Abstract
Polyurethane foam (P.U.) injection resin techniques have been widely used for slab crack repair, soil improvement, and structural crack repair over the past 20 years. In this study, numerical investigations were carried out to enhance the strength of both sand and clay soils via utilizing polyurethane foam as inclusion material. The investigation was conducted using ‘GeoStudio (SLOPE/W) 2D’ software to model 6 m high homogeneous slopes made of soft clay and medium sand with varying slope angles (25°, 30°, 35°) on same soil extended up to 9 m depth and with inclusion of polyurethane foam piles of varying diameter (0.5 m, 0.8 m), length (up to 10 m) and spacing (0.5 m, 1 m, 2 m) in the slope face. The numerical model was verified using experimental test results conducted by Hassona and Abdelnaeem (Physical and mechanical properties of polyurethane foam conditioned sand. MSc, Civil Engineering Department, Faculty of Engineering Minia University). The results revealed that, for slope angle, Ø = 30°, the factor of safety for clay soil increased when using polyurethane piles (diameter, 0.5 m and 10 m length) having spacing of two m, one m, half m, and when used as sheet piles, respectively. The factor of safety for clay soil increased significantly when using polyurethane piles (diameter, 0.8 m, and 10 m length) having spacing the same as before and as sheet piles having width of 0.5 and 0.8 m, respectively. Also, for medium dense sand soil, using polyurethane piles (diameter, 0.5 m and 10 m length) having spacing the same as before, and as sheet piles increased factor of safety much more than that for clay soil. In addition, for medium dense sand soil similar observation were noticed using polyurethane piles (diameter 0.8 m, and 10 m length) having spacing the same as before, and as sheet piles, respectively. In addition, the effects of slope angles also studied.
Similar content being viewed by others
Avoid common mistakes on your manuscript.
1 Introduction
Soil injection technology, which stabilizes the soil by employing an expanding polyurethane resin, is one treatment for building settling problems. The research [14] reports on the large-scale in-situ experiment that was conducted to investigate the effects of soil injection technology on the lifting of a concrete foundation and the soil stabilization (improving of the soil beneath the foundation) at different soil depths. The effects of adding polyurethane-resin for soil shear strength, settlement, deformation modulus, and unconfined compressive strength was investigated by Hassona and Abdelnaeem [6]. Polyurethane reduces settlement; whenever the void ratio is high, the polyurethane fills and expands inside; as a result, the drop in the settlement is high and requires a low injection ratio. The pressure needed to inject polyurethane into soil voids varies depending on how low or high they are, and how big they are. Polyurethane is injected horizontally in larger soil voids.
Bai et al. [2] studied the effect of polyurethane (PU) to protect and improve the soil slope. The results show that the addition of polymers to natural soil may greatly increase its resilience to rainfall and overland flow because treated specimens showed a marked decrease in soil erosion.
Lat et al. [9] examined the applicability and effectiveness of PU as a substitute technique for ground improvement projects. As closed-cell foam, PU is impervious to water, which prevents water from penetrating the soil below it and softens it and lowering its shear strength. To further reduce further settling, Polyurethane foam is a lightweight material. Sufficient overburden on the PU foam, anchorage, or an appropriate drainage system to counter the rising ground water table can all be used to manage the foam's uplift behavior.
Kumar et al. [7] studied the stabilizing effects of polyurethane foam on weak soil. They concluded that, strength of black cotton soil with liquid of polyurethane foam increases its strength. In addition, foam had been applied on and filled the soil gaps. Prior to any building, the (P.U.) foam injection techniques were intended to minimize differential settling in foundations.
Abdulrasool and Al-Wakel [1] studied the behavior of gypseous soil treated with polyurethane foam (PF). Next, using a CBR test, the effects of PF on the strength of this soil under the effect of static loading were assessed. Additionally, a theoretical method for the design and analysis was provided by a physical laboratory model of footings on both treated and untreated of collapsible soil.
Hassona and Abdelnaeem [5] conducted extensive experimental effort to examine the physical properties of polyurethane foam (P.U.). The behavior of polyurethane foam-impregnated sand in three different sites using a plate load test was examined. Also, an unconfined compression test on sand samples mixed with different proportions of polyurethane foam was studied. Each study's findings indicate that the addition of such material, when the sand is impregnated, significantly improves strength and reduces settlement.
An expanding polyurethane resin is used in the soil injection process, providing a unique opportunity to strengthen, improve and compensate for settlement in the foundations of already-existing buildings. According to Sabri et al. [15] the foundations and infrastructures, such as roads or aerodromes built on a particular soil are affected by the advent of such soil problems.
Polyurethane was employed by Tan et al. [16] to treat sand and clay slopes. Through rainfall modelling, unconfined compression, and direct shear testing, the treated slope's strength and erosion resistance were significantly improved.
Polyntsev and Kvitko [13] introduced a research to study the effect of using polyurethane binders in road construction is mainly aimed at strengthening slopes, recesses, bulk structures, cones of bridges and overpasses, the surface of which is strengthened by rubble or gravel, in order to protect them from external environmental factors.
According to Liu et al. [10] a large number of efforts have been focused on restoring inter-particle cohesiveness in order to increase topsoil stability, without sufficient consideration for ecological and environmental factors. Therefore, to prevent erosion and strengthen the top soil of a sandy slope, water-based polyurethane (PU) soil stabilizer is injected. An efficient and environmentally friendly substitute for topsoil stabilization on sandy slopes is PU treatment. The results indicated that within the approximate range of 30–40% is the most cost-effective and efficient PU concentration for soil strengthening.
In slope engineering, traditional reinforced concrete piles are strong and cheap, but their long maintenance period and slow forming make it hard to meet requirements of emergency work, including landslides brought on by rainfall. Wang et al. [17] examine the effect of a novel polymer anti-slide pile type on slope stability during rainfall. The results illustrated that when the intensity of the rainfall increases, the slope stability deteriorates.
Evaluating the strength increases of the polyurethane-treated sand-root composite and, consequently, examining the interactions between the polymer, the root, and the soil was examined by Liu et al. [11]. The strengthening effect is more effective with a higher polymer concentration, according to the results. The results showed that low root content had an unfavourable weakening influence on the treated soil's strength through variable vegetation root contents. Also, due to the special network structure of polymers, soil stability is significantly increased. This is because the roots' tensile strength may be fully mobilized due to the improved shear resistance at the root-soil interface.
Lightweight polyurethane (PU) foam is an effective ground improvement technique for addressing differential soil foundation settling, primarily for infrastructure such as roads, highways, and parking lots. The goal of the research is to investigate how soil uplift and settling interact using the technique of finite elements, overburden load change, and PU foam thickness [8].
Polyurethane columns can be used to increase the bearing capacity of marine clay, according to Yong et al. [19]. The results demonstrated that as the PU columns' length increased, increasing the marine clay's ultimate bearing capacity. At the end, bearing PU columns, a maximum improvement ratio of 220% was achieved.
In recent years, polyurethane polymer has become a popular material for emergency and disaster relief engineering because of its superior tensile qualities. For slope reinforcement, 3D multi-row polyurethane polymer micro anti-slide piles model which takes into account variations in embedded depth and pile placement has been developed. To investigate the viability and strengthening effect of employing small anti-slide piles made of polyurethane polymer to reinforce slopes [18].
In this paper, the effectiveness of medium-density sand and medium-clay slopes that was filled with polyurethane foam (P.U.) as soil piles was studied, the effect of employing various polyurethane foam pile dimensions on these slopes’ safety factor was investigated. In addition, the effect of the spacing between the (P.U.) foam piles used on improving slopes made of medium sand and medium clay soil was studied. Finally, authors have been considering the advantages of using this light material to improve slopes while taking into account a number of significant factors, including the length and diameter of polyurethane foam piles and the effect of the spacing between them on slopes composed of medium-density sand and medium-clay soil. The authors used numerical model (Geostudio program) which considered an important program in soil calculations, to simulate and analyse these cases as discussed in the current study. The constraints of this study: Boundary condition of the numerical program, this study focused on the pile, the pile subjected to axial force only, no bending moment allowed, and the stiffness and type of the support system.
2 Verification of GeoStudio finite element model using [12], and validation of soil model using the Alzey Bridge (after Engin et al. [4])
2.1 Model setup [12]
The problem is symmetric, so only one half is modelled (in this case the right half is chosen). The wide of embankment is 16.0 m high is 4.0 m. The slopes have an inclination of 1:3. The soil formation as shown in Fig. 1. The phreatic level is located 1 m below the original ground surface. Under the soft soil layers there is a dense sand layer of which 4.0 m are considered in the model as shown in Fig. 1, geotechnical properties of the soil layer are listed in Table 1.
Cross section of a road embankment (after PLAXIS 2D-Tutorial Manual [12])
2.2 Comparing theoretical and experimental results
Figure 2 shows the computed and measured compressive strength versus deformation. Both measured and numerical results were found to be in very good agreement. In general, there is high agreement between the computed and measured results as shown in Fig. 2. Hence, It can be employed this finite element program (GeoStudio) that follows in this investigation.
2.3 Validation of soil model using the Alzey Bridge (after Engin et al. [4])
Authors using the results of field model (Near Frankfurt, pile loading test of Alzey Bridge) to check the validity of using this program. Also, when examining new soil models. The Alzey Bridge pile load test is commonly used by researchers as an axially loaded validation. The soil formation and groundwater table as shown in Fig. 3. The pile length is 9.5 m and 1.3 m in diameter. The loads were added gradually and kept there until the rate of settling was negligible. Measurements were taken of the applied loads and the resulting displacements at the tested pile head. The soil and pile properties data are presented in Tables 2 and 3, which are taken from the study of Engin et al. [4].
Geometry of the pile load test of Alzey Bridge (after Engin et al. [4])
The pile load displacement behavior discovered using the GeoStudio software is contrasted with that derived from experimental results in Fig. 4. The load–displacement behavior of piles may be comparable between the findings of theoretical and field stress tests. As a result, the validity of the soil and pile GeoStudio modeling has been established.
3 Numerical simulation
3.1 Construction procedure of the slopes
Building well-built roads is not only economical but also safe and reduces environmental effects. A stable road's construction is, implicitly, a key element in achieving these objectives. Therefore, a well-built road must have stabilized cuts and fills. This covers the continuous stability of slopes with cut batter, constructed fill, and slopes close to river margins, culverts, bridge abutments, and waterways. The cut banks, ditches, road carriageway, berms, and fill slope are all part of the road structure that must be stable water control is an essential part of road stability. Slopes are typically less expensive to build than walls; therefore they are used to build stockpiles, highways, dams, levees, canals, and other structures. The following steps are used in the construction of the slopes and the polyurethane foam pile technique:
-
1.
Remove unsatisfactory material, using construction drawings as a guide, dig and compact appropriate bedding material to the appropriate heights in steps based on the elevation of separate soil lifts.
-
2.
Establish the reinforcement in accordance with construction drawings to ensure that it matches the design engineer's chosen orientation, elevation, and embedment. Polyurethane foam stacks, for example.
3.2 Using the GeoStudio 2018 program to establish the geometry of the 2D problem
In general, there is high agreement between the computed and measured results as shown in Fig. 3. Hence, It can be employed this finite element program (GeoStudio) that follows in this investigation. Also, the findings of theoretical and field stress tests as shown in Fig. 4. As a result, the validity of the soil and pile GeoStudio modeling has been established.
In the current study, GeoStudio (2D) program was employed to investigate the performance of medium dense sand and medium clay slopes when inclusions of polyurethane foam piles in slopes. The geometry of the numerical 2D model as shown in Figs. 5, 6, 7 and 8.
3.3 Boundary conditions and mesh generation
The program's structures mode is used to generate the structural elements. In this case, the modelled structures are (P.U.) foam piles with different diameters, different lengths, and different pile spacing's were adopted in medium dense sand and medium clay slopes. Boundary conditions were assigned as slip surface entry (left side) and exit range (right side) as shown in Fig. 7. When the geometry model using GeoStudio (SLOPE/W) finite element 2D program is completed, the finite element model can be generated. There are five mesh sizes available: medium, fine, very fine, coarse, and very coarse. In this study, to increase accuracy, a fine mesh size was used. The choice of mesh dimension depends on what accuracy of the results is required.
3.4 Material models parameters
The parameters taken in the present study are the density γ in kN/m3, cohesion c in kN/m2, and angle of internal friction Ø. The physical properties of the soil (medium dense sand and medium clay) as indicated in Table 4, these values are extracted from Bowles [3] and modelled in this study using Mohr–Coulomb Model. The characteristics listed in Table 5 were also used to model polyurethane foam piles. In the current study, the physical and mechanical properties of the polyurethane foam used in this investigation are given in Table 6 (after Hassona and Abdelnaeem [5]).
3.5 Model test series
One hundred sixty-two (162) numbers of test runs are conducted as indicated in Table 7 for slope angle 30°. In addition, eighty-four (84) cases were carried out on piles diameter = 0.5 m, piles length = 1.0–10 m, pile spacing = 0.5 m and sheet piles, using slope angle 25° and 35° to study the effect of slope angle for medium dense sand and medium clay on the value of factor of safety.
4 Results and discussion
4.1 Introduction
Polyurethane foam piles having diameters of D = 0.5 m and 0.8 m were modelled in medium dense sand and medium clay soil, respectively. The piles length was changed from 1.0 to 10 m. Also, the spacing between these piles was changed between half, one, two meter, and sheet piles. There are many slip surface diagram for each case as shown in Fig. 9. The critical slip surface diagram generated in Geostudio software as shown in Fig. 10 for case of medium clay (pile diameter = 0.8 m, pile spacing = 2.0 m, and pile length = 10 m as an example). The values of factor of safety (F.O.S.) for each case were calculated and the percentage increases in each value were discussed for all cases as indicated in the following sections.
4.2 Effect of polyurethane foam piles
4.2.1 Medium-stiff cay having 30° slope angle
Figure 11 illustrate the relationship between factor of safety and piles length for medium-stiff clay slope having 30° slope angle, having pile spacing 2.0 m, 1.0 m, 0.5 m, and sheet piles, respectively. The factor of safety increases with the increasing of length and diameter of polyurethane foam piles. The results show that the value of the factor of safety is constant without change until the length of the pile is about 8 m, after which there is an increase in the factor of safety because the critical slip surface does not pass through the pile until 8 m, and after that the critical slip surface cuts the pile, causing an increase in the factor of safety as shown in Figs. 12 and 13.
4.3 Effect of polyurethane foam piles length
4.3.1 Medium dense sand having 30° slope angle
Using Polyurethane foam piles increases the F.O.S. for medium dense sand having 30° slope angle. Figure 14 shows the relation between factor of safety and piles length for medium dense sand having 30° slope angle, with pile spacing 2.0 m, 1.0 m, 0.5 m, and sheet piles, respectively. The findings indicate that the factor of safety keeps constant up to a length of approximately 3 m. Above that point, an increase in the F.O.S. occurs as a result of the critical slip surface cutting through the pile; as shown in Figs. 15 and 16.
4.4 Effect of polyurethane foam piles spacing's
4.4.1 Medium-stiff cay having 30° slope angle
Figures 17 and 18 show the relationship between Polyurethane foam piles spacing's and factor of safety (F.O.S) for medium clay having 30° slope angle. The result indicated that factor of safety increased as the piles spacing's decreased. Based on the results, it can be noted that the factor of safety remains constant up to a length of approximately 8 m. Above that point, an increase in the factor of safety occurs as a result of the critical slip surface cutting through the pile, which raises the factor of safety. Also, the percentage increase in F.O.S. and (L/D) ratio as shown in Figs. 19 and 20.
4.5 Effect of polyurethane foam piles spacing's
4.5.1 Medium dense sand having 30° slope angle
Again, the same results were obtained using Polyurethane foam piles with different lengths embedded in medium dense sand. Figures 21 and 22 show the relationship of Polyurethane foam piles spacing's and factor of safety (F.O.S) for medium dense sand having 30° slope angle. The results show that the value of the factor of safety is constant without change until the length of the pile is about 3 m, after which there is an increase in the F.O.S. because the critical slip surface does not pass through the pile until 3 m, and after that the critical slip surface cuts the pile, causing an increase in the F.O.S.
4.6 Effect of polyurethane foam piles spacing's on the percentage increase in factor of safety (F.O.S)
4.6.1 Medium dense sand having 30° slope angle
Also, the percentage increase in F.O.S. and (L/D) ratio as shown in Figs. 23 and 24. The critical slip surface cuts the pile, causing an increase in the factor of safety.
4.7 Effect of slope angle on medium clay slope factor of safety (F.O.S.)
As mentioned before, numerical models were built with different slope angles 25º and 35º, polyurethane foam piles having variables lengths embedded in the medium clay, and having the same pile diameter 0.5 m to study the effect of slope angle on factor of safety (F.O.S). Figures 25, 26, 27, and 28 illustrate that increasing the slope angles decreased the (F.O.S.).
4.8 Influence of slope angle on medium clay slope factor of safety (F.O.S.) percentage
Figures 29, 30, 31, and 32 show the percentage increase in F.O.S. and (L/D) ratio. The critical slip surface cuts the pile, causing an increase in the factor of safety.
4.9 Influence of slope angle on factor of safety (F.O.S) for medium dense sand slope
Also, numerical models were built with different slope angles 25º and 35º, polyurethane foam piles having variable lengths embedded in the medium dense sand, and having the same pile diameter 0.5 m to study the effect of slope angle on factor of safety (F.O.S). Figures 33, 34, 35, 36, 37, and 38 illustrate that increased the slope angles decreased the (F.O.S.). This is because increasing the angle of slope reduces the intersection of the critical slip surface with the piles and thus reduces the (F.O.S.) value for all cases.
5 Conclusions
This research has presented, A Finite Element analysis employing the GeoStudio 2D software to examine the importance of using PU foams to soil stabilization. Also, this research studies the use of PU as a new type of materials (polyurethane foam piles) (with different diameters, lengths, and pile spacing) injected in clay and sandy soils. The results demonstrated that after the PU was injected, the medium dense sand and medium clay characteristics were significantly improved. Many factors affect the improvement, including the type of soil, the length of injected polyurethane piles, the diameter of the piles, the pile spacing, and the slope angles. It can be concluded that:
-
1.
The PU foam has filled the soil voids, thereby enhancing the characteristics of the slope.
-
2.
PU foam is a lightweight material that may improve soil slope safety factors.
-
3.
The use of polyurethanes as a stabilizing medium for clay and sand soil is technically feasible, mostly because of how quickly they gel and harden. This makes them a good and rapid improvement approach, quick to create, and useful for rehabilitation projects.
-
4.
Percentage increase in F.O.S. increased with the decrease in pile spacing's for both soft clay soil and medium dense sand soil.
-
5.
Using polyurethane piles of diameter 0.5 m, 0.8 m, having spacing of 2.0 m, 1.0 m, 0.50 m, and sheet piles doesn't have any effect on the factor of safety for any pile length less than 9.0 m, but its effect appears from 9.0 m pile length for both types of soils (slope angle = 30°).
-
6.
Also, percentage increase in the F.O.S. continues to increase when using polyurethane piles of diameter 0.8 m, having spacing of 2.0 m, 1.0 m, 0.50 m, and sheet piles), the results show that the value of the factor of safety is constant without change until the length of the pile is about 8 m, after which there is an increase in the factor of safety because the critical slip surface does not pass through the pile until 8 m, and after that the critical slip surface cuts the pile, causing an increase in the factor of safety (slope angle = 30°).
-
7.
In addition, polyurethane piles having diameters of 0.5 m, and 0.8 m had the same increase in the factor of safety for medium sand soil until 8.0 m pile length (slope angle = 30°).
-
8.
The results showed that the percentage increase in the F.O.S. decreased with the increase in slope angles for soft clay soil. But, the increase in the factor of safety was found to increase with the increase in slope angles in case of sand soil.
-
9.
This study demonstrated that the use of polyurethane foam piles has a higher benefit when used in sandy soils than clay soils, because this soil contains a high percentage of voids, and when injected with polyurethane foam solidify the sand and the slope will be more resistant to failure.
-
10.
Comparing these results with those obtained using other stabilization methods, polyurethane reduces settlement; whenever the void ratio is high, the polyurethane fills and expands inside; as a result, the drop in the settlement is high and requires a low injection ratio. It is easy to inject the soil with P.U. comparing with other materials, also cost savings compared to other chemicals materials.
6 Suggestions for future studies
The research can be carried out in the following cases:
-
The study can be done using PLAXIS 3D to study the effects of PU as a new type of materials (polyurethane foam piles) (with different diameters, lengths, and pile spacing) injected in clay and sandy soils.
-
In this study, GeoStudio program was used to improve the F.O.S. for clay and sand soil. In future studies, the author recommends using software such as ABAQUS, Midas, and Flac to simulate these cases.
-
Study the influence ground water table on the F.O.S. for clay and sand.
-
This study can be extended to the use of inclined and horizontal piles and compare them with the results reached from this study.
Data availability
Data beyond what was provided in the article can, on a case by case basis, be made available to others on request to the corresponding author.
Abbreviations
- P.U.:
-
Polyurethane foam
- CBR:
-
California bearing ratio
- c:
-
Cohesion
- E:
-
Modulus of elasticity
- ν:
-
Poisson’s ratio
- L:
-
Pile length
- FER:
-
Free expansion ratio
- D:
-
Pile diameter
- γdry :
-
Dry unit weight
- S:
-
Pile spacing
- F.O.S.:
-
Factor of safety
- L/D:
-
Length/diameter ratio
- Ø:
-
Angle of internal friction
References
Abdulrasool AS, Al-Wakel SF (2021) Effects of polyurethane foam on the behaviour of collapsible soils. Geotech Res 8:108–116
Bai Y, Liu J, Xiao H, Song Z, Ma K, Deng Y (2023) Soil stabilization using synthetic polymer for soil slope ecological protection. Eng Geol 321:107155
Bowles JE (1997) Foundation analysis and design, 5th edn. Mc Graw-Hill Companies Inc, New York
Engin HK, Septanika EG, Brinkgreve RBJ (2007) Improved embedded beam elements for the modelling of piles. Taylor and Francis Group, London
Hassona FA, Abdelnaeem MM (2022) Physical and mechanical properties of polyurethane foam conditioned sand. MSc, Civil Engineering Department, Faculty of Engineering, Minia University
Hassona FA, Abdelnaeem MM (2023) Characterization of polyurethane foam conditioned sand. J Adv Eng Trends 42(2):199–218
Kumar A, Adithya H, Amith K, Akshar S, Rakshitha (2021) Experimental investigation on the effect of polyurethane foam on black cotton soil. Trends in civil engineering and challenges, vol 99. Springer Nature, Singapore, pp 421–432
Lat DC, Jais IBM, Ali N, Baharom B, Yunus NZM, Yusof DAM (2019) Uplift and settlement prediction model of marine clay soil e integrated with polyurethane foam. De Gruyter 9:481–489
Lat DC, Ali N, Jais IBM, Yunus NZM, Razali R, Talip AR (2020) A review of polyurethane as a ground improvement method. Mal J Fundam Appl Sci 16(1):70–74
Liu J, Chen Z, Kanungo DP, Song Z, Bai Y, Wang W, Li D, Qian W (2019) Topsoil reinforcement of sandy slope for preventing erosion using water-based polyurethane soil stabilizer. Eng Geol 252:125–135. https://doi.org/10.1016/j.enggeo.2019.03.003
Liu J, Chen Z, Zeng Z, Kanungo DP, Bu F, Bai X, Qi C, Qian W (2020) Influence of polyurethane polymer on the strength and mechanical behavior of sand-root composite. Fibers Polym 21(4):829–839
PLAXIS 2D-Tutorial Manual (2020) CONNECT edition V20.04, PLAXIS 2D
Polyntsev ES, Kvitko AV (2020) Using foam polyurethane sealers for strengthening of soils of a road bed of transport constructions. Mater Sci Eng. https://doi.org/10.1088/1757-899X/832/1/012029
Sabri MM, Shashkin KG, Zakharin E, Ulybin AV (2018) Soil stabilization and foundation restoration using an expandable polyurethane resin. Mag Civ Eng 82(6):68–80. https://doi.org/10.18720/MCE.82.7
Sabri MMS, Vatin NI, Alsaffar KAM (2021) Soil injection technology using an expandable polyurethane resin: a review. Polymers 13:1–32. https://doi.org/10.3390/polym13213666. (3666)
Tan P, Wang F, Guo C, Liu J (2023) Cyclic stress–strain characteristics of red clay treated with permeable water-soluble polyurethane. Transp Geotech 42:101072. https://doi.org/10.1016/j.trgeo.2023.101072
Wang W, Han M, Lin X, Li D, Yu H, Zhu L (2021) Influence of rainfall conditions on stability of slope reinforced by polymer anti-slide pile. Front Earth Sci 9:1–13 (Article 774926)
Wang W, Han M (2022) Optimal design of slope reinforcement by a new developed polymer micro anti-slide pile in case of emergency and disaster relief. Nat Hazards J Int Soc Prev Mitig Nat Hazards 112(1):899–917
Yong AL, Saleh KA, Yunus S, Mohd NZ, and Said KNM (2021) Improving the bearing capacity of marine clay using polyurethane columns. In: 4th National conference on wind & earthquake engineering. https://doi.org/10.1088/1755-1315/682/1/012023
Acknowledgements
First and foremost, the author would like to acknowledge ALLAH, the most merciful and compassionate, for giving them the strength to complete this work. Geotechnical Engineering Laboratory, Faculty of Engineering, and EL-Minia University, Computer laboratory of Civil Engineering Department of higher institute and technology in Minia. All professors of soil mechanics of Civil Engineering Department, Minia University for ultimate help, for offering useful suggestions.
Funding
This research received on external funding.
Author information
Authors and Affiliations
Contributions
Faek Hassona the originator of the basic idea of the research, participated in developing the theoretical model for the research, revise the paper. Beshoy Maher Hakeem participated in developing the theoretical model for the research, and was a major contributor in writing the manuscript, write the paper. All authors read and approved the final manuscript."
Corresponding author
Ethics declarations
Conflict of interest
On behalf of all authors, the corresponding author states that there is no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Hassona, F., Hakeem, B.M. Numerical modelling for stability of homogeneous clay and sand slopes improved by polyurethane foam piles in slope face. J. Umm Al-Qura Univ. Eng.Archit. (2024). https://doi.org/10.1007/s43995-024-00070-4
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s43995-024-00070-4