Skip to main content

Advertisement

SpringerLink
Log in

Properties and Interface Characteristics of Sodium Silicate Investment Shell Hardened Through Micro-droplet Spreading of Aluminum Potassium Sulfate Solution

  • Technical Paper
  • Published:
International Journal of Metalcasting Aims and scope Submit manuscript

Abstract

Sodium silicate shell for investment casting is widely used in parts production. However, the key problems with this technique are that the shell has a low green strength, fired strength, and high residual strength in the shell; as well as environmental pollution resulting from toxic gas containing ammonia from the evaporation of ammonia liquor used as a hardener during the hardening process. The former is related to uncontrollable hardening reaction process, while the latter is related to hardener characteristics. In this work, the microfluidic technique was employed to precisely control of the hardening reaction of the shells, and aluminum potassium sulfate solution served as replacement for ammonia liquor. The green, fired, and residual strength of the shell specimens and their high-temperature self-load deformation were investigated. It is found that the hardening reaction can be effectively controlled, and the hardening characteristics of the shells were obviously improved. The bending strength of the shells increases initially and then decreases at the time of micro-droplet spreading. The specimens hardened for 8 min by micro-droplet method reached the highest green strength level of 37.48 MPa, a fired strength of 10.07 MPa, and a lowest high-temperature self-load deformation value of 0.18%, about 150%, 65% higher, and 53% lower than by the current immersion method, respectively. Moreover, the fracture surfaces of the specimens were observed using scanning electron microscopy (SEM). The results reveal that the number of cracks in the sodium silicate gel film in the shell decreased significantly. The cracking tendency caused by shrinkage stress during hardening was reduced. This is due to the accurate reactant flow control provided a large number of microreactors for sodium silicate hardening. The hardener micro-droplets with an excellent monodispersity dispersed in a small volume on the surface of a continuous phase of water glass film, the volume shrinkage caused by micro-hardening can easily be compensated by the continuous phase of the liquid sodium silicate in the adjacent region and the cracking stress is partially or completely relaxed. The shrinkage trend in the process of dehydration polymerization of sodium silicate decreased and the bending strength of shell specimen improved. Microfluidic technique provides a powerful means for accurate delivery of reactant and control of gel structure during shell hardening.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Figure 1
Figure 2
Figure 3
Figure 4
Figure 5
Figure 6
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15

Similar content being viewed by others

References

  1. L. Nastac, M.N. Gungor, I. Ucok et al., Advances in investment casting of Ti–6Al–4V alloy: a review. Int. J. Cast Metal Res. 19, 73–93 (2006). https://doi.org/10.1179/136404605225023225

    Article  CAS  Google Scholar 

  2. F. Xin, W. Liu, L. Song et al., Modification of inorganic binder used for sand core-making in foundry practice. China Foundry 17, 341–346 (2020). https://doi.org/10.1007/s41230-020-0018-2

    Article  Google Scholar 

  3. R.S. Uwanyuze, J.E. Kanyo, S.F. Myrick et al., A review on alpha case formation and modeling of mass transfer during investment casting of titanium alloys. J. Alloy. Compd. 865, 158558 (2021). https://doi.org/10.1016/j.jallcom.2020.158558

    Article  CAS  Google Scholar 

  4. U. Purwar, M.A. Javed, S. Vidya, A review on research aspects and trends in rapid prototyping and tooling assisted investment casting. Mater. Today Proc. 46, 6704–6707 (2021). https://doi.org/10.1016/j.matpr.2021.04.172

    Article  Google Scholar 

  5. S. Pattnaik, D.B. Karunakar, P.K. Jha, Developments in investment casting process—a review. J. Mater. Process. Technol. 212, 2332–2348 (2012). https://doi.org/10.1016/j.jmatprotec.2012.06.003

    Article  CAS  Google Scholar 

  6. M. Popescu, V. Matei, L. Serban, Contributions to the mechanism of water glass hardening by using thermal analysis methods and X-ray diffractometry. J. Therm. Anal. Calorim. 37, 375–382 (1991). https://doi.org/10.1007/BF02055939

    Article  CAS  Google Scholar 

  7. L. Wang, Y. Zhang, Influence of additives on modification of sodium silicate and its molding sand properties. Adv. Mater. Res. 634, 2702–2706 (2013). https://doi.org/10.4028/www.scientific.net/AMR.634-638.2702

    Article  CAS  Google Scholar 

  8. L. Wang, W. Jiang, F. Liu et al., Investigation of parameters and mechanism of ultrasound-assisted wet reclamation of waste sodium silicate sands. Int. J. Cast Metal Res. 31, 169–176 (2018). https://doi.org/10.1080/13640461.2017.1405543

    Article  CAS  Google Scholar 

  9. H. Miao, X. Du, Y. Sun et al., Effect of powder breakdown additives on properties of ester-hardened sodium silicate bonded ceramic sand. Int. J. Metalcast. 15, 710–718 (2021). https://doi.org/10.1007/s40962-020-00517-z

    Article  CAS  Google Scholar 

  10. L.G. Znamenskii, O.V. Ivochkina, A.S. Varlamov, Acceleration of the formation on the sodium silicate binder in investment casting. Mater. Sci. Forum 946, 673–677 (2019). https://doi.org/10.4028/www.scientific.net/MSF.946.673

    Article  Google Scholar 

  11. M.S. Tsai, W.C. Wu, Aluminum modified colloidal silica via sodium silicate. Mater. Lett. 58, 1881–1884 (2004). https://doi.org/10.1016/j.matlet.2003.12.006

    Article  CAS  Google Scholar 

  12. S. Pattnaik, M.K. Sutar, Effect of saw dust content on slurry rheology and mechanical properties of the investment casting ceramic shell international. Int. J. Metalcast. 15, 470–487 (2021). https://doi.org/10.1007/s40962-020-00478-3

    Article  CAS  Google Scholar 

  13. S. Pattnaik, M.K. Sutar, Investigation on the influence of polyethylene wax powder on the characteristics of ceramic shells used for investment casting. SILICON 14, 6089–6096 (2022). https://doi.org/10.1007/s12633-021-01386-9

    Article  CAS  Google Scholar 

  14. S. Pattnaik, M.K. Sutar, Preparation and analysis of a hybrid ceramic shell for investment casting. Int. J. Adv. Manuf. Technol. 122, 2513–2527 (2022). https://doi.org/10.1007/s00170-022-10054-0

    Article  Google Scholar 

  15. S. Pattnaik, An investigation on enhancing ceramic shell properties using naturally available additives. Int. J. Adv. Manuf. Technol. 91, 3061–3078 (2017). https://doi.org/10.1007/s00170-016-9975-4

    Article  Google Scholar 

  16. S. Pattnaik, Influence of sawdust on the properties of the ceramic shell used in investment casting process. Int. J. Adv. Manuf. Technol. 93, 691–707 (2017). https://doi.org/10.1007/s00170-017-0559-8

    Article  Google Scholar 

  17. B.S. Lartiges, J.Y. Bottero, L.S. Derrendinger et al., Flocculation of colloidal silica with hydrolyzed aluminum: an 27Al solid state NMR investigation. Langmuir 13, 147–152 (1997). https://doi.org/10.1021/la951029x

    Article  CAS  Google Scholar 

  18. A.M. Abdulwahab, Y. Al-magdashi, A. Meftah et al., Growth, structure, thermal, electrical and optical properties of potassium aluminum sulfate dodecahydrate (potash alum) single crystal. Chin. J. Phys. 60, 510–521 (2019). https://doi.org/10.1016/j.cjph.2019.05.034

    Article  CAS  Google Scholar 

  19. L.G. Briendl, F. Mittermayr, A. Baldermann et al., Early hydration of cementitious systems accelerated by aluminium sulphate: effect of fine limestone. Cem. Concr. Res. 134, 106069 (2020). https://doi.org/10.1016/j.cemconres.2020.106069

    Article  CAS  Google Scholar 

  20. Y. Zhang, S. Yuan, Y. Gao, Spatial distribution and transient evolution of sub-droplet velocity and size in ultrasonic atomization. Exp. Therm. Fluid Sci. 140, 110761 (2023). https://doi.org/10.1016/j.expthermflusci.2022.110761

    Article  CAS  Google Scholar 

  21. T. Kudo, K. Sekiguchi, K. Sankoda et al., Effect of ultrasonic frequency on size distributions of nanosized mist generated by ultrasonic atomization. J. Ultrason. Sonochem. 37, 16–22 (2017). https://doi.org/10.1016/j.ultsonch.2016.12.019

    Article  CAS  Google Scholar 

  22. L.Y. Yeo, J.R. Friend, M.P. McIntosh et al., Ultrasonic nebulization platforms for pulmonary drug delivery. Expert Opin. Drug. Del. 7, 663–679 (2010). https://doi.org/10.1517/17425247.2010.485608

    Article  CAS  Google Scholar 

  23. P. Li, M. Yu, K. Gao et al., Rapid preparation of hydrogen barrier films by a novel ultrasonic atomization-assisted layer-by-layer self-assembly method. Int. J. Hydrog. Energ. 48, 25783–25796 (2023). https://doi.org/10.1016/j.ijhydene.2023.03.273

    Article  CAS  Google Scholar 

  24. L. Song, W. Liu, F. Liu et al., Study of adhesion properties and mechanism of sodium silicate binder reinforced with silicate fume. Int. J. Adhes. Adhes. 106, 1028200 (2021). https://doi.org/10.1016/j.ijadhadh.2021.102820

    Article  CAS  Google Scholar 

Download references

Acknowledgments

This work was supported by the Natural Science Foundation of Inner Mongolia Autonomous Region, P.R. China, under the contracts No.2023MS05001, and the Basic Scientific Research Expenses Program of Universities directly under Inner Mongolia Autonomous Region (Grant No. JY20220036).

Author information

Authors and Affiliations

  1. School of Materials Science and Engineering, Inner Mongolia University of Technology, Hohhot, 010051, People’s Republic of China

    Silong Li, Xiangdong Liu, Hua Feng, Zhijun Chen & Chang Liu

  2. Key Laboratory at Universities for Materials Processing & Control Engineering of Inner Mongolia Autonomous Region, Hohhot, 010051, People’s Republic of China

    Silong Li, Xiangdong Liu & Chang Liu

Authors
  1. Silong Li
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Xiangdong Liu
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Hua Feng
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Zhijun Chen
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Chang Liu
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding authors

Correspondence to Xiangdong Liu or Chang Liu.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Li, S., Liu, X., Feng, H. et al. Properties and Interface Characteristics of Sodium Silicate Investment Shell Hardened Through Micro-droplet Spreading of Aluminum Potassium Sulfate Solution. Inter Metalcast (2024). https://doi.org/10.1007/s40962-024-01276-x

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1007/s40962-024-01276-x

Keywords

Search

Navigation