixels on the image plane, as follows
where k0 is the wave number, N is the total number of image pixels, A0l and ϕ0l are the amplitude and initial phase of the lth image pixel at (x l , y l , z l ), \(r_l = \sqrt {(x_j - x_l)^2 + ({\it{y}}_j - {\it{y}}_l)^2 + {\it{z}}_l^2}\) is the distance between the image pixel and the hologram pixel at (x j , y j , 0), A j and ϕ j are the amplitude and phase of jth hologram pixel on the hologram plane, respectively. It is straightforward to project the predesigned acoustic hologram due to time-reversal symmetry. The holographic image can thus be characterized by
where n is the total number of hologram pixels, \(r_j = \sqrt {(x - x_j)^2 + ({\it{y}} - {\it{y}}_j)^2 + {\it{z}}^2}\) is the distance between the spatial point at (x, y, z) and the hologram pixel at (x j , y j , 0) in the hologram plane. However, the previous schemes for producing acoustic holograms assume A j = 1 and the holographic image is then characterized by
High-fidelity acoustic hologram. a Schematic diagram of hologram reconstruction. b Schematic diagram of how the lossy acoustic metamaterial (LAM) projects high-quality acoustic hologram in simulation and experiment. c The target image of Nanjing University logo with complex amplitude distributions. Scale bar, 20 cm. d The simulated holographic image by the amplitude-phase-modulation (APM) method. e The simulated holographic image by the phase-modulation (PM) method. Permissions for use of the Nanjing University logo in this figure were obtained from Nanjing University. All rights reserved
Consequently an optimizing algorithm is needed to generate the target phase \(\phi {\prime}_j\) for active phased arrays29 or pure-modulation masks26,27. However, we point out that even for a very simple target image, the optimized hologram amplitude A j is an inhomogeneous distribution ranging from 0 to 1. Thus, it is important to introduce independent modulations of amplitude and phase, which is straightforward by controlling (A j , ϕ j ) at the hologram plane to generate (A0l, ϕ0l) at the image plane. Here, the reflection direction is normal to the hologram plane, as shown in Fig. 2b. Our method allows for the production of arbitrarily complex holographic images, such as those with continuously changing gray values, which may be impossible for previous methods that only engineer the phase of sound.
In order to show the superiority of independent APM, we have chosen a complicated predesign image for numerical investigation. The target image is the pattern of a school badge in Fig. 2c. We record the phase and amplitude information independently into the hologram plane for projecting the image. In Fig. 2d, the numerical result at the image plane shows that the holographic image is of high-quality compared with the target one. For previous PM methods26,27,28, the complexity of phase optimization and the quality of holograms are determined by the fineness of target images. Here, we append the holographic image simulated by the PM optimization of Gerchberg–Saxton algorithm in Fig. 2e. Comparing Fig. 2d, e, our APM method outperforms the PM method; in light of time-reversal symmetry it is necessary to modulate both the reflection amplitude and phase for achieving an exact hologram reconstruction of a complex image. We also note that in Fig. 2e, the image error caused by a uniform amplitude distribution on the hologram plane becomes quite prominent when the target image is complicated and comprises a large number of pixels with uneven amplitude levels.
The result demonstrates the effectiveness and flexibility of our method in complicated hologram reconstruction. Simulations for a more complicated hologram are provided in Supplementary Fig. 3 to further reveal the advantage of the APM method. In simulations, the number of pixels in the hologram plane for projecting the hologram in Fig. 2d is 359 × 359, which is a very large value. Yet the success of our proposed scheme in generating high-fidelity acoustic holograms is by no means a limit of its potential application. The engineering of loss is indeed significant for controlling sound fields at will and may have applications in varied scenarios. As typical examples, we will further show the production of the Airy beam, multifocal focusing, and both a single-plane 2D hologram and a multi-plane 3D hologram via holey structured LAMs in the following.
High-quality Airy beam and multifocal focusing
Next, we employ a LAM to generate an Airy beam based on the method of APM, in comparison with the one formed by the PM method30,31. Figure 3a, b shows the reflection amplitude and phase profiles on the surface of the LAM (along the x direction) required for generating a high-quality Airy beam. The spatial distribution of pressure amplitude follows an Airy function as shown in Fig. 3a, with the corresponding phase profile displayed in Fig. 3b30. Figure 3c, d provide the comparison of the projected sound-field distributions between the APM and PM methods, where it is apparent to the naked eyes that the Airy beam formed by APM has a better quality than the one formed by PM.
Formation of high-quality Airy beam. a, b Amplitude profile in a and phase profile in b at the surface of the LAM for generating the Airy beam. The LAM consists of 80 discrete unit cells (triangles). c, d Simulated pressure fields of Airy beams produced by the APM in c and PM in d. Scale bar, 10 cm. e, f Distributions of pressure amplitude on the dashed lines in c and d. The result for the perfect Airy beam is calculated by Eq. (7), which is displayed for comparison (red lines)
To quantitatively evaluate the quality of the generated beam, we also plot in Fig. 3e, f the distribution of pressure amplitude along the dashed lines in Fig. 3c, d, that is 5λ away from the sample surface. The result shows a good agreement between the Airy beam generated by APM and the ideal one calculated by32
where Ai(x j /a) is the Airy function, a is a constant, \(H_0^{(1)}\) is the zero-order Hankel function of the first kind. In comparison, a much larger deviation of the Airy beam generated by PM from the ideal one is observed in the right part of Fig. 3e, f. These results suggest that our design with the ability to yield decoupled manipulation of reflection amplitude and phase has the potential to improve the quality of non-diffraction beams as compared with the previous pure-phase method, such as using metasurfaces.
We have also quantitatively analyzed how APM helps to improve the quality of multifocal acoustic focusing in comparison with PM, where the size and number of unit cells of the two samples are 19.6 × 19.6 × 2 cm3 and 39 × 39, respectively. Both metamaterial samples are designed to generate a uniform multifocal focusing in an image plane parallel to and 20 cm away from the sample surface. The three focal points locate at (−6, 0 cm), (−2, 0 cm), and (6, 0 cm), respectively. Figure 4a shows the reflection amplitude and phase profiles at the surface of the LAM with the APM approach, which is calculated based on Eq. (4). The simulated acoustic pressure fields for APM and PM are shown in Fig. 4b, c, respectively. Figure 4d shows the pressure amplitude distribution curves along the dashed lines penetrating all three preset foci, as denoted in Fig. 4b, c, where the triangles mark the values at the three target focal points. Our numerical results clearly reveal that the APM method can produce highly uniform sound intensity at the three focal points, agreeing well with the design. Comparatively, although the pure-phase method is good at mimicking a simple single-focus effect, the intensities of different foci generated by the PM method are subject to substantial fluctuations for the case of multiple focusing. These results evidence the significance of APM for the production of complex sound field that actually needs a precise control of not only the phase but also the pressure amplitude on the hologram plane.
Multifocal acoustic focusing. a Amplitude and phase profiles at the surface of the LAM for multifocal acoustic focusing. b Simulated multifocal acoustic focusing by the APM method. Scale bar, 3 cm. c Simulated multifocal acoustic focusing by the PM method. d Distributions of pressure amplitude on the dashed lines in b and c. Three target focal points are marked by triangles
Experiments of single-plane and multi-plane holograms
In this section, we choose a tree image (Fig. 5a) as our target object, comprising 200 × 200 image pixels. Figure 5b presents the reflection amplitude and phase profiles on the hologram plane for projecting the tree pattern in the far field. The calculations of amplitude and phase profiles are based on Eq. (4). In the experiment, we fabricated the LAM samples via 3D printing with precision of 0.1 mm. The experiments were carried out in an anechoic chamber to demonstrate the acoustic hologram projection. We record both amplitude and phase information into the LAM sample, where the sample size is 60 × 60 × 2 cm3 with 119 × 119 unit cells, as shown by the photo in Fig. 5c. The size of image area is 60 × 60 cm2, with a distance 20 cm away from the surface of LAM. Other experimental details can be found in the Methods section. Due to the size limitations in 3D printing, the pixel number of the target image in our experiment is less than the numerical investigations in Fig. 2.
Experimental verification of single-plane acoustic hologram. a The predesigned image of a tree. Scale bar, 10 cm. Rights for use of this image are from Dreamstime (www.dreamstime.com). All rights reserved. b Amplitude and phase profiles on the hologram plane for projecting the tree image. c The photograph of the 3D printed LAM sample. d, e The simulated holographic image by the APM method and the experimentally measured result. Scale bar, 10 cm. f The simulated holographic image by the PM method. g The correlation between the resulting image and the predesigned image at different frequencies from 13 to 20 kHz for APM, and at 17 kHz for PM. h The correlation between the resulting image and the predesigned image when the image plane locates at different distances. i The correlation between the resulting image and the predesigned image for different back impedances
We plot the simulated and measured intensity distributions on the image plane in Fig. 5d, e, respectively, showing a good agreement between numerical and experimental results of fine single-plane 2D hologram. Figure 5f shows the simulated result based on the PM method for comparison. For a quantitative evaluation of the quality of acoustic hologram, we introduce the parameter image correlation which has been commonly used for measuring the similarity between the numerical/experimental image and the target one33. The calculation of correlation can be referred to the Supplementary Note 5. A higher value of correlation denotes a better similarity between the generated holographic image and the target image, and only when the two images are completely identical can a unitary correlation be achieved.
For the simple pattern shown in Fig. 5a, the PM method leads to less obvious errors (as shown in Fig. 5f), since the amplitude distribution via the APM method on the hologram plane is relatively uniform (as shown in Fig. 5b). The improvement by APM (in Fig. 5d) is still evident by both the naked-eye visual effect and the quantitative evaluation of image correlation. Figure 5g shows the relation between image correlation and operation frequency. The results reveal that our designed LAM has a relatively broad operation bandwidth, with the best performance observed at 17 kHz, due to the low dispersion of the groove structure32. Since the quasi-DP locates at 17 kHz, the image correlation in simulation (experiment) reaches maximum of 0.880 (0.771). We also note that the holographic image based on APM in a broad frequency range (14–20 kHz, correlation >0.770) is better than the one of the PM method (17 kHz, correlation = 0.767). The simulated holographic images at different frequencies based on PM or APM are appended in the Supplementary Fig. 4.
Figure 5h plots the image correlation at different distances of holographic image planes. The effect for APM is better than that of PM, and the correlation slightly decreases with larger distances due to wave diffraction. Even though the small size of unit cells (~0.25λ) helps to generate continuous amplitude and phase profiles, the method does not allow breaking the resolution limit in the hologram plane. However, Fig. 5h points out that we can still achieve high fidelity when the image plane is set close to the sample surface. Moreover, we emphasize simultaneous control of reflection amplitude and phase can be achieved even when the back absorption is partial (Supplementary Fig. 5). In this case, we can also project holograms with relatively good correlations to the target image, as unveiled in Fig. 5i.
Last, we demonstrate an acoustic hologram at multiple planes, as schematically depicted at Fig. 6a, where the holographic images are designed to be letters “N,” “J,” and “U” at three different planes that are spacing 12, 16, and 20 cm away from the hologram plane. The size of holographic regions at image planes 1, 2, and 3 is 60 × 60 cm2, and the bottom left corners of those holographic regions locate at (0, 30 cm), (10, 0 cm) and (30, 20 cm) in the x–y plane. We record amplitude and phase distributions (Fig. 6b) into the LAM sample of 119 × 119 unit cells (Fig. 6c). By comparing the amplitude field patterns in simulations and experiments in Fig. 6d, e, we observe a good agreement. To be specific, the image correlations to the perfect cases of letters “N,” “J,” and “U” are 0.827(0.705), 0.867(0.771), and 0.858(0.776) for the results of simulations (experiments), respectively.
Experimental verification of multi-plane acoustic hologram. a The predesigned image of a multi-plane acoustic hologram (letters “N,” “J,” and “U” at different distances of 12, 16, and 20 cm). b Amplitude and phase profiles on the hologram plane for projecting the “N,” “J,” “U” images at multiple planes. c The photograph of the 3D printed LAM sample. d, e The simulated holographic images by the APM method and the corresponding experimentally measured results. The correlations are marked in the figure. The correlation between the resulting image and the predesigned image is appended below each sub-figure. Scale bar, 10 cm. Rights for use of the NJU font images in this figure are from Adobe Font Software License: https://www.fontspring.com/lic/ztxtzqqpzi. All rights reserved
Discussion
In summary, we have shown that by judiciously controlling the leaky loss in acoustic metamaterials, one can achieve the fine control of acoustic waves, by modulating both amplitude and phase of acoustic waves in a static, precise, and decoupled manner. To exhibit the powerful ability of LAM in wave manipulation, we report the numerical and experimental realization of high-fidelity acoustic holograms and demonstrate the production of arbitrarily complicated acoustic fields based on the new mechanism for achieving decoupled amplitude and phase distributions. We also show that our method significantly improves the quality of other kinds of spatial manipulation of sound fields over previous pure-phase methods. We envision that our findings on tailoring loss for harnessing sound fields will have various acoustic-wave-based applications. For example, the realization of complicated 3D holographic images23 can produce arbitrarily shaped focusing or spatial field patterns for the high-intensity focused ultrasound treatments34 that hitherto have to rely on the time-consuming scanning method, which is also intriguing for particle manipulation26,29, architectural acoustics32, and stereo sound-field reconstruction35, etc.
Methods
Sample fabrication and experiment measurement
All the samples are made of photosensitive resin, and are manufactured via 3D printing technique (SLA, 0.1 mm in precision). The experiment for measuring reflection amplitude and phase responses of different unit cells is performed in a commercial impedance tube system (Brüel&Kjær Impedance Measurement Tube for ASTM Type 4206A, Brüel&Kjær PULSE Multi-analyzer system Type 3560, and Brüel&Kjær Power Amplifier Type 2716, Supplementary Note 6, Supplementary Fig. 6). The experiments for acoustic holograms in Figs. 5e and 6d are performed in an anechoic chamber for reducing undesired sound reflection. In order to generate a plane wave, an 8-cm-radius loudspeaker driven by a multifunctional signal generator (RIGOL DG1022) is located in the far field, about 3 m away from the center of LAM sample. The measured region is set at the image plane with an area of 60 × 60 cm2. The leaky back of the sample is facing towards the sound-absorbing panels that are set 2 cm away from the sample, the same as the simulation case. The scanning of pressure amplitude fields is conducted by using a 1/4-inch-diameter Brüel&Kjær type-4961 microphone and Brüel&Kjær PULSE Type 3160.
Numerical simulation
3D numerical simulations are carried out by the finite element solver in commercial software COMSOL MultiphysicsTM5.0, using a high performance computing cluster. A full 3D geometry is used in the “Pressure Acoustics, Frequency Domain” module. Perfectly matched layers are imposed on the outer boundaries of simulation domains to prevent reflections36.
Data availability
The data that support the findings of this study are available from the corresponding author upon request.
References
Ma, G. & Sheng, P. Acoustic metamaterials: from local resonances to broad horizons. Sci. Adv. 2, e1501595 (2016).
Cummer, S. A., Christensen, J. & Alu, A. Controlling sound with acoustic metamaterials. Nat. Rev. Mater. 1, 16001 (2016).
Li, Y., Liang, B., Gu, Z., Zou, X. & Cheng, J. Reflected wavefront manipulation based on ultrathin planar acoustic metasurfaces. Sci. Rep. 3, 2546 (2013).
Zhao, J., Li, B., Chen, Z. & Qiu, C. Manipulating acoustic wavefront by inhomogeneous impedance and steerable extraordinary reflection. Sci. Rep. 3, 2537 (2013).
Xie, Y. et al. Wavefront modulation and subwavelength diffractive acoustics with an acoustic metasurface. Nat. Commun. 5, 5553 (2014).
Tang, K. et al. Anomalous refraction of airborne sound through ultrathin metasurfaces. Sci. Rep. 4, 6517 (2014).
Mei, J. & Wu, Y. Controllable transmission and total reflection through an impedance-matched acoustic metasurface. New J. Phys. 16, 123007 (2014).
Li, Y. et al. Experimental realization of full control of reflected waves with subwavelength acoustic metasurfaces. Phys. Rev. Appl. 2, 064002 (2014).
Li, Y., Jiang, X., Liang, B., Cheng, J. & Zhang, L. Metascreen-based acoustic passive phased array. Phys. Rev. Appl. 4, 024003 (2015).
Zhu, X. et al. Implementation of dispersion-free slow acoustic wave propagation and phase engineering with helical-structured metamaterials. Nat. Commun. 7, 11731 (2016).
Jiang, X., Li, Y., Liang, B., Cheng, J. & Zhang, L. Convert acoustic resonances to orbital angular momentum. Phys. Rev. Lett. 117, 034301 (2016).
Zhang, P. et al. Generation of acoustic self-bending and bottle beams by phase engineering. Nat. Commun. 5, 4316 (2014).
Ward, G. P. et al. Boundary-layer effects on acoustic transmission through narrow slit cavitites. Phys. Rev. Lett. 115, 044302 (2015).
Serra-Garcia, M. & Daraio, C. Visco-thermal effects in acoustic metamaterials: from total transmission to total reflection and high absorption. New J. Phys. 18, 033003 (2016).
Zhu, X., Ramezani, H., Shi, C., Zhu, J. & Zhang, X. PT-symmetric acoustics. Phys. Rev. X 4, 031042 (2014).
Fleury, R., Sounas, D. & Alu, A. An invisible acoustic sensor based on parity-time symmetry. Nat. Commun. 6, 5905 (2014).
Shi, C. et al. Accessing the exceptional points of parity-time symmetric acoustics. Nat. Commun. 7, 11110 (2016).
Ding, K., Ma, G., Xiao, M., Zhang, Z. & Chan, C. T. The emergence, coalescence and topological properties of multiple exceptional points and their experimental realization. Phys. Rev. X 6, 021007 (2016).
Christensen, J., Willatzen, M., Velasco, V. R. & Lu, M. Parity-time synthetic phononic media. Phys. Rev. Lett. 116, 207601 (2016).
Li, Y. et al. Tunable asymmetric transmission via lossy acoustic metasurfaces. Phys. Rev. Lett. 119, 035501 (2017).
Liu, L. et al. Broadband metasurfaces with simultaneous control of phase and amplitude. Adv. Mater. 26, 5031–5036 (2014).
Jia, S., Wan, X., Su, P., Zhao, Y. & Cui, T. Broadband metasurface for independent control of reflected amplitude and phase. AIP Adv. 6, 045024 (2016).
Huang, L. et al. Three-dimensional optical holography using a plasmonic metasurface. Nat. Commun. 4, 2808 (2013).
Chen, W. T. et al. High-efficiency broadband meta-hologram with polarization controlled dual images. Nano Lett. 14, 225–230 (2013).
Wen, D. et al. Helicity multiplexed broadband metasurface holograms. Nat. Commun. 6, 9241 (2015).
Melde, K., Mark, A. G., Qiu, T. & Fischer, P. Holograms for acoustics. Nature 537, 518–522 (2016).
Xie, Y. et al. Acoustic holographic rendering with two-dimensional metamaterial-based passive phased Array. Sci. Rep. 6, 35437 (2016).
Hertzberg, Y. & Navon, G. Bypassing absorbing objects in focused ultrasound using computer generated holographic technique. Med. Phys. 38, 6407–6415 (2011).
Marzo, A. et al. Holographic acoustic elements for manipulation of levitated objects. Nat. Commun. 6, 8661 (2015).
Lin., Z. et al. Acoustic non-diffracting Airy beam. J. Appl. Phys. 117, 104503 (2015).
Gao, H. et al. Acoustic focusing by symmetrical self-bending beams with phase modulations. Appl. Phys. Lett. 108, 073501 (2016).
Zhu, Y. et al. Dispersionless manipulation of reflected acoustic wavefront by subwavelength corrugated surface. Sci. Rep. 5, 10966 (2015).
Lewis, J. Fast template matching. Vision. Interface 95, 15–19 (1995).
Illing, R. et al. The safety and feasibility of extracorporeal high-intensity focused ultrasound (HIFU) for the treatment of liver and kidney tumours in a Western population. Br. J. Cancer 93, 890–895 (2005).
Boone, M. M., Verheijen, Edwin, N. G., Van, T. & Peter, F. Spatial sound-field reproduction by wave-field synthesis. J. Audio Eng. Soc. 43, 1003 (1995).
Kinsler, L. Fundamentals of Acoustic (Wiley, New York, 1982).
Acknowledgements
The authors appreciate fruitful discussions with Prof. Cheng-wei Qiu and Prof. Jensen Li. This work was supported by the National Key R&D Program of China, (grant no. 2017YFA0303700), National Natural Science Foundation of China (grant nos. 11634006, 81127901, 11674119, 11404125, and 11690030). Y.Z. is supported by the program A for Outstanding PhD candidate of Nanjing University.
Author information
Authors and Affiliations
Contributions
Y.Z., J.H., X.F., and J.Y. performed the theoretical simulations; Y.Z., J.H., and X.F. designed and carried out the experiments; Y.Z., X.Z., B.L., and J.C. wrote the manuscript; X.Z., B.L., and J.C. guided the research. All authors contributed to data analysis and discussions.
Corresponding authors
Ethics declarations
Competing interests
The authors declare no competing interests.
Additional information
Publisher's note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Electronic supplementary material
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons license and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Zhu, Y., Hu, J., Fan, X. et al. Fine manipulation of sound via lossy metamaterials with independent and arbitrary reflection amplitude and phase. Nat Commun 9, 1632 (2018). https://doi.org/10.1038/s41467-018-04103-0
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/s41467-018-04103-0
- Springer Nature Limited
This article is cited by
-
Wide field-of-hearing metalens for aberration-free sound capture
Nature Communications (2024)
-
Holographic direct sound printing
Nature Communications (2024)
-
Refined acoustic holography via nonlocal metasurfaces
Science China Physics, Mechanics & Astronomy (2024)
-
Janus acoustic metascreen with nonreciprocal and reconfigurable phase modulations
Nature Communications (2021)
-
Implementing fractional Fourier transform using SH0 wave computational metamaterials in space domain
Science China Technological Sciences (2021)