Abstract
Laser transmission welding (LTW) causes a temperature rise at the weld interface which leads to melting, molecular diffusion and ultimately joining of the two components. Weld temperatures increase with laser power at a given scan speed. However, at higher temperatures, it has been observed that weld strength starts to decline due to material thermal degradation. Thermal degradation is a kinetic phenomenon which depends on both temperature and time. Thermal gravimetric analysis (TGA) is used to study the thermal degradation of two commonly used thermoplastic materials: polycarbonate (PC) and polyamide 6 (PA6). Each material was studied at several levels of carbon black (CB). The TGA data were then used to obtain the kinetic triplets (frequency factor, activation energy and reaction model) of the materials using a non-linear model-fitting method. These kinetic triplets were combined with temperature-time data obtained from a finite element method (FEM) simulation of the LTW process to predict material degradation. The conditions predicted to cause thermal degradation were then compared with experimental data. It is found that the predicted onset of material degradation is in reasonable agreement with both the onset of experimentally observed degradation and the onset of weld strength decline for PC and PA6.
Similar content being viewed by others
References
Grewell DA, Benatar A, Park JB (2003) Plastics and composites welding handbook. Hanser, Munich
Bates PJ, Khosravi S, Zak G (2011) Polymer degradation during contour laser transmission welding of PBT, Society of Plastics Engineers (SPE) Annual Technical Conference (ANTEC)
Chen M, Zak G, Bates PJ, Baylis B, McLeod M (2011) Experimental Study on Gap Bridging in Contour Laser Transmission Welding of Polycarbonate and Polyamide, Polymer Engineering and Science, 51(5)
Taha Z, Roy G, Hajim K, Manna I (2009) Mathematical modeling of laser-assisted transmission lap welding of polymers. Scr Mater 60(8):663–666
Khosravi S (2010) Laser transmission welding of polybutylene terephthalate and polyethylene terephthalate blends. Queen’s University Kingston, Department of Chemical Engineering, Kingston
Chen M, Zak G, Bates P (2008) Estimating contour laser transmission welding start-up conditions using a novel non-contact method. Weld World 52(11–12):71–76
Jaeschke P, Herzog D, Haferkamp H, Peters C, Herrmann AS (2010) Laser transmission welding of high-performance polymers and reinforced composites—a fundamental study. J Reinf Plast Compos 29(20):3083–3094
Capone C, Di Landro L, Inzoli F, Penco M, Sartore L (2007) Thermal and mechanical degradation during polymer extrusion processing. Polym Eng Sci 47(11):1813–1819
Dong Q, Gao C, Ding Y, Wang F, Wen B, Zhang S, Yang M (2012) A polycarbonate/magnesium oxide nanocomposite with high flame retardancy. J Appl Polym Sci 123(2):1085–1093
Moiseev YV, Markin V, Zaikov GE (1976) Chemical degradation of polymers in corrosive liquid media. Russ Chem Rev 45(3):246
Beyler CL, & Hirschler MM (2002) Thermal decomposition of polymers. SFPE Handbook of Fire Protection Engineering, 2
Vyazovkin S, Burnham AK, Criado JM, Pérez-Maqueda LA, Popescu C, Sbirrazzuoli N (2011) ICTAC kinetics committee recommendations for performing kinetic computations on thermal analysis data. Thermochim Acta 520(1):1–19
Papageorgiou DG, Bikiaris DN, Chrissafis K (2012) Effect of crystalline structure of polypropylene random copolymers on mechanical properties and thermal degradation kinetics. Thermochim Acta 543:288–294
Sengupta R, Sabharwal S, Bhowmick AK, Chaki TK (2006) Thermogravimetric studies on polyamide-6, 6 modified by electron beam irradiation and by nanofillers. Polym Degrad Stab 91(6):1311–1318
Chrissafis K (2009) Kinetics of thermal degradation of polymers. J Therm Anal Calorim 95(1):273–283
Málek J, Mitsuhashi T, Criado JM (2001) Kinetic analysis of solid-state processes. J Mater Res 16(6):1862–1871
Perez-Maqueda L, Criado J, Sanchez-Jimenez P (2006) Combined kinetic analysis of solid-state reactions: a powerful tool for the simultaneous determination of kinetic parameters and the kinetic model without previous assumptions on the reaction mechanism. J Phys Chem A 110(45):12456–12462
Sánchez-Jiménez PE, Pérez-Maqueda LA, Perejón A, Criado JM (2011) Constant rate thermal analysis for thermal stability studies of polymers. Polym Degrad Stab 96(5):974–981
Al‐Mulla A, Mathew J, Al-Omairi L, Bhattacharya S (2011) Thermal decomposition kinetics of tricomponent polyester/polycarbonate systems. Polym Eng Sci 51(11):2335–2344
Saha B, Ghoshal AK (2006) Model-fitting methods for evaluation of the kinetics triplet during thermal decomposition of poly (ethylene terephthalate)(PET) soft drink bottles. Ind Eng Chem Res 45(23):7752–7759
Yao F, Wu Q, Zhou D (2009) Thermal decomposition of natural fibers: global kinetic modeling with nonisothermal thermogravimetric analysis. J Appl Polym Sci 114(2):834–842
Málek J (1992) The kinetic analysis of non-isothermal data. Thermochim Acta 200:257–269
Wang M, Li B, Wang J, Bai P (2011) Preparation and properties of polysiloxane grafting multi-walled carbon nanotubes/polycarbonate nanocomposites. Polym Adv Technol 22(12):1738–1746
Wu T, Chen E, Lin Y, Chiang M, Chang G (2008) Preparation and characterization of melt-processed polycarbonate/multiwalled carbon nanotube composites. Polym Eng Sci 48(7):1369–1375
Li J, Tong L, Fang Z, Gu A, Xu Z (2006) Thermal degradation behavior of multi-walled carbon nanotubes/polyamide 6 composites. Polym Degrad Stab 91(9):2046–2052
Lee J, Liao Y, Nagahata R, Horiuchi S (2006) Effect of metal nanoparticles on thermal stabilization of polymer/metal nanocomposites prepared by a one-step dry process. Polymer 47(23):7970–7979
Zong R, Hu Y, Liu N, Li S, Liao G (2007) Investigation of thermal degradation and flammability of polyamide-6 and polyamide-6 nanocomposites. J Appl Polym Sci 104(4):2297–2303
Mayboudi L, Birk A, Zak G, Bates P (2007) A 3-D thermal model of laser transmission contour welding for a lap joint. Antec-Conf Proc 5:2796
Chen M (2009) Gap bridging in laser transmission welding of thermoplastics. Queen’s University Kingston, Department of Mechanical Engineering, Kingston
Chen M, Zak G, Bates PJ (2009) 3D finite element modeling of contour laser transmission welding of polycarbonate. Weld World 53(7/8):188–197
Mayboudi L, Birk A, Zak G, Bates P (2009) A three-dimensional thermal finite element model of laser transmission welding for lap-joint. Int J Model Simul 29(2):149
Acherjee B, Kuar AS, Mitra S, Misra D (2012) Modeling and analysis of simultaneous laser transmission welding of polycarbonates using an FEM and RSM combined approach. Opt Laser Technol 44(3):995–1006
Potente H, Korte J, Becker F (1999) Laser transmission welding of thermoplastics: analysis of the heating phase. Ronald M.Harris, Editor, 283
Prabhakaran R, Kontopoulou MK, Zak G, Bates PJ, Sidiropoulos V (2005) Simulation of heat transfer in laser transmission welding. Int Polym Proc 20(4):410–416
Hadriche I, Ghorbel E, Masmoudi N, Casalino G (2010) Investigation on the effects of laser power and scanning speed on polypropylene diode transmission welds. Int J Adv Manuf Technol 50(1–4):217–226
Méndez-Liñán L, López-Garzón FJ, Domingo-García M, Pérez-Mendoza M (2010) Carbon Adsorbents from Polycarbonate Pyrolysis Char Residue: Hydrogen and Methane Storage Capacities Energy Fuels, 24(6), 3394–3400
Acknowledgments
The authors would like to thank the NSERC and the NSERC Network for Innovative Plastic Materials and Manufacturing Processes for their financial support of this work, and DSM and Bayer for the materials used in this study. The authors would also like to thank Clarence McEwen of the Royal Military College of Canada (RMCC) for fabricating the test fixture, and John Perreault, also of RMCC, for injection moulding the samples.
Author information
Authors and Affiliations
Corresponding author
Additional information
Doc. IIW-2521, recommended for publication by Commission XVI “Polymer Joining and Adhesive Technology”.
Rights and permissions
About this article
Cite this article
Bates, P.J., Okoro, T.B. & Chen, M. Thermal degradation of PC and PA6 during laser transmission welding. Weld World 59, 381–390 (2015). https://doi.org/10.1007/s40194-014-0209-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40194-014-0209-9