Abstract
The Brazilian disc test has been used widely to measure the tensile strength of brittle materials, such as rock and ceramic. However, the Brazilian disc method developed for rock has not been applicable for nuclear graphite due to the large ratio of tensile to compressive strength in the material. According to the results of stress analysis and Griffith’s strength criteria, the graphite compressive stress near the contact area must be decreased for the Brazilian tensile strength method. In this paper, the Brazilian disc test has been modified by using a newly developed anvil with a V-shaped cavity. According to finite element analysis, the stress concentration around the contact area between graphite samples and anvils was significantly reduced by the new design of anvils. The design has been proved to be effective by comparing with the direct methods. The method also has been proved to be valid for different samples sizes considered in this study, which indicates that it has a wide applicability.
Similar content being viewed by others
References
Maul PR, Robinson PC, Northrop PJ (2011) Statistical modelling of graphite brick cracking in advanced gas-cooled reactors. Appl Statist 60:339–353. https://doi.org/10.1111/j.1467-9876.2010.00745.x
Xu YH, Zuo KF (2002) Overview of the 10 MW high temperature gas cooled reactor-test module project. Nucl Eng Des 218:13–23. https://doi.org/10.1016/S0029-5493(02)00181-4
Wu ZX, Lin DC, Zhong DX (2002) The design features of the HTR-10. Nucl Eng Des 218(1–3):25–32. https://doi.org/10.1016/S0029-5493(02)00182-6
Jérôme S, Michel A, Ondrej B (2014) The molten salt reactor (MSR) in generation IV: Overview and perspectives. Prog Nucl Energ 77:308–319. https://doi.org/10.1016/j.pnucene.2014.02.014
Rosenthal MW, Kasten PR, Briggs RB (1970) Molten-Salt Reactors-History, Status, and Potential. Nucl Appl Technol 8:107–117
Burchell T, Yahr T, Battiste R (2007) Modeling the multiaxial strength of H-451 nuclear grade graphite. Carbon 45:2570–2583. https://doi.org/10.1016/j.carbon.2007.08.015
Wang HT, Sun LB, Li CF (2012) An evaluation on fatigue crack growth in a fine-grained isotropic graphite. Nucl Eng Des 250:197–206. https://doi.org/10.1016/j.nucengdes.2012.05.043
Wang C, Zhang Z, Yu S (2001) Assessment of graphite strength in the HTR. Nucl Power Eng 22:321–323
ASTM C749–15 Standard test method for tensile stress-strain of carbon and graphite.
DIN 51914–2009 Testing of carbonaceous materials-determination of tensile strength-solid materials.
Ma SP, Yan D, Wang X (2011) Damage observation and analysis of a rock Brazilian disc using high-speed DIC method. Appl Mech Mater 70:87–92
Wang Y, Li C, Hu Y (2017) Brazilian test for tensile failure of anisotropic shale under different strain rates at quasi-static loading. Energies 10:13–24
Na SH, Sun WC, Ingraham MD (2017) Effects of spatial heterogeneity and material anisotropy on the fractur pattern and macroscopic effective toughness of Mancos Shale in Brazilian tests. J Geophys Res Solid Earth 122:6202–6230
ASTM D3967–16, Standard test method for splitting tensile strength of intact rock core specimens. https://doi.org/10.1520/D3967-16
Wang QZ, Xing L (1999) Determination of fracture toughness KIC by using the flattened Brazilian disk specimen for rocks. Eng Fract Mech 64:193–201. https://doi.org/10.1016/S0013-7944(99)00065-X
Ayatollahi MR, Aliha MRM (2005) Cracked Brazilian disc specimen subjected to mode II deformation. Eng Fract Mech 72:493–503. https://doi.org/10.1016/j.engfracmech.2004.05.002
Bieniawski ZT, Hawkes I (1978) Suggested methods for determining tensile strength of rock materials. Int J Rock Mech Min Sci Geomeeh Abstr 15:99–103. https://doi.org/10.1016/0148-9062(78)90003-7
ASTM D3967–08 Standard Test Method for Splitting Tensile Strength of Intact Rock Core Specimens. https://doi.org/10.1520/D3967-08
Hou C, Wang Z, Liang W (2016) Determination of fracture parameters in center cracked circular discs of concrete under diametral loading: A numerical analysis and experimental results. Theor Appl Fract Mech 85:355–366. https://doi.org/10.1016/j.tafmec.2016.04.006
Ayatollahi MR, Torabi AR (2011) Failure assessment of notched polycrystalline graphite under tensile-shear loading. Mater Sci Eng A 528:5685–5695. https://doi.org/10.1016/j.msea.2011.04.066
Zhou YX, Xia K, Li XB (2012) Suggested methods for determining the dynamic strength parameters and mode-I fracture toughness of rock materials. Int J Rock Mech & Mining Sc 49:105–112
Griffith AA (1920) The phenomenon of rupture and flow in solids. Phil Trans R Soc Lond A 221:163–198. https://doi.org/10.1098/rsta.1921.0006
Wang QZ, Jia XM, Kou SQ (2004) The flattened Brazilian disc specimen used for testing elastic modulus, tensile strength and fracture toughness of brittle rocks: analytical and numerical results. Int J Rock Mech & Mining Sc 41:245–253. https://doi.org/10.1016/S1365-1609(03)00093-52
Haeri H, Khaloo A, Marji MF (2015) Experimental and numerical simulation of the microcrack coalescence mechanism in rock-like materials. Strength Mater 47:740–754. https://doi.org/10.1007/s11223-015-9711-6
Fairhurst C (1964) On the validity of the ‘Brazilian’ test for brittle materials. Int. J. Rock Mech & Mining Sc 1:535–546. https://doi.org/10.1016/0148-9062(64)90060-9
Awaji H, Sato S (1987) Diametral compressive stress considering the Hertzian contact. J Soc Mater Sc Jpn 27:336–341
Yu Y, Zhang JX, Zhang JC (2009) A modified Brazilian disk tension test. Int J Rock Mech & Mining Sc 46:421–425
Komurlu E, Kesimal (2015) A Evaluation of indirect tensile strength of rocks using different types of jaws. Rock Mech Rock Eng 48:1723–1730. https://doi.org/10.1007/s00603-014-0644-3
Japaridze L (2015) Stress-deformed state of cylindrical specimens during indirect tensile strength testing. J Rock Mech Geotech Eng 7: 509–518. DIO: https://doi.org/10.1016/j.jrmge.2015.06.006
Markides CF, Kourkoulis SK (2015) The influence of jaw’s curvature on the results of the Brazilian disc test. J Rock Mech Geotech Eng xxx:1–20. https://doi.org/10.1016/j.jrmge.2015.09.008
Zhu WC, Tang CA (2006) Numerical simulation of Brazilian disk rock failure under static and dynamic loading. Int J Rock Mech & Mining Sc 43:236–252. https://doi.org/10.1016/j.ijrmms.2005.06.008
Joyce MR, Marrow TJ, Mummery P (2008) Observation of microstructure deformation and damage in nuclear graphite. Eng Fract Mech 75:3633–3645
Zhang XJ, Yi YN, Zhu HB (2018) Measurement of tensile strength of nuclear graphite based on ring compression test. J Nucl Meter 511:134–140
ASTM D7219–08 (2014) Standard specification for isotropic and near-isotropic nuclear graphites. https://doi.org/10.1520/D7219-08R14
Hondros G (1959) The evaluation of Poisson’s ratio and the modulus of materials of a low tensile resistance by the Brazilian (indirect tensile) test with particular reference to concrete. Aust J Appl Sci 10:243–268
Lanaro F, Sato T, Stephansson O (2009) Microcrack modelling of Brazilian tensile tests with the boundary element method. Int J Rock Mech & Mining Sc 46:450–461
Akazawa T (1943) New test method for evaluating internal stress due to compression of concrete (the splitting tension test) (part 1). J Jpn Soc Civ Eng 29:777–787
Acknowledgements
This work is supported by the National Natural Science Foundation of China (No.51602335, No. 11305240, No. 51602336), the “Strategic Priority Research Program” of the Chinese Academy of Sciences (No. XDA02040200), Science Foundation of Shanghai (No. 16ZR1443400) and Joint funding of the National Natural Science Foundation of China (No.U1632268).
Author information
Authors and Affiliations
Corresponding authors
Ethics declarations
Conflict of Interest
On behalf of all authors, the corresponding author states that there is no conflict of interest.
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Zhang, C., Yuan, Y., He, Z. et al. Determination of Tensile Strength by Modified Brazilian Disc Method for Nuclear Graphite. Exp Tech 44, 475–484 (2020). https://doi.org/10.1007/s40799-020-00363-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40799-020-00363-y