Abstract
With modified water glass as binder and the introduction of micro silicon powders into the core-making process, an improvement was made to the tensile strength and collapsibility of the sand core. The potassium hydroxide, sodium hexametaphosphate and white sugar were applied as the modifiers of water glass. The optimum proportion of the modifiers was determined through the combination of single factor test and orthogonal test. The optimum proportion of water glass, potassium hydroxide, sodium hexametaphosphate and white sugar is 1000: 40: 5: 5 (wt.). In terms of weight, modified binder and micro silicon powders accounted for 2% and 0.6% of sand, respectively. The sand core was hardened by going through a warm core box process, in which the temperature of core box was 150 °C, and the compressed hot air was blown at 120 °C for 40 s under a pressure of 0.2 MPa. As for the sand core bonded with modified water glass, the tensile strength is 2.46 MPa at room temperature (σ0) and 2.49 MPa at 25 °C and 40% RH for 24 h (σ24), which are 2 times more than that with unmodified binder. The bonded strengths of sand core are increased as a result of the reaction between −OH groups from addition of potassium hydroxide and SiO2 particles widely distributed in the sand core. Comparing with the sand core bonded with unmodified water glass, the high temperature residual tensile strength (σr) of sand core bonded with modified water glass under 600 °C for 5 min, is sharply reduced from 0.20 MPa to 0.01 MPa. By the comparison with unmodified water glass, the dynamic viscosity of the modified water glass and the flowability of molding sand using modified water glass are increased from 74 mPa·s and 2.15 g to 80 mPa·s and 2.21 g, respectively. As revealed by FT-IR analysis, new groups including PO−3 , PO3−4 , and Si-O-C appear in the molecular structure of modified water glass, which are beneficial to the collapsibility of sand core.
Article PDF
Similar content being viewed by others
Avoid common mistakes on your manuscript.
References
Fan Z T, Long W, Liu F C. Environmental characteristics of mold casting and development trend of binder. Journal of Hubei University of Technology, 2014, 29(5): 1–5. (In Chinese)
Song L, Liu W H, Li Y M, et al. Humidity-resistant inorganic binder for sand core-making in foundry practice. China Foundry, 2018, 16(4): 267–271.
Ünlü N, Odabas A. Development and evaluation of a new ecofriendly sodium silicate-based binder system. International Journal of Metalcasting, 2018, 12: 765–771.
Fox J T, Cannon F S, Brown N R, et al. Comparison of a new green foundry binder with conventional foundry binders. International Journal of Adhesion & Adhesives, 2012, 34: 38–45.
Wang J, Yang J H, Zhao L. Study on recycling technology of sodium silicate based on green casting. Foundry Technology, 2018, 39(3): 533–536. (In Chinese)
Zaretskiy L. Hydrous solid silicates in new foundry binders. International Journal of Metalcasting, 2018, 12(2): 275–291.
Izdebska-Szanda I, Baliński A. New generation of ecological silicate binder. Engineering Procedia, 2011, 10: 887–893.
Zaretskiy L. Microsilica in sodium silicate bonded sands. International Journal of Metalcasting, 2019, 13(1): 58–72.
Nilsen E, Einarsrud M A, Puputti J, et al. Preparation and characterization of binder for inorganic composites made from amorphous mineral raw material. Journal of Sol-Gel Science and Technology, 2005, 35(2): 143–150.
Sun Y Q, Pan J Q, Chen L Z, et al. Effect of surface active agent on properties of sodium silicate sand. Journal of Technology, 2017, 17(1): 45–48. (In Chinese)
Yang C. Effect of ultra-fine powder modifying sodium silicate on foundry sand. Hot Working Technology, 2014, 43(19): 82–84. (In Chinese)
Zhu Y, Yu Y G, Zhou L S. Study on poly (ethylene oxide) modified sodium silicate binder. Foundry, 2006, 8(55): 839–841. (In Chinese)
Zaretskiy L. Modified silicate binder’s new developments and applications. International Journal of Metalcasting, 2015, 10(1): 88–99.
Kouassi S S, Tognonvi M T, Soro J, et al. Consolidation mechanism of materials obtained from sodium silicate solution and silica-based aggregates. Journal of Non-Crystalline Solids, 2011, 357(15): 3013–3021.
Tognonvi M T, Rossignol S, Bonnet J P. Effect of alkali cation on irreversible gel formation in basic medium. Journal of Non-Crystalline Solids, 2011, 357(1): 43–49.
Luukkonen T, Sreenivasan H, Abdollahnejad Z, et al. Influence of sodium silicate powder silica modulus for mechanical and chemical properties of dry-mix alkali-activated slag mortar. Construction and Building Materials, 2020, 233: 117354.
Zhu C X, Lu C, Ji D S. Basic theory of water glass sand. Shang Hai: Shanghai Jiaotong University Press, 2000: 67–68.
Tognonvi M T, Soro J, Rossignol S. Physical-chemistry of silica/alkaline silicate interactions during consolidation. Part 1: Effect of cation size. Journal of Non-Crystalline Solids, 2012, 358(1): 81–87.
Tognonvi M T, Soro J, Gelet J L, et al. Physico-chemistry of silica/Na silicate interactions during consolidation. Part 2: Effect of pH. Journal of Non-Crystalline Solids, 2012, 358(3): 492–501.
Weng S F, Xu Y Z. Fourier transform infrared spectrum analysis. Shang Hai: Shanghai Jiaotong University Press, 2016: 326–416.
Xu J. Infrared spectroscopy analysis of modified sodium silicate. Foundry, 2008, 57(8): 834–837. (In Chinese)
Author information
Authors and Affiliations
Corresponding author
Additional information
Wei-hua Liu Male, born in 1968, Associate Professor, Ph.D. His research interest mainly focuses on foundry materials. To date, he has published over 30 technical papers.
Rights and permissions
About this article
Cite this article
Xin, Fh., Liu, Wh., Song, L. et al. Modification of inorganic binder used for sand core-making in foundry practice. China Foundry 17, 341–346 (2020). https://doi.org/10.1007/s41230-020-0018-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s41230-020-0018-2