Abstract
This paper demonstrates a new methodology to characterise interfaces of thermoplastic multi-material combinations in nanometre scale. To visualise interfaces and possible interphases, scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and atomic force microscopy (AFM) were used. Isothermal “polymer-fusing” specimens as well as fused filament fabrication (FFF) manufactured parts of polyphenylsulfone (PPSU) and Polyetherimid (PEI) were produced and compared in this study. SEM and EDS measurements show the macroscopic interface structure whereas nanoscale AFM measurements were used to measure the stiffness gradient across the interface of multi-material combinations. Macroscopically, no mixing or mechanical interlocking through re-melting was observed. The dominant effects for creating the macroscopic surface morphology happen during first deposition. Under the investigated conditions (380 °C nozzle temperature and 220 °C print chamber temperature), the diffusion gradient at the centre of extrusions was measured to be above the required range to form full healing but still below the gradient at an interface formed with both materials held at 380 °C (above melting temperature) for 15 min. In addition, the gradient was measured to be lower at the edges of extrusions. These results show, that relevant intermixing of the polymers happens at the nanoscale.
Similar content being viewed by others
Data availability
The datasets generated during and/or analysed during the current study are available from the corresponding author upon reasonable request.
References
Ehrenstein GW (2011) Polymer-Werkstoffe: Struktur, Eigenschaften
Ultimaker (2023) Ultimaker S Series Material Compatibility, Website
Kuipers T et al (2022) Itil: interlaced topologically interlocking lattice for continuous dual-material extrusion. Addit Manuf 50:102495
Ermolai V, Others (2022) Mechanical behaviour of macroscopic interfaces for 3d printed multi-material samples
de Gennes PG (1971) Reptation of a polymer chain in the presence of fixed obstacles. J Chem Phys 55:572–579
Doi M, Edwards SF (1988) The theory of polymer dynamics, 73. Oxford University Press
Wool RP, O’Connor KM (1981) A theory crack healing in polymers. J Appl Phys 52:5953–5963
Wool RP, O’Connor KM (1982) Time dependence of crack healing. J Polym Sci: Polym Lett Edn 20:7–16
Kim YH, Wool RP (1983) A theory of healing at a polymer–polymer interface. Macromolecules 16:1115–1120
Wool RP et al (1989) Welding of polymer interfaces. Polym Eng Sci 29:1340–1367
Bastien LJ, Gillespie JW Jr (1991) A non-isothermal healing model for strength and toughness of fusion bonded joints of amorphous thermoplastics. Polym Eng Sci 31:1720–1730
Butler CA et al (1998) An analysis of mechanisms governing fusion bonding of thermoplastic composites. J Thermoplast Compos 11:338–363
Grünewald J (2018) Thermoplastic composite sandwiches for structural helicopter applications
Consul P et al (2021) Interlaminar strength in large-scale additive manufacturing of slow crystallizing polyaryletherketone carbon composites. Polym Int 70:1099–1108
Luchinsky DG, Others (2018) Molecular dynamics of ultem 9085 for 3d manufacturing: spectra, thermodynamic properties, and shear viscosity
Allum J et al (2020) Interlayer bonding has bulk-material strength in extrusion additive manufacturing: new understanding of anisotropy. Addit Manuf 34:101297
Coogan TJ, Kazmer DO (2020) Prediction of interlayer strength in material extrusion additive manufacturing. Addit Manuf 35:101368
Moetazedian A, Others (2021) Bulk-material bond strength exists in extrusion additive manufacturing for a wide range of temperatures, speeds, and layer times. 3D Print Addit Manuf
3DXtech (2023) Thermax Pei Made Using Ultem 1010
BASF (2021) Technical Data Sheet Ultrafuse Ppsu
Gleadall A (2021) Fullcontrol Gcode designer: open-source software for unconstrained design in additive manufacturing
Nečas D, Klapetek P (2012) Gwyddion: an open-source software for SPM data analysis. Cent Eur J Phys 10(1):181–188
Wool RP (1995) Polymer interfaces: structure and strength. Hanser Publishers
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
On behalf of all authors, the corresponding author states that there is no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Welker, R., Arikan, E., Zimmer, F. et al. Microscopic evaluation of polymer–polymer interfaces in multi-material additive manufacturing. Prog Addit Manuf (2024). https://doi.org/10.1007/s40964-024-00578-0
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s40964-024-00578-0