Abstract
Mechanical properties of semi-solid casting are dependent on multiple processing parameters, and improper processing parameters will not only reduce mean data but also increase variations. The present study investigated the impact of parameters in slurry preparation and heat treatment on the yield strength and ductility of T6 heat-treated A356 Al-Si alloy using rapid slurry forming (RSF) semi-solid casting. The focus was primarily on the robustness of mechanical properties based on Taguchi design method. By analyzing signal-to-noise ratio and minimum value calculated from \(\overline {\boldsymbol{x}} - 3S\), the optimum slurry preparation parameters and heat treatment parameters were determined to be no quench, enthalpy exchange material (EEM) temperature of 140 °C, EEM-to-melt ratio of 6mass%, stirring time of 18 s, solution heat treated at 520 °C for 2 h, and ageing heat treated at 190 °C for 6 h. In a small batch validation, the −3S yield strength and −3S elongation reach 256.1 MPa and 5.03% respectively, showing a satisfactory robustness. The hardness and microstructure of heat-treated samples with the best and worst properties were characterized to gain insight into the underlying mechanisms affecting the mean value and variations of mechanical properties.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Zhan H Y, Zeng G, Wang Q G, et al. Unified casting (UniCast) aluminum alloy-A sustainable and low-carbon materials solution for vehicle lightweighting. Journal of Materials Science & Technology, 2023, 154: 251–268.
Luo A A, Sachdev A K, Apelian D. Alloy development and process innovations for light metals casting. Journal of Materials Processing Technology, 2022, 306: 117606.
Vinarcik E J. High integrity die casting processes. John Wiley&Sons, Hoboken, 2002.
Luo A A. Recent advances in light metals and manufacturing for automotive applications. CIM Journal, 2021, 12: 79–87.
Seo P K, Kim H C, Kang C G. Numerical integration design process to development of suspension parts by semi-solid die casting process. Journal of Materials Processing Technology, 2007, 183(1): 18–32.
Wang P, Liu J. Semi-solid processing thoery and technology of aluminum alloy. Beijing: Science Press, 2016: 2–13. (In Chinese)
Zhang Z X, Chen T J, Liu K, et al. Efficient fabrication of semisolid nondendritic Al alloy slurry with high quality. China Foundry, 2022, 19(2): 117–130.
Haga T, Kapranos P. Simple rheocasting processes. Journal of Materials Processing Technology, 2002, 130: 594–598.
Hu X G, Zhu Q, Midson S P, et al. Blistering in semi-solid die casting of aluminium alloys and its avoidance. Acta Materialia, 2017, 124: 446–455.
Qi M, Kang Y, Xu Y, et al. New technique for preparing A356 alloy semisolid slurry and its rheo-diecast microstructure and properties. Nonferrous Metals Society of China, 2021, 31: 1868–1884.
Kang Y L, Li J Y, Li G N, et al. Preparation and rheological die-casting of 7075 aluminum alloy semisolid slurry. Journal of Net Shape Forming Engineering, 2020, 12: 3.
Marilyn N M, Mary J B. What does it “mean”? A review of interpreting and calculating different types of means and standard deviations. Pharmaceutics, 2017, 9: 14. doi: https://doi.org/10.3390/pharmaceutics9020014.
Winklhofer J. Semi-solid casting of aluminum from an industrial point of view. Solid State Phenomena, 2019, 285: 24–30.
Ratke L, Sharma A, Kohli D. Effect of process parameters on properties of Al-Si alloys cast by rapid slurry formation (RSF) technique. Materials Science and Engineering, 2012, 27(1). doi: https://doi.org/10.1088/1757-899X/27/1/012068.
Sharma S, Sharma A, Kumar S. Semi-solid forming of A356 Al alloy by rapid slurry forming process. In: Proc. 13th Internaitonal Conference on Aluminum Alloy, Pittsburgh, Pennsylvania, 2012.
Östklint M, Wessén M. Microstructure characteristics and semisolid slurry formation in binary Mg-Al alloys produced by the RheoMetal process. Solid State Phenomena, 2013, 192–193: 482–487.
Krishnaiah K, Shahabudeen P. Applied design of experiments and Taguchi methods. PHI Learning Private Limited, 2012.
Ji S, Wang Y, Waston D, et al. Microstructural evolution and solidification behaivior of Al-Mg-Si alloy in high-pressure die casting, Metallurgical and Materials Transactions: A, Physical Metallurgy and Meterail Science, 2013, 44(7): 3185–3197.
Niu G, Wang J, Li J P, et al. The formation mechanism of the chill fine-grain layer with high supersaturation and its influence on the mechanical properties of die casting Al-7Si-0.5Mg alloy. Material Sceince & Engineering A, 2022, 833: 142544.
Kaufman J G, Rooy E L. Heat treatment of aluminum castings, ASM handbook, 2011.
Musa Y, Ozurek D. The effects of Mg amount on microstructure and mechanical properties of Al-Si-Mg alloys. Materials and Design, 2013, 51: 767–774.
Long H C, Chen J H, Liu C H, et al. Microstructure evaluation during heat treatment for Al-7Si Alloy, Journal of Chinese Electron Microscopy Society, 2013, 32(1): 18–24. (In Chinese)
Colley L J, Wells M A, Poole W J. Microstructure-strength models for heat treatment of Al-Si-Mg casting alloys I: Microstructure evolution and precipitation kinetics. Canadian Metallurgical Quarterly, 2014, 53(2): 125–137.
Acknowledgements
The authors would like to acknowledge the support and assistance from Mr. Li-qun Zhu from Kingpin Precision Industrial (Suzhou) Co., Ltd., as well as Mr. Hai-quan Zhang and Mr. Han-ming Cheng from Hongjin Metal Aluminum Co., Ltd.
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.
Additional information
Yi-wu Xu Senior Engineer. His research interests mainly focus on casting process development, problem solving of casting defects, and preventing automotive casting failures. To date, He has published 12 technical papers. E-mail: yiwu.xu@gm.com
Rights and permissions
About this article
Cite this article
Xu, Yw., Zhan, Hy., Tong, W. et al. To improve robustness of mechanical properties of semi-solid cast A356 alloy using taguchi design method. China Foundry 21, 175–184 (2024). https://doi.org/10.1007/s41230-023-3039-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s41230-023-3039-9