Abstract
The present work has been carried out to establish finite element analysis (FEA) simulation of selective laser melting (SLM) process and validate through experimental results obtained on the powder bed of Ti6Al4V alloy. Process parameters included variable laser power (60–75 W) and scan speed (200–400 mm/min) along with constant parameter and the laser spot diameter of 0.45 mm. Variation in width and depth of melted track was observed through an optical microscope and was compared with FEA results. A code for a nonlinear transient model was developed in ANSYS parametric design language to simulate the process of SLM. It was observed that both the width and depth of the melt pool decrease at high scan speeds and both dimensions increase with power increase. The FEA code developed shows an average deviation of 4.5% in width and 4.65% in depth from the experimental results. The FEA model can be used to establish parameters to obtain specific dimensions of the melt pool in single line scan and optimize the process of SLM by controlling the width and depth of the melt pool.
Similar content being viewed by others
References
Welsch, G.; Boyer, R.; Collings, E.W. (eds.): Materials Properties Handbook: Titanium Alloys. ASM International, Materials Park (1993)
Matsumoto, M.; Shiomi, M.; Osakada, K.; Abe, F.: Finite element analysis of single layer forming on metallic powder bed in rapid prototyping by selective laser processing. Int. J. Mach. Tools Manuf 42(1), 61–67 (2002)
Yadroitsev, I.; Gusarov, A.; Yadroitsava, I.; Smurov, I.: Single track formation in selective laser melting of metal powders. J. Mater. Process. Technol. 210(12), 1624–1631 (2010)
Hussein, A.; Hao, L.; Yan, C.; Everson, R.: Finite element simulation of the temperature and stress fields in single layers built without-support in selective laser melting. Mater. Des. 52, 638–647 (2013)
Kyogoku, H.; Shimizu, Y.; Yoshikawa, K.: Surface morphology of selective laser-melted titanium. In: International Solid Freeform Fabrication Symposium. Austin, Texas, pp. 846–852 (2013)
Fu, C.H.; Guo, Y.B.: 3-Dimensional finite element modeling of selective laser melting Ti–6Al–4V Alloy. In: 25th Annual International Solid Freeform Fabrication Symposium, pp. 1129–1144 (2014).
Shiomi, M.; Yoshidome, A.; Abe, F.; Osakada, K.: Finite element analysis of melting and solidifying processes in laser rapid prototyping of metallic powders. Int. J. Mach. Tools Manuf 39(2), 237–252 (1999)
Contuzzi, N.; Campanelli, S.L.; Ludovico, A.D.: 3D finite element analysis in the selective laser melting process. Int. J. Simul. Model. 10(3), 113–121 (2011)
Dong, L.; Makradi, A.; Ahzi, S.; Remond, Y.: Three-dimensional transient finite element analysis of the selective laser sintering process. J. Mater. Process. Technol. 209(2), 700–706 (2009)
Rihai, M.; Gollo, M.H.; Kalkhoran, S.N.A.: Experimental and numerical study of heat flux distribution in laser forming of bi-layer sheets. J. Comput. Appl. Res. Mech. Eng. 4, 67–79 (2014)
Mandal, V.; Hussain, M.; Kumar, V.; Das, A.K.; Singh, N.K.: Development of reinforced TiN-SS316 metal matrix composite (MMC) using direct Metal laser sintering (DMLS) and its characterization. Mater. Today: Proc. 4(9), 9982–9986 (2017)
Azizpour, M.; Ghoreishi, M.; Khorram, A.: Numerical simulation of laser beam welding of Ti6Al4V sheet. J. Comput. Appl. Res. Mech. Eng. 4, 145–154 (2014)
Boivineau, M.; Cagran, C.; Doytier, D.; Eyraud, V.; Nadal, M.H.; Wilthan, B.; Pottlacher, G.: Thermophysical properties of solid and liquid Ti–6Al–4V (TA6V) alloy. Int. J. Thermophys. 27(2), 507–529 (2006)
Popovich, A.; Sufiiarov, V.: Metal powder additive manufacturing. In New Trends in 3D Printing. InTech (2016).
Verhaeghe, F.; Craeghs, T.; Heulens, J.; Pandelaers, L.: A pragmatic model for selective laser melting with evaporation. Acta Mater. 57(20), 6006–6012 (2009)
Hussain, M.; Kumar, V.; Mandal, V.; Singh, P.K.; Kumar, P.; Das, A.K.: Development of cBN reinforced Ti6Al4V MMCs through laser sintering and process optimization. Mater. Manuf. Process. 32(14), 1667–1677 (2017)
Kundu, S.; Hussain, M.; Kumar, V.; Kumar, S.; Das, A.K.: Direct metal laser sintering of TiN reinforced Ti6Al4V alloy based metal matrix composite: fabrication and characterization. Int. J. Adv. Manuf. Technol. 97, 1–12 (2018)
Lü, L.; Fuh, J.; Wong, Y.S.: Laser-Induced Materials and Processes for Rapid Prototyping. Springer, Berlin (2013)
Kruth, J.P.; Levy, G.; Klocke, F.; Childs, T.H.C.: Consolidation phenomena in laser and powder-bed based layered manufacturing. CIRP Ann. Manuf. Technol. 56(2), 730–759 (2007)
Gu, D.; Shen, Y.: Balling phenomena in direct laser sintering of stainless steel powder: metallurgical mechanisms and control methods. Mater. Des. 30(8), 2903–2910 (2009)
Hussain, M.; Mandal, V.; Kumar, V.; Das, A.K.; Ghosh, S.K.: Development of TiN particulates reinforced SS316 based metal matrix composite by direct metal laser sintering technique and its characterization. Optics Laser Technol. 97, 46–59 (2017)
Gupta, A.; Hussain, M.; Misra, S.; Das, A.K.; Mandal, A.: Processing and characterization of laser sintered hybrid B4C/cBN reinforced Ti-based metal matrix composite. Opt. Lasers Eng. 105, 159–172 (2018)
Acknowledgement
Support from IIT (ISM), Dhanbad, is gratefully acknowledged.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Hussain, M., Gupta, P., Kumar, P. et al. Selective Laser Melting of Single Track on Ti–6Al–4V Powder: Experimentation and Finite Element Analysis. Arab J Sci Eng 45, 1173–1180 (2020). https://doi.org/10.1007/s13369-019-04263-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13369-019-04263-1