Abstract
Subsea production system has been increasingly used in recent South China Sea offshore developments. With deepwater applications, constituent parts of subsea systems become more complicated and enlarged. Increases on the weight and geometry of each component bring challenges to installations. A recent accomplished deployment on a subsea massive jumper shows the weight and length have been up to 120 tons and 90 m, respectively with sophisticated geometry. It is considerably difficult to install heavy and large subsea structures, especially in South China Sea where severe environmental conditions are common. In addition, deepwater deployment may alter natural frequency of the hoisting system and the altered frequency may be close to possible environmental conditions. To deal with the above two issues, traditionally, engineers need to carry out series of complicated numerical analyses which are on case basis and significantly time-consuming. Existing studies focus on the optimization on analysis techniques by conducting laboratory testing and numerical simulations. However, easy-to-use guidance on massive subsea structure installation are somewhat limited. The studies presented in this paper aim to achieve a simplified guidance which can briefly screen the cases subject to axial resonance and provide visible correlations between hoisting system integrity and key installation parameters.
Similar content being viewed by others
References
DNV, 2011. Modelling and Analysis of Marine Operation, DNV-RPH103.
Galgoul, N.Z., Labanca, E.L. and Claro., C.A., 2001. Experience gained during the istallation design of the poncador manifold in a 1860 m water depth, Proceedings of the 20th International Conference on Ocean, Offshore and Arctic Engineering, Rio de Janeiro, Brazil, Paper No. OMAE 2001/OTF-1063.
Kimiaei, M., Xu, J.J. and Yu, H., 2009. Comparing the results of a simplified numerical model with DNV guidelines for installation of subsea platforms, Proceedings of the 28th International Conference on Ocean, Offshore and Arctic Engineering, Honolulu, Paper No. OMAE 2009-79356.
Legras, J.L. and Wang, J., 2011. Criteria for the operation of lowering a structure to the seabed based on the installation vessel motion, Proceedings of 2011 Offshore Technology Conference, Houston, Paper No. OTC-21250-MS.
Roveri, F.E. and De Oliveira, M., 1996. Installation of a production manifold in 2000 ft water depth offshore brazil, Proceedings of 1996 Offshore Technology Conference, Houston, Paper No. OTC-8237-MS.
Sekita, K., Kimura, H. and Tatsuta, M., 1986. Dynamic lifting analysis of offshore structures, Proceedings of 1986 Offshore Technology Conference, Houston, Texas, Paper No. OTC-5287-MS.
Sun, G.M., Wang, F.C., Zhang, Y.G., Tang, K. and Wang, J., 2015. A generic study on lowering analysis of massive jumper structures though the splash zone, Proceedings of the ASME 29th International Conference on Ocean, Offshore and Arctic Engineering, Newfoundland, Canada, Paper No. OMAE2015-41055.
Wang, J., Hagen, R.K., Radan, E. and Bullock, J., 2011a. Technical challenges and success for rigid pipeline with PLET, jumper and flying leads installation in conger 9 field, Proceedings of 2011 Offshore Technology Conference, Houston, Paper No. OTC-21209-MS.
Wang, Y.Y., Duan, M.L., Wang, F., Wang, D.G., Liu, J.P. and Zeng, K.Y., 2011b. Investigation on installation methods of deepwater manifolds and their applications to LW3-1 gas field in South China Sea, The Ocean Engineering, 29(3), 22–30. (in Chinese)
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Wang, Fc., Wang, J. & Tang, K. A finite element based study on lowering operation of subsea massive structure. China Ocean Eng 31, 646–652 (2017). https://doi.org/10.1007/s13344-017-0074-6
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13344-017-0074-6