Abstract
Purpose
Measurement of draft is important for designing and testing a tillage implement or seeding machinery. This study aimed to develop an instrumentation setup which can be mounted between any category of tractor and different tillage implements for accessing real-time draft values while carrying out tillage.
Methods
A novel draft sensing device was developed along with lower hitch attachment for different categories of tractor and implement by measuring horizontal force at each hitch point using three force sensing units. The force sensing unit comprised an S-type loadcell packed between two U-shaped frame and a microcontroller-based data acquisition system. The finite element (FE) simulation was made to examine safety of the designed structure.
Results
The FE simulation result showed that stress induced on each element of force sensing unit was lesser than the yield strength of the material. The developed draft sensing device was tested both in the laboratory and in the field during tillage operation. The signals received from force sensing units were observed to be varied linearly with the applied load with negligible hysteresis losses.
Conclusion
The draft values measured by the developed draft sensing device were found to be accurate with mean absolute percentage error (MAPE), root mean square error (RMSE), and maximum absolute error (MAE) of 4.39%, 8.83 kg, and 7.14%, respectively.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Aboukarima, A. M. (2013). Evaluation of using a combination of simulated and experimental data to predict draft force of a moldboard plow. Misr Journal of Agricultural Engineering, 30(1), 1–28. https://doi.org/10.21608/MJAE.2013.102082
Agrawal, K. N., & Thomas, E. V. (2003). Relationship of specific draft with soil and operating parameters for M.B. plough. Agricultural Mechanization in Asia, Africa and Latin America, 34(2), 9–12. https://eurekamag.com/research/003/913/003913229.php
Akbarnia, A., Mohammadi, A., Farhani, F., & Alimardani, R. (2017). Simulation of draft force of winged share tillage tool using artificial neural network mode. Agricultural Engineering International: CIGR Journal, 16, 57–65.
Al-Hamed, S. A., Wahby, M. F., Al-Saqer, S. M., Aboukarima, A. M., & Sayedahmed, A. A. (2013). Artificial neural network model for predicting draft and energy requirements of disk plow. Journal of Animal & Plant Sciences, 23(6), 1714–1724. https://api.semanticscholar.org/CorpusID:73660026
Al-Jalil, H. F., Khdair, A., & Mukahal, W. (2001). Design and performance of an adjustable three-point hitch dynamometer. Soil and Tillage Research, 62, 153–156. https://doi.org/10.1016/S0167-1987(01)00219-7
Al-Janobi, A., & Al-Suhaibani, S. A. (1998). Draft of primary tillage implement in sandy loam soil. Applied Engineering in Agriculture, 14(4), 343–348. https://doi.org/10.13031/2013.19392
Almaliki, S., Himoud, M.S., & Muhsin, S.J. (2018). A stepwise regression algorithm for prognostication draft requirements of disk plough. In: International Conference on Promotion of Scientific & Regional Cooperation on Food and Agricultural Sciences, Mashhad. https://doi.org/10.36478/jeasci.2019.10335.10340
Al-Suhaibani, S. A., & Al-Janobi, A. (1997). Draught requirements of tillage implements operating on sandy loam soil. Journal of Agricultural Engineering Research, 66(3), 177–182. https://doi.org/10.1006/jaer.1996.0130
ASABE, D497.5. (2006). Agricultural machinery management data. ASABE St. Joseph, Mirch.
Bentaher, H., Hamza, E., Kantchev, G., Maalej, A., & Arnold, W. (2008). Three-point hitch mechanism instrumentation for tillage power optimization. Biosystems Engineering, 100, 24–30. https://doi.org/10.1016/j.biosystemseng.2008.01.008
Canakci, M., Topakci, M., Akinci, I., & Ozmerzi, A. (2005). Energy use pattern of some field crops and vegetable production: Case study for Antalya Region, Turkey. Energy Conversion and Management, 46, 655–666. https://doi.org/10.1016/j.enconman.2004.04.008
Chaplin, J., Lueders, M., & Zhao, Y. (1987). Three-point hitch dynamometer design and calibration. Applied Engineering in Agriculture, 3, 10–13. https://doi.org/10.13031/2013.26634
Chen, Y., McLaughlin, N. B., & Tessier, S. (2007). Double extended octagonal ring (DEOR) drawbar dynamometer. Soil and Tillage Research, 93, 462–471. https://doi.org/10.1016/j.still.2006.06.008
Cupera, J., Bauer, F., Severa, L., & Tatíček, M. (2011). Analysis of force effects measured in the tractor three-point linkage. Research in Agricultural Engineering, 57(3), 79–87. https://doi.org/10.17221/26/2010-RAE
Godwin, R. J., Reynolds, A. J., O’Dogherty, M. J., & Al-Ghazal, A. (1993). A triaxial dynamometer for force and moment measurements on tillage implements. Journal of Agricultural Engineering Research, 55, 189–205. https://doi.org/10.1006/JAER.1993.1043
Grisso, R. D., Yasin, M., & Kocher, M. F. (1996). Tillage implement forces operating in silty clay loam. Transaction of ASAE, 39(6), 1977–1982. https://doi.org/10.13031/2013.27699
Johnson, C. E., & Voorhees, W. B. (1979). A force dynamometer for three-point hitches. Transactions of the ASAE. https://doi.org/10.13031/2013.34994
Kheiralla, A. F., Yahya, A., Zohadie, M., & Ishak, W. (2003). Design and development of a three-point auto hitch dynamometer for an agricultural tractor. ASEAN Journal on Science and Technology for Development, 20(3&4), 271–288. https://doi.org/10.29037/ajstd.355
Kumar, A. A., Tewari, V. K., & Nare, B. (2016). Embedded digital draft force and wheel slip indicator for tillage research. Computers and Electronics in Agriculture, 127, 38–49. https://doi.org/10.1016/j.compag.2016.05.010
Marenya, M. (2009). Performance characteristics of deep tilling rotavator. Unpublished Ph.D thesis. South Africa: University of Pretotoria.
McLaughlin, N. B., Heslop, L. C., Buckley, D. J., St. Amour, G. R., Compton, B. A., Jones, A. M., & Van Bodegom, P. (1993). A general purpose tractor instrumentation and data logging system. Transaction of American Society of Agricultural Engineering, 36(2), 265–273. https://doi.org/10.13031/2013.28334
O’Dogherty, M. J. (1996). The design of octagonal ring dynamometer. Journal of Agricultural Engineering Research, 63, 9–18. https://doi.org/10.1006/jaer.1996.0002
Palmer, A. L. (1992). Development of a three-point linkage dynamometer for tillage research. Journal of Agricultural Engineering Research, 52, 157–167. https://doi.org/10.1016/0021-8634(92)80057-Y
Reid, J. T., Carter, L. M., & Clark, R. L. (1985). Draft measurements with a three-point hitch dynamometer. Transactions of the ASAE. https://doi.org/10.13031/2013.32208
Roul, A. K., Raheman, H., Pansare, S., & Machavaram, R. (2009). Predicting the draught requirement of tillage implements in sandy clay loam soil using an artificial neural network. Biosystems Engineering, 104, 476–485. https://doi.org/10.1016/j.biosystemseng.2009.09.004
Sahu, R. K., & Raheman, H. (2006). An approach for draft prediction of combination tillage implements in sandy clay loam soil. Soil and Tillage Research, 90(1–2), 145–155. https://doi.org/10.1016/j.still.2005.08.015
Scholtz, D. C. (1966). A three-point linkage dynamometer for restrained linkages. Journal of Agricultural Engineering Research, 11(1), 33–37. https://doi.org/10.1016/S0021-8634(66)80006-9
Thakur, T. C., & Godwin, R. J. (1988). Design of extended octagonal ring dynamometer for rotary studies. Agricultural Mechanization in Asia, Africa and Latin America, 19(3), 23–28.
Upadhyay, G., & Raheman, H. (2018). Performance of combined offset disc harrow (front active and rear passive set configuration) in soil bin. Journal of Terramechanics, 78, 27–37. https://doi.org/10.1016/j.jterra.2018.04.002
Upadhyay, G., & Raheman, H. (2019). Specific draft estimation model for offset disc harrows. Soil and Tillage Research, 191, 75–84. https://doi.org/10.1016/j.still.2019.03.021
Upadhyay, G., & Raheman, H. (2020). Comparative assessment of energy requirement and tillage effectiveness of combined (activepassive) and conventional offset disc harrows. Biosystems Engineering, 198, 266–279. https://doi.org/10.1016/j.biosystemseng.2020.08.014
Upadhyay, G., Raheman, H., & Dubey, R. (2022). Novel draught resistance sensing elements for measurement of drawbar power of agricultural machinery. Spanish Journal of Agriculture Research, 20(4), e0208. https://doi.org/10.5424/sjar/2022204-19171
Watyotha, C., & Salokhe, V. M. (2001). Development of a data acquisition system for measuring the characteristics of real time forces by cage wheels. Journal of Terramechanics, 38, 201–210. https://doi.org/10.1016/S0022-4898(00)00021-5
Acknowledgements
The facilities provided by the Department of Agricultural and Food Engineering, IIT Kharagpur, for carrying out this work are highly acknowledged.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of Interest
The authors have no conflicting financial or other interests.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Kumari, A., Raheman, H. Development of a Novel Draft Sensing Device with Lower Hitch Attachments for Tractor-Drawn Implements. J. Biosyst. Eng. 49, 20–28 (2024). https://doi.org/10.1007/s42853-023-00210-z
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s42853-023-00210-z