Skip to main content
SpringerLink
Log in

Characterization and experimental evaluation of PVD AlTiN and TiN/TiAlN coatings for dry turning of DSS2205

  • Technical Paper
  • Published:
Journal of the Brazilian Society of Mechanical Sciences and Engineering Aims and scope Submit manuscript

Abstract

DSS are more suitable alternatives for the applications requiring vehement resistance to corrosion in severe conditions and to stress corrosion cracking. Work hardening tendency, high toughness, design strength and built-up layer (BUL) formation contribute to machining difficulty of duplex stainless steel (DSS2205). The present investigations are aimed to detail machining performance in terms of tool wear, tool life and cutting temperatures. Comparison of performance of AlTiN coating using two advanced PVD coating deposition techniques, viz. HiPIMS and S3p, with multilayer TiN/TiAlN coating is studied. The coating deposition processes using S3p technique were carried out in a vacuum chamber at a pressure of 1.33 × 10–2 Pa to 1.33 × 10–8 Pa. AlTiN-coated tool deposited using S3p technique proved better, exhibiting the highest tool life of 7105 mm, three times more than uncoated tools, and ahead of AlTiN-coated tool deposited by HiPIMS technique (5390 mm). Among the coated tools, TiN/AlTiN-coated tools showed the highest rate of rise in cutting temperatures as 14 and 21%, for rise in cutting speeds from 100 to 140 m/min and from 140 to 180 m/min, respectively. Experimental results of cutting temperatures are found in close agreement with results of Boothroyd model within an error of ± 10%.

Graphical abstract

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15

Similar content being viewed by others

References

  1. ISSM (2019) Stainless steel in figures 2019. Int. Stainl. Steel Forum, pp 1–24

  2. Gunn RN (1997) Duplex stainless steels: microstructure, properties and applications, 1st edn. Woodhead Publishing, Cambridge

    Book  Google Scholar 

  3. Selvaraj DP, Chandrasekar P (2018) Experimental investigations of nitrogen alloyed duplex stainless steel in dry milling process. J Eng Sci Technol 13:321–331

    Google Scholar 

  4. IMoA (2014) Practical guidelines for the fabrication of duplex stainless steels, 3rd edn. International Molybdenum Association (IMoA), London

  5. SubhashSoumya N, Soumya S, Raj N, Jagadeesha T (2019) Experimental study on tool wear and optimization of process parameters using ANN-GA in turning of super-duplex stainless steel under dry and wet conditions. Adv Manuf Technol. https://doi.org/10.1007/978-981-13-6374-0_47

    Article  Google Scholar 

  6. Królczyk G, Gajek M, Legutko S (2013) Effect of the cutting parameters impact on tool life in duplex stainless steel turning process. Teh Vjesn 20:587–592

    Google Scholar 

  7. Nilsson J-O (1992) Overview super duplex stainless steels. Mater Sci Technol 8:685–700. https://doi.org/10.1179/mst.1992.8.8.685

    Article  Google Scholar 

  8. Voronenko B (1997) Austenitic-ferritic stainless steels: a state of the art review. Met Sci Heat Treat 39:428–437. https://doi.org/10.1007/BF02484228

    Article  Google Scholar 

  9. Nomani J, Pramanik A, Hilditch T, Littlefair G (2017) Stagnation zone during the turning of duplex SAF 2205 stainless steels alloy. Mater Manuf Process 32:1486–1489. https://doi.org/10.1080/10426914.2017.1279289

    Article  Google Scholar 

  10. Selvaraj PD, Chandramohan P, Mohanraj M (2014) Optimization of surface roughness, cutting force and tool wear of nitrogen alloyed duplex stainless steel in a dry turning process using Taguchi method. Meas J Int Meas 49:205–215. https://doi.org/10.1016/j.measurement.2013.11.037

    Article  Google Scholar 

  11. Krolczyk G, Nieslony P, Legutko S (2014) Microhardness and surface integrity in turning process of duplex stainless steel (DSS) for different cutting conditions. J Mater Eng Perform 23:859–866. https://doi.org/10.1007/s11665-013-0832-4

    Article  Google Scholar 

  12. Koyee RD, Heisel U, Schmauder S, Eisseler R (2014) Experimental investigation and multiobjective optimization of turning duplex stainless steels. Int J Manuf Eng 1:1–13

    Google Scholar 

  13. Soumya S, Subhash N, Raj N, Jagadeesha T (2019) Experimental study on surface roughness and optimization of process parameters using ANN-GA in milling of super-duplex stainless steel under dry and wet conditions. Adv Manuf Technol. https://doi.org/10.1007/978-981-13-6374-0_46

    Article  Google Scholar 

  14. Kulkarni AP, Sargade VG (2015) Characterization and performance of AlTiN, AlTiCrN, TiN/TiAlN PVD coated carbide tools while turning SS 304. Mater Manuf Process 30:748–755. https://doi.org/10.1080/10426914.2014.984217

    Article  Google Scholar 

  15. Sonawane GD, Sargade VG (2019) Evaluation and multi-objective optimization of nose wear, surface roughness and cutting forces using grey relation analysis (GRA). J Braz Soc Mech Sci Eng 41:1–13. https://doi.org/10.1007/s40430-019-2057-4

    Article  Google Scholar 

  16. Bunshah R (2002) Handbook of hard coatings. William Andrew Publishing

  17. He HB, Han WQ, Li HY, Li DY, Yang J, Gu T, Deng T (2014) Effect of deep cryogenic treatment on machinability and wear mechanism of TiAlN coated tools during dry turning. Int J Precis Eng Manuf 15:655–660. https://doi.org/10.1007/s12541-014-0384-z

    Article  Google Scholar 

  18. Staszuk M, Pakuła D, Chladek G, Pawlyta M, Pancielejko M, Czaja P (2018) Investigation of the structure and properties of PVD coatings and ALD + PVD hybrid coatings deposited on sialon tool ceramics. Vacuum 154:272–284. https://doi.org/10.1016/j.vacuum.2018.04.032

    Article  Google Scholar 

  19. Galanis D (2008) Comparison between dry and wet machining of stainless steel. In: Bouzakis PK-D (ed) Proc. 3rd Int. Conf. Manuf. Eng., Aristoteles University of Thessaloniki and Project Center Coatings in Manufacturing (PCCM), Greece, pp 1–3

  20. Sonawane GD, Sargade VG (2020) Machinability study of duplex stainless steel 2205 during dry turning. Int J Precis Eng Manuf. https://doi.org/10.1007/s12541-019-00305-8

    Article  Google Scholar 

  21. Diniz AE, Micaroni R (2002) Cutting conditions for finish turning process aiming: the use of dry cutting. Int J Mach Tools Manuf 42:899–904

    Article  Google Scholar 

  22. Krolczyk G, Nieslony AP, Maruda RW (2016) Dry cutting effect in turning of a duplex stainless steel as a key factor in clean production. J Clean Prod 30:1–12

    Google Scholar 

  23. Thiele JD, Melkote S (1999) Effect of cutting edge geometry and workpiece hardness on surface generation in the finish hard turning of AISI 52100 steel. J Mater Process Technol 94:216–226. https://doi.org/10.1016/S0924-0136(99)00111-9

    Article  Google Scholar 

  24. Castro G, Almeida FA, Oliveira FJ, Fernandes AJS, Sacramento J, Silva RF (2008) Dry machining of silicon-aluminium alloys with CVD diamond brazed and directly coated Si3N4 ceramic tools. Vacuum 82:1407–1410. https://doi.org/10.1016/j.vacuum.2008.03.042

    Article  Google Scholar 

  25. Kelly PJ, Arnell RD (2000) Magnetron sputtering: a review of recent developments and applications. Vacuum 56:159–172. https://doi.org/10.1016/S0042-207X(99)00189-X

    Article  Google Scholar 

  26. Voevodin AA, Zabinski JS (2005) Nanocomposite and nanostructured tribological materials for space applications. Compos Sci Technol 65:741–748. https://doi.org/10.1016/J.COMPSCITECH.2004.10.008

    Article  Google Scholar 

  27. Rajaguru J, N. Arunachalam J (2017) Coated tool performance in dry turning of super duplex stainless steel. In: 45th SME North Am. Manuf. Res. Conf. NAMRC 45, LA, USA. Elsevier, pp 601–611. https://doi.org/10.1016/J.PROMFG.2017.07.061

  28. Krolczyk GM, Nieslony P, Legutko S (2015) Determination of tool life and research wear during duplex stainless steel turning. Arch Civ Mech Eng 15:347–354. https://doi.org/10.1016/j.acme.2014.05.001

    Article  Google Scholar 

  29. Inspektor A, Salvador PA (2014) Architecture of PVD coatings for metalcutting applications: a review. Surf Coat Technol 257:138–153. https://doi.org/10.1016/j.surfcoat.2014.08.068

    Article  Google Scholar 

  30. Barshilia HC, Deepthi B, Selvakumar N, Jain A, Rajam KS (2007) Nanolayered multilayer coatings of CrN/CrAlN prepared by reactive DC magnetron sputtering. Appl Surf Sci 253:5076–5083

    Article  Google Scholar 

  31. Chang YY, Yang SJ, Wang DY (2006) Structural and mechanical properties of AlTiN/CrN coatings synthesized by a cathodic-arc deposition process. Surf Coat Technol 201:4209–4214. https://doi.org/10.1016/j.surfcoat.2006.08.062

    Article  Google Scholar 

  32. Chen L, Du Y, Yin F, Li J (2007) Mechanical properties of (Ti, Al)N monolayer and TiN/(Ti, Al)N multilayer coatings. Int J Refract Met Hard Mater 25:72–76. https://doi.org/10.1016/j.ijrmhm.2006.01.005

    Article  Google Scholar 

  33. Vetter J (2014) Innovative PVD processes for advanced coatings based on HiPIMS and arc: scalable pulsed power plasma and high ionization triple. In: Funct. Coatings Surf. Eng., Oerlikon Balzer, Montreal, Canada, pp 1–20

  34. Abhang LB, Hameedullah M (2018) Modeling and analysis of tool wear based on cutting force and chip-tool interface temperatures in turning. In: Adv. Manuf. Mater. Sci.. Springer, Berlin, pp 411–420. https://doi.org/10.1007/978-3-319-76276-0

  35. Donnet C, Erdemir A (2004) Historical developments and new trends in tribological and solid lubricant coatings. Surf Coat Technol. https://doi.org/10.1016/j.surfcoat.2003.10.022

    Article  Google Scholar 

  36. Slusarczyk L (2017) The implementation of a thermal imaging camera for testing the temperature of the cutting zone in turning. In: Photonics Appl. Astron. Commun. Ind. High-Energy Phys. Exp., pp 1–6. https://doi.org/10.1117/12.2249298

  37. Bhirud NL, Gawande RR (2017) Measurement and prediction of cutting temperatures during dry milling: review and discussions. J Braz Soc Mech Sci Eng 39:5135–5158. https://doi.org/10.1007/s40430-017-0869-7

    Article  Google Scholar 

  38. Petkovik D, Madic M, Jankovik P, GM R (2016) Modelling of cutting temparatures in the biomedical stainless steel turning process. Themal Sci 20:1345–1354

    Article  Google Scholar 

  39. Boothroyd G (2017) Fundamentals of machining and machine tools, 3rd edn. Taylor and Francis, London

    Google Scholar 

  40. Davim JP (ed) (2011) Davim, machining of hard materials. Springer, London

  41. Rupetsov V, Minchev R (2016) Experimental calo tester for the coating thickness measurement. In: XV Int. Sci. Conf., pp 188–192

  42. Baptista A, Silva F, Porteiro J, Míguez J, Pinto G (2018) Sputtering physical vapour deposition (PVD) coatings: a critical review on process improvement and market trend demands. Coatings. https://doi.org/10.3390/COATINGS8110402

    Article  Google Scholar 

  43. Bujak J, Walkowicz J, Kusiński J (2004) Influence of the nitrogen pressure on the structure and properties of (Ti, Al)N coatings deposited by cathodic vacuum arc PVD process. Surf Coat Technol 180–181:150–157. https://doi.org/10.1016/j.surfcoat.2003.10.058

    Article  Google Scholar 

  44. Chen L, Xu YX, Du Y, Liu Y (2015) Effect of bilayer period on structure, mechanical and thermal properties of TiAlN/AlTiN multilayer coatings. Thin Solid Films 592:207–214. https://doi.org/10.1016/j.tsf.2015.09.029

    Article  Google Scholar 

  45. Zha X, Jiang F, Xu X (2017) Investigation of modelling and stress distribution of a coating/substrate system after an indentation test. Int J Mech Sci 134:1–14. https://doi.org/10.1016/j.ijmecsci.2017.10.002

    Article  Google Scholar 

  46. de Paiva JMF, Torres RD, Amorim FL, Covelli D, Tauhiduzzaman M, Veldhuis S, Dosbaeva G, Fox-Rabinovich G (2017) Frictional and wear performance of hard coatings during machining of superduplex stainless steel. Int J Adv Manuf Technol 92:423–432. https://doi.org/10.1007/s00170-017-0141-4

    Article  Google Scholar 

  47. Hao G, Liu Z, Liang X, Zhao J (2019) Influences of TiAlN coating on cutting temperature during orthogonal machining H13 hardened steel. Coatings. https://doi.org/10.3390/coatings9060355

    Article  Google Scholar 

  48. Zha X, Chen F, Jiang F, Xu X (2019) Correlation of the fatigue impact resistance of bilayer and nanolayered PVD coatings with their cutting performance in machining Ti–6Al–4V. Ceram Int 45:14704–14717

    Article  Google Scholar 

  49. Guo B, Zhang L, Cao L, Zhang T, Jiang F, Yan L (2017) The correction of temperature-dependent vickers hardness of cemented carbide base on the developed high-temperature hardness tester. J Mater Process Technol. https://doi.org/10.1016/j.jmatprotec.2017.12.041

    Article  Google Scholar 

  50. Boing D, de Oliveira AJ, Schroeter RB (2020) Evaluation of wear mechanisms of PVD and CVD coatings deposited on cemented carbide substrates applied to hard turning. Int J Adv Manuf Technol 106:5441–5451. https://doi.org/10.1007/s00170-020-05000-x

    Article  Google Scholar 

  51. Zha X, Jiang F, Xu X (2018) Investigating the high frequency fatigue failure mechanisms of mono and multilayer PVD coatings by the cyclic impact tests. Surf Coat Technol. https://doi.org/10.1016/j.surfcoat.2018.03.101

    Article  Google Scholar 

  52. Mia M (2018) Mathematical modeling and optimization of MQL assisted end milling characteristics based on RSM and Taguchi method. Measurement 121:249–260. https://doi.org/10.1016/J.MEASUREMENT.2018.02.017

    Article  Google Scholar 

Download references

Acknowledgements

The authors would like to express gratitude to CemeCon, Germany, and Balzer, India, for providing timely support regarding coating of cutting tools.

Funding

This work was supported by the NEB and Department of Science and Technology (DST), Govt. of India, under the grant ref: 11/10/2015-NEB (G)/03 dated 27/09/2017.

Author information

Authors and Affiliations

  1. Dr. Babasaheb Ambedkar Technological University, Raigad, India, 402103

    Gaurav D. Sonawane, Suresh R. Nipanikar & Vikas G. Sargade

  2. Sandip Foundation’s SITRC, Nashik, India, 422006

    Gaurav D. Sonawane

  3. Karmaveer Bhaurao Patil College of Engineering, Satara, Maharashtra, India, 415001

    Suresh R. Nipanikar

Authors
  1. Gaurav D. Sonawane
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Suresh R. Nipanikar
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Vikas G. Sargade
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Gaurav D. Sonawane.

Ethics declarations

Conflict of interest

The authors declare that there is no conflict of interest, and authors have full control of all the data included in the manuscript, and authors are agree to allow this journal to review their data, if required.

Ethical approval

The manuscript does not contain any clinical studies or patient data.

Additional information

Technical Editor: Izabel Fernanda Machado.

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Springer Nature or its licensor holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Sonawane, G.D., Nipanikar, S.R. & Sargade, V.G. Characterization and experimental evaluation of PVD AlTiN and TiN/TiAlN coatings for dry turning of DSS2205. J Braz. Soc. Mech. Sci. Eng. 44, 479 (2022). https://doi.org/10.1007/s40430-022-03775-6

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1007/s40430-022-03775-6

Keywords

Search

Navigation