Abstract
The freezing of water typically proceeds through impurity-mediated heterogeneous nucleation. Although non-planar geometry generically exists on the surfaces of ice nucleation centres, its role in nucleation remains poorly understood. Here we show that an atomically sharp, concave wedge can further promote ice nucleation with special wedge geometries. Our molecular analysis shows that significant enhancements of ice nucleation can emerge both when the geometry of a wedge matches the ice lattice and when such lattice match does not exist. In particular, a 45° wedge is found to greatly enhance ice nucleation by facilitating the formation of special topological defects that consequently catalyse the growth of regular ice. Our study not only highlights the active role of defects in nucleation but also suggests that the traditional concept of lattice match between a nucleation centre and crystalline lattice should be extended to include a broader match with metastable, non-crystalline structural motifs.
Similar content being viewed by others
Introduction
Surface roughness has been known to promote nucleation. In fact, it is a common experimental practice to scratch surface, to induce nucleation on surface irregularities such as grooves and pits. The active role of these surface irregularities on nucleation, in particular for a concave cavity, is well described by the heterogeneous classical nucleation theory (CNT) through a simple geometric argument1: a concave cavity reduces the volume of critical nucleus further than a flat or a convex surface, thus favouring the nucleation of a new phase. By the same argument, the theory predicts that the nucleation barrier monotonically decreases as cavity becomes sharper, that is, with a smaller tip radius.
Although the theory works well for the nucleation of gas and liquid, crystallization of solids on rough surface is often found to exhibit much more complex behaviours. For example, ice nucleation is found to be significantly promoted by surface irregularities on hematite particles2 and BaF2 (111) surface3. Very recent studies also provide direct experimental evidences that the acute wedges of mica4 and surface defects of potassium-rich feldspars5,6 are effective nucleation sites for ice crystallization from vapour. In contrast, droplet freezing experiments show surface roughness has a negligible effect on ice nucleation on superhydrophobic surfaces7. Such insensitivity is also reported on silicon, glass and mica substrates8. Importantly, experiments also suggest that the role of surface roughness could be coupled with other factors such as surface chemistry9.
The complexity in the surface-irregularity-induced crystallization is primarily due to the crystalline nature of solids. If a rough surface disrupts the crystalline ordering of solids, the nucleation of solids may become unfavourable. For example, simulations show that atomically rough graphitic surface suppresses density layering of water and inhibits heterogeneous ice nucleation10. Similarly, if there exists a certain structural match between surface irregularity and the lattice of solids, crystallization may be significantly promoted. Indeed, molecular crystals are selectively crystallized along the line of wedges obtained through crystal cleavage11,12,13. Simulations further show that there exists an optimal wedge angle where the nucleation rate of Lennard–Jones crystal becomes orders of magnitude higher in groove than on flat surface14.
Here we investigate heterogeneous ice nucleation within an atomically sharp, concave wedge through forward flux sampling (FFS) method15 and the mW water model16. We find the enhancement of ice nucleation within a concave wedge relative to planar surface only occurs under special wedge geometries. When wedge structurally matches the orientations of specific ice lattice planes, it can greatly enhance not only ice nucleation rate but also the propensity of a specific ice structure, thus allowing potentially controlling polymorph selection of ice. Surprisingly, when wedge does not match ice lattice, we find it may also significantly promote ice nucleation, as in the 45° wedge. The unexpected rate enhancement is found attributed to the favourable formation of metastable topological defects upon geometrical constraints exerted by wedge. The non-ice-like structural units subsequently facilitate the growth of regular ice structure, thus accelerating ice crystallization.
Results
Ice nucleation rate
The atomically sharp wedge is created by joining two graphene planes at a contact line with a wedge angle β. The relative crystalline orientation of graphene sheets is insignificant, as our previous study17 show that the crystallinity of graphene plays no active role in heterogeneous ice nucleation with the original water–carbon interaction strength10. For simplicity, the two graphene planes are kept at the same crystalline orientation (see Methods for more details). A large wedge angle eventually turns a wedge into a flat surface, that is, β=180°, whereas a very sharp wedge leads to confinement that also shifts the phase diagram of ice18. Therefore, we confine our ice nucleation study within a range of β∈ (30°, 150°). Figure 1a shows the calculated ice nucleation rate as a function of wedge angle β on the basis of the mW water model16. Nearly for all the angle β investigated, the wedge produces a nucleation rate higher than that on a flat carbon surface. At the first glance, this appears consistent with CNT qualitatively. A closer examination, however, shows the fundamental difference between our simulation results and the CNT prediction. First, although nucleation is generally enhanced by a wedge, the calculated nucleation rates exhibit a non-monotonic dependence on wedge angle. In contrast, CNT predicts a simple reduction of nucleation barrier or an enhancement of nucleation rate with respect to a decreasing wedge angle β. Second, there exist wedge angles, for example, 30°, 60° and 135°, where the calculated ice nucleation rate becomes virtually indistinguishable from that on flat surface. Examination of these nucleation trajectories shows that at these angles, ice indeed nucleates in the planar region of the carbon wedge, far away from the contact line of the wedge. Therefore, ice nucleation proceeds in the same manner as it does on flat graphene, regardless of wedge geometry. The absence of rate enhancement at these angles suggests that an atomically sharp wedge does not always promote crystallization.
Calculated rate constant of heterogeneous ice nucleation within an atomically sharp wedge as a function of wedge angle β at (a) 230 K and (b) 240 K. The red lines indicate the heterogeneous ice nucleation rates (with statistical uncertainty) computed on the flat graphene plane at the corresponding temperatures22. All the nucleation rates are calculated based on FFS method, except for those obtained at 230 K for the 43°, 45° and 47° wedges, where spontaneous nucleation occurs frequently in direct MD simulations. In these cases, the nucleation rates are computed directly based on multiple direct MD shootings (see Methods for details). The statistical uncertainty of those nucleation rates calculated based on FFS is obtained by estimating both the variance in the binomial distribution of the number of configurations collected at each interface and the landscape variance in the starting configurations at each previous interface42. (c,d) Side view of the fully crystallized ice at 230 K within the 70° and the 45° wedges, respectively. (e) Zoom in of d, to highlight the topologically defective structure. Water molecules and carbon atoms are represented by blue and green, respectively.
As CNT does not provide a rational explanation of the simulation results, we examine the nature of rate enhancement at the other wedge angles. Figure 1a also shows that ice nucleation is in fact promoted significantly only when β is around three angles, namely, 45°, 70° and 110°. At 70° and 110°, we find that the rate enhancement originates from the structural compatibility between the wedge and cubic ice Ic. As graphene is known to promote the formation of the basal plane of hexagonal ice Ih10,17,19 (which is equivalent to the {111} plane of cubic ice Ic), and as the dihedral angle between two intersecting {111} planes is 70.52° (or 109.48°), the growth of unstrained cubic ice Ic thus fits the wedge geometry when β is near these angles. When β deviates from these angles, the nucleation of strained ice crystal must also overcome an additional strain cost, which leads to a decreasing nucleation rate. A similar behaviour has also been observed in the nucleation of Lennard–Jones particles14.
Enhanced ice nucleation through matching ice lattice
The enhancement at 70° and 110° can thus be understood in terms of the templating effect in a broader sense: when a nucleation agent is able to create an ordering compatible with the structure of a crystalline phase, it will then promote the nucleation of the corresponding phase; if the induced ordering could further match the crystalline structure at a higher degree, the nucleation efficiency of an agent can be even more enhanced17. Indeed, in carbon–water system, a single graphene plane induces layering within the interfacial water that matches the density profile of ice normal to the basal plane10,17,19,20. This one-dimensional density match alone leads to an enhancement of ice nucleation rate by 25 orders of magnitude at 240 K, from 1.67 × 10−7 m−3 s−1 for homogeneous ice nucleation21 to 9.34 × 1018 m−3 s−1 on graphene surface22. When adding the second graphene so that the structural match occurs in two dimensions simultaneously, as in the 70° wedge, ice nucleation rate is further promoted by another eight orders of magnitude, yielding 8.6 × 1026 m−3 s−1 at the same temperature. Similarly, adding the third dimensional match is then expected to continue boosting ice nucleation. To confirm this conjecture, we create a tetrahedral pyramid by adding the third graphene plane to the 70° wedge so that all three graphene planes now are able to match three intersecting {111} planes simultaneously. When filled with water inside, this tetrahedral pyramid wedge is found to lead to spontaneous ice crystallization within 2 ns in direct molecular dynamics (MD) simulation at 240 K. In fact, the nucleation efficiency for tetrahedral pyramid is so high that one has to raise the temperature significantly, to explicitly compute its ice nucleation rate by FFS method. At 250 K, the calculated nucleation rate 9.6 × 1030 m−3 s−1 for tetrahedral pyramid exceeds those on flat graphene and in bulk water at the same temperature (estimated on the basis of CNT22) by nearly 30 and 90 orders of magnitude, respectively.
The increasing degree of structural match through special surface geometry also leads to an interesting enhancement of polymorph selection for cubic ice Ic. Although scattered experimental observations suggested the existence of cubic ice23, the unambiguous evidence of the well-defined cubic ice has not been reported24. In fact, recent studies suggest that the commonly referred cubic ice is indeed the stacking disordered ice24,25,26. It has been shown that the ice freshly grown from either homogeneous nucleation21,27 or pre-existing hexagonal ice28 is always stacking disordered, with an overall cubicity within the range of 2/3 to 1/2, depending on growth temperature. As shown in Fig. 2, when ice crystallizes on flat graphene, it consists of randomly stacked ice layers, with an overall fraction of cubic ice of 54% at 230 K. This is also consistent with the cubicity obtained in homogeneous nucleation21. When ice crystallizes within the 70° wedge, the overall cubicity significantly increases to 82%, with only one stacking fault separating two pieces of well-defined Ic crystals. Remarkably, ice is found to crystallize into nearly pure Ic within the tetrahedral pyramid, with an overall cubicity of 91%. The enhanced polymorph selection of ice is a natural consequence of multi-dimensional structural match: a one-dimensional match of ice basal plane applies no constraint to the perpendicular stacking sequence, thus yielding a regular stacking-disordered ice. In contrast, a two- or three-dimensional match of intersecting ice basal plane aligns the ABCABC stacking that is unique in Ic, because neither the ABAB stacking in Ih nor the disordered stacking allows two ice basal planes to intersect at 70° (or 110°). Figure 2 indeed shows that the increasing degree of structural match not only enhances the overall cubicity, but also significantly decreases the distribution variance, suggesting multi-dimensional structural match can be an effective approach for polymorph selection of cubic ice. Although beyond a certain size cubic ice will turn into the normal hexagonal or stacking disordered structure24,25,26, the stability of the cubic structure can now be preserved over a reasonably large size range, with the assistance of this special geometry (see Supplementary Note 2 for our test on a larger tetrahedral pyramid).
Ice exhibits a wide range of cubicity when it crystallizes (a) on a flat graphene, (b) within a 70° wedge and (c) within a tetrahedral pyramid. For each panel, the top and middle rows show the three-dimensional and side views of a representative configuration for fully crystallized ice, respectively. Red and blue represent the hexagonal Ih and cubic Ic, respectively. The bottom row shows the calculated distribution of cubicity χc, along with the corresponding mean cubicity 〈χc〉, s.d. σχc and number of configurations N used for computing the distribution. Cubicity χc is defined as the fraction of Ic in ice I (see Supplementary Note 1 for more details).
Enhanced ice nucleation without matching ice lattice
If the rate enhancement at 70° and 110° can be well interpreted on the basis of lattice match, then the sharp increase in the calculated ice nucleation rate at β=45° appears rather intriguing, because neither {0001} in Ih nor {111} in Ic forms a dihedral angle of 45° with respect to another common lattice plane in either crystal. In fact, examination of the crystallized ice structure (Fig. 1d) shows that the first layers of ice on both wedge planes of the 45° wedge are indeed ice basal planes, that is, same as in the 70° wedge. Clearly, a mechanism other than lattice match is responsible for rate enhancement.
Visualization of the crystallized ice within the 45° wedge identifies a set of topological defects composed of coupled 5−7 ring structure, as shown in Fig. 1e. The coupled 5−7 ring structure resembles the 5+7 defect found in bulk ice29. As the 5+7 defect has a very long lifetime30 and plays a substantial role in mediating bulk melting of ice30,31, it is not entirely surprising that the 5−7 ring structure may also appear in the freezing of liquid water, because it can well be an intermediate state between liquid and solid. In fact, a similar structure does emerge in the direct molecular simulation of homogeneous ice nucleation based on the TIP4P water model32. It is then of interest to understand how this defect structure forms in the 45° wedge.
To answer this question, we examine the spontaneous crystallization trajectory within the 45° wedge, obtained at 230 K. As shown in Fig. 3a, the 45° wedge sees the frequent formation of a uniquely ordered structure at the wedge contact line, preceding the growth of regular ice lattice above it. This ordered structure can be regarded as the lateral repetition of a wedge-shape, non-ice-like building block, as shown in Fig. 3c. The wedge-shape core (WC) is composed of two six-membered rings that are connected by one hydrogen bond (HB) at the top and share two HBs at the bottom. The WC can be derived from the single diamond core (SDC), which is the building block of cubic ice Ic (Fig. 3g), through replacing the two HBs on top of SDC by one HB. Therefore, the WC is akin to the crystalline phase of ice, but also involves a small distortion relative to the perfect tetrahedral network. In fact, the WC core has been previously identified as a stable fragment in the topological analysis of HB network in deeply supercooled water33 and it is also found to form spontaneously in the 45° wedge when explicitly including HBs by employing an atomistic water model (see Supplementary Note 3).
(a) Supercooled water (blue) at 230 K within the 45° wedge (green). The spontaneous formation of an ordered structure (highlighted) near the wedge contact line eventually leads to ice crystallization. Side view of ice is shown in b. (c–e) Nucleation pathway of ice within the 45° wedge. As a comparison, the nucleation pathway within the 70° wedge is shown in g–i. (f,j) Side views of the defect complex (e) and cubic ice complex (i), respectively.
Because of geometric constraint, the single WC core can only grow in parallel to the wedge contact line, by attaching other WC cores side-by-side. This parallel growth leads to a double WC (Fig. 3d), which provides the growth site for another polyhedral fragment on its top. As shown in Fig. 3e, this polyhedral cage (6552) is composed of five 6-membered rings as the prism planes and two 5-membered rings as the basal planes. In particular, the two 6-membered rings at the top of the cage are structurally compatible with the hexagonal core of Ih and thus can serve as the anchoring point to grow regular hexagonal layers of ice parallel to graphene planes. As the growth of regular ice layers cannot geometrically fit the 45° wedge, pairs of 5−7 rings emerge to bridge the structure gap. Interestingly, the 5−7 topological defects are found to align themselves regularly, in analogy to a large-angle grain boundary (Fig. 1e).
Given the structural affinity between the WC and SDC, it is also of interest to compare the nucleation pathways of ice within the 70° wedge and the 45° wedge. As shown in Fig. 3g-j, the two nucleation pathways are indeed very similar at the early stage: both start with the formation of connected cores parallel to the wedge contact line. The difference is that in the 45° wedge, the filling of the second layer requires another topologically defective fragment, whereas in the 70° wedge, this can be achieved seamlessly by adding two intrinsic cubic ice building blocks on top. Interestingly, both pathways are found to be capable of strongly enhancing ice nucleation and they yield comparable nucleation rates at low temperature (Fig. 1a). Although an increasing temperature is found to gradually differentiate the two pathways, that is, the 45° wedge leads to a lower nucleation rate than the 70° wedge (Fig. 1b), both special geometries are still significantly more efficient than a flat surface for inducing ice formation (see Supplementary Fig. 4 and Supplementary Note 4).
Discussion
The fact that both wedges lead to enhanced ice nucleation highlights the role of topological defects in ice nucleation. In fact, very little is known about the role defects play in nucleation34. Although topological defects were indeed found in homogeneous ice nucleation21, current study explicitly shows that the formation of topological defects can directly promote ice nucleation. From a structural point of view, a topological defect can be viewed as an intermediate structure between liquid water and ice. It has been shown that water at low temperature is filled with stable topologically defective fragments with small distortions33. Therefore, in light of Ostwald step rule35, it is not unexpected that the initial ice nucleation at moderate or high supercooling could also proceed with the formation of these defects as precursors. This may provide additional pathways to ice crystallization from a random HB network in liquid. However, as ice I consists of unique building blocks36, in order for ice to grow, the topological defects must either transform themselves into ice cores directly (for example, by adding a HB to a WC, to become an SDC) or arrange themselves into a defect complex which is structurally compatible with the addition of regular ice cores. If an external medium could help facilitate the formation of such defect complexes through geometric constraint, just as in the 45° wedge, the nucleation of ice can be subsequently enhanced.
The enhanced ice nucleation within the 45° wedge can thus be rationalized by the following consideration: the geometrical constraint enforced by wedge tip significantly reduces the space that water molecules can explore and, if the motion of water molecules is restricted in a way compatible with a structural unit of ice, the crystallization of ice can be subsequently enhanced. This is equivalent to reducing the entropic part of the free energy barrier17,19. In this sense, all the enhancements of ice nucleation observed in this study, whether within the 45° wedge, 70°/110° wedge or tetrahedral pyramid, share the same thermodynamic rationale. The difference lies in the degree of such entropic barrier reduction, which depends on both the level of match (that is, zero-, one-, two- or three-dimensional) and the structure that is matched with.
Therefore, in essence, ice nucleation within the 45° wedge could be interpreted as a structural match at a two-dimensional level, albeit that instead of matching ice lattice directly, the wedge matches a topological defect complex, which in turn facilitates the growth of ice cores. Traditionally, the concept of structural match or templating effect in heterogeneous nucleation describes how well a nucleation centre is capable of inducing a structural ordering in liquid coherent with crystalline lattice. Our work suggests that this concept may be extended to include a broader structural match with non-crystalline units. An important implication for this extension is that when understanding or searching for a heterogeneous nucleation centre, the apparent lattice mismatch between a nucleation centre and the nucleus alone may not be used as a criterion to exclude a candidate from being an efficient nucleation centre. As there also exist a number of other metastable topological building blocks in liquid water, one would expect that some unconventional surface topography and structures could also lead to enhanced ice nucleation. Further studies are certainly needed to identify those structures and to understand their efficiency for inducing ice nucleation.
Methods
Molecular dynamics simulations
Our MD simulations employes the mW16 water model. The carbon–water interaction is represented by the two-body term of the mW model10. To create the configuration of water inside, we immerse the graphene wedge within a bulk water configuration and then remove water molecules outside the wedge. The configuration is relaxed to avoid any unphysical overlap of atoms and then equilibrated for 10 ns. Carbon atoms are frozen at the graphene lattice sites, thus their equations of motion are not integrated in our MD simulations. A periodic boundary condition is employed. The resulted simulation cell, as shown in Supplementary Fig. 1, typically involves about 4,500∼7,500 water molecules (with a volume of water of 134 nm3∼224 nm3), depending on the wedge angle β. The length of wedge contact line is 5.06 nm. The isothermal canonical ensemble (NVT) with a Nose-Hoover thermostat is employed throughout our simulations.
Calculation of nucleation rate by forward flux sampling
The nucleation rates of ice are computed by FFS15 when ice nucleation becomes too slow to occur in direct MD simulations. The FFS has been successfully employed to study ice nucleation using both mW model17,21,22,37,38 and atomistic water model36,39. In this approach, the nucleation trajectory is decomposed into a series of successive transitional segments on the basis of an order parameter λ. In the case of ice nucleation, such order parameter has been chosen and validated as the number of ice-like water molecules contained within the largest ice cluster21,22,40. The ice-like water molecule is numerically distinguished through the local order parameter q6 such that a water molecule is considered to be truly ice-like when q6>0.5 (ref. 21). In addition, the nearest neighbours of a truly ice-like water molecule is also considered as ice-like, to account for the interfacial layer separating ice and water. The rate constant R is then obtained by the product of initial flux rate , which measures how frequently the system escapes from the basin A (liquid) to reach the interface λ0, and the growth probability P(λB|λ0) that evaluates how likely a configuration at interface λ0 will eventually reach the basin B (solid). Under the framework of FFS, the typically small P(λB|λ0) is calculated through
, where P(λi|λi–1) is the crossing probability for which a trajectory starts from the interface λi–1 and ends on the interface λi. P(λi|λi–1) can be directly obtained through firing a large number of trial runs at the interface λi–1. More details of application of FFS in ice nucleation can be found in refs 21, 22.
Estimating nucleation rate for spontaneous crystallization
When crystallization becomes spontaneous in MD simulation, FFS is no longer needed to obtain crystallization trajectories. In such a case, nucleation rate can be obtained by firing multiple, independent MD shootings, through41:
![](http://media.springernature.com/lw312/springer-static/image/art%3A10.1038%2Fncomms15372/MediaObjects/41467_2017_Article_BFncomms15372_Equ1_HTML.gif)
where NC is the number of crystallizing trajectories, NNC is the number of non-crystallizing trajectories, τi is the induction time for the ith crystallizing trajectory, τj is the trajectory length (simulation time) for the jth non-crystallizing trajectory and V is the simulation volume. It is noted that heterogeneous nucleation rate should be measured by area (for nucleation on a surface) or length (for nucleation along a line). Here, a volume-based nucleation rate is used because it allows for a direct comparison between homogeneous and heterogeneous nucleation, and also because the volume of water is small and ice nucleation on wedge line or surface is strongly preferred.
Ice formation within the 43°, 45° and 47° wedges is found to be spontaneous within the order of 101 ns from direct MD at 230 K. Therefore, multiple MD shootings are fired to calculate the corresponding ice nucleation rates using equation (1). To ensure convergence, the calculated rates are cross-checked against different numbers of crystallizing trajectories NC and the differences are found to be within 3% of the obtained rates. The details of these calculations are listed in Supplementary Table 1.
Data availability
The data that support the findings of this study are available from the corresponding author upon reasonable request.
Additional information
How to cite this article: Bi, Y. et al. Enhanced heterogeneous ice nucleation by special surface geometry. Nat. Commun. 8, 15372 doi: 10.1038/ncomms15372 (2017).
Publisher’s note: Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
References
Turnbull, D. Kinetics of heterogeneous nucleation. J. Chem. Phys. 18, 198–203 (1950).
Hiranuma, N. et al. Influence of surface morphology on the immersion mode ice nucleation efficiency of hematite particles. Atmos. Chem. Phys. 14, 2315–2324 (2014).
Conrad, P., Ewing, G. E., Karlinsey, R. L. & Sadtchenko, V. Ice nucleation on BaF2(111). J. Chem. Phys. 122, 064709 (2005).
Campbell, J. M., Meldrum, F. C. & Christenson, H. K. Observing the formation of ice and organic crystals in active sites. Proc. Natl Acad. Sci. USA 114, 810–815 (2017).
Atkinson, J. D. et al. The importance of feldspar for ice nucleation by mineral dust in mixed-phase clouds. Nature 498, 355–358 (2013).
Kiselev, A. et al. Active sites in heterogeneous ice nucleation—the example of K-rich feldspars. Science 355, 367–371 (2017).
Heydari, G., Thormann, E., Järn, M., Tyrode, E. & Claesson, P. M. Hydrophobic surfaces: topography effects on wetting by supercooled water and freezing delay. J. Phys. Chem. C 117, 21752–21762 (2013).
Campbell, J. M., Meldrum, F. C. & Christenson, H. K. Is ice nucleation from supercooled water insensitive to surface roughness? J. Phys. Chem. C 119, 1164–1169 (2015).
Hao, P., Lv, C. & Zhang, X. Freezing of sessile water droplets on surfaces with various roughness and wettability. Appl. Phys. Lett. 104, 161609 (2014).
Lupi, L., Hudait, A. & Molinero, V. Heterogeneous Nucleation of Ice on Carbon Surfaces. J. Am. Chem. Soc. 136, 3156–3164 (2014).
Carter, P. W. & Ward, M. D. Topographically directed nucleation of organic crystals on molecular single-crystal substrates. J. Am. Chem. Soc. 115, 11521–11535 (1993).
Bonafede, S. J. & Ward, M. D. Selective nucleation and growth of an organic polymorph by ledge-directed epitaxy on a molecular crystal substrate. J. Am. Chem. Soc. 117, 7853–7861 (1995).
Mitchell, C. A., Yu, L. & Ward, M. D. Selective nucleation and discovery of organic polymorphs through epitaxy with single crystal substrates. J. Am. Chem. Soc. 123, 10830–10839 (2001).
Page, A. J. & Sear, R. P. Crystallization controlled by the geometry of a surface. J. Am. Chem. Soc. 131, 17550–17551 (2009).
Allen, R. J., Frenkel, D. & Wolde, P. R. T. Simulating rare events in equilibrium or nonequilibrium stochastic systems. J. Chem. Phys. 124, 024102 1–16 (2006).
Molinero, V. & Moore, E. B. Water modeled as an intermediate element between carbon and silicon. J. Phys. Chem. B 113, 4008–4016 (2009).
Bi, Y., Cabriolu, R. & Li, T. Heterogeneous ice nucleation controlled by the coupling of surface crystallinity and surface hydrophilicity. J. Phys. Chem. C 120, 1507–1514 (2016).
Limmer, D. T. & Chandler, D. Phase diagram of supercooled water confined to hydrophilic nanopores. J. Chem. Phys. 137, 044509 1–11 (2012).
Cox, S. J., Kathmann, S. M., Slater, B. & Michaelides, A. Molecular simulations of heterogeneous ice nucleation. II. Peeling back the layers. J. Chem. Phys. 142, 184705 (2015).
Lupi, L. & Molinero, V. Does hydrophilicity of carbon particles improve their ice nucleation ability? J. Phys. Chem. A 118, 7330–7337 (2014).
Li, T., Donadio, D., Russo, G. & Galli, G. Homogeneous ice nucleation from supercooled water. Phys. Chem. Chem. Phys. 13, 19807–19813 (2011).
Cabriolu, R. & Li, T. Ice nucleation on carbon surface supports the classical theory for heterogeneous nucleation. Phys. Rev. E 91, 052402 (2015).
Whalley, E. Cubic ice in nature. J. Phys. Chem. 87, 4174–4179 (1983).
Malkin, T. L. et al. Stacking disorder in ice I. Phys. Chem. Chem. Phys. 17, 60–76 (2014).
Malkin, T. L., Murray, B. J., Brukhno, A. V., Anwar, J. & Salzmann, C. G. Structure of ice crystallized from supercooled water. Proc. Natl Acad. Sci. USA 109, 1041–1045 (2012).
Kuhs, W. F., Sippel, C., Falenty, A. & Hansen, T. C. Extent and relevance of stacking disorder in ‘ice Ic’. Proc. Natl Acad. Sci. USA 109, 21259–21264 (2012).
Moore, E. B. & Molinero, V. Is it cubic? ice crystallization from deeply supercooled water. Phys. Chem. Chem. Phys. 13, 20008–20016 (2011).
Hudait, A., Qiu, S., Lupi, L. & Molinero, V. Free energy contributions and structural characterization of stacking disordered ices. Phys. Chem. Chem. Phys. 18, 9544–9553 (2016).
Grishina, N. & Buch, V. Structure and dynamics of orientational defects in ice I. J. Chem. Phys. 120, 5217 (2004).
Donadio, D., Raiteri, P. & Parrinello, M. Topological defects and bulk melting of hexagonal ice. J. Phys. Chem. B 109, 5421–5424 (2005).
Mochizuki, K., Matsumoto, M. & Ohmine, I. Defect pair separation as the controlling step in homogeneous ice melting. Nature 498, 350–354 (2013).
Matsumoto, M., Saito, S. & Ohmine, I. Molecular dynamics simulation of the ice nucleation and growth process leading to water freezing. Nature 416, 409–413 (2002).
Matsumoto, M., Baba, A. & Ohmine, I. Topological building blocks of hydrogen bond network in water. J. Chem. Phys. 127, 134504 (2007).
Sear, R. P. The non-classical nucleation of crystals: microscopic mechanisms and applications to molecular crystals, ice and calcium carbonate. Int. Mater. Rev. 57, 328–356 (2012).
Ostwald, W. The formation and changes of solids. Zeitschr. Phys. Chem. 22, 289–330 (1897).
Haji-Akbari, A. & Debenedetti, P. G. Direct calculation of ice homogeneous nucleation rate for a molecular model of water. Proc. Natl Acad. Sci. USA 112, 10582–10588 (2015).
Li, T., Donadio, D. & Galli, G. Ice nucleation at the nanoscale probes no man's land of water. Nat. Commun. 4, 1887 (2013).
Haji-Akbari, A., DeFever, R. S., Sarupria, S. & Debenedetti, P. G. Suppression of sub-surface freezing in free-standing thin films of a coarse-grained model of water. Phys. Chem. Chem. Phys. 16, 25916–25927 (2014).
Sosso, G. C., Li, T., Donadio, D., Tribello, G. A. & Michaelides, A. Microscopic mechanism and kinetics of ice formation at complex interfaces: zooming in on kaolinite. J. Phys. Chem. Lett. 7, 2350–2355 (2016).
Lupi, L., Peters, B. & Molinero, V. Pre-ordering of interfacial water in the pathway of heterogeneous ice nucleation does not lead to a two-step crystallization mechanism. J. Chem. Phys. 145, 211910 (2016).
Walsh, M. R. et al. Methane hydrate nucleation rates from molecular dynamics simulations: effects of aqueous methane concentration, interfacial curvature, and system size. J. Phys. Chem. C 115, 21241–21248 (2011).
Allen, R. J., Frenkel, D. & Wolde, P. R. T. Forward flux sampling-type schemes for simulating rare events: efficiency analysis. J. Chem. Phys. 124, 194111 1–17 (2006).
Acknowledgements
The work is supported by NSF through award CMMI-1537286. T.L. also thanks the Sloan Foundation through the Deep Carbon Observatory for supporting this work.
Author information
Authors and Affiliations
Contributions
T.L. conceived and designed the research project. Y.B. and T.L. performed and analysed the simulations. Y.B., B.C. and T.L. contributed to the interpretation of the results. Y.B. and T.L. wrote the paper.
Corresponding author
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Supplementary information
Supplementary Information
Supplementary Figures, Supplementary Table, Supplementary Notes and Supplementary References (PDF 1896 kb)
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Bi, Y., Cao, B. & Li, T. Enhanced heterogeneous ice nucleation by special surface geometry. Nat Commun 8, 15372 (2017). https://doi.org/10.1038/ncomms15372
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/ncomms15372
- Springer Nature Limited
This article is cited by
-
Revealing isochoric water nucleation: a visual study
Scientific Reports (2024)
-
Two-dimensional bilayer ice in coexistence with three-dimensional ice without confinement
Nature Communications (2024)
-
An energy-free strategy to elevate anti-icing performance of superhydrophobic materials through interfacial airflow manipulation
Nature Communications (2024)
-
Janus regulation of ice growth by hyperbranched polyglycerols generating dynamic hydrogen bonding
Nature Communications (2022)
-
Freezing of few nanometers water droplets
Nature Communications (2021)