Abstract
Sour gas reservoirs have faced critics for environmental concerns and hazards, necessitating a novel outlook to how the produced sour gases could be either utilized or carefully disposed. Over the years of research and practice, several methods of sour gas processing and utilization have been developed, from the solid storage of sulfur to reinjecting the sour gas into producing or depleted light oil reservoir for miscible flooding enhanced oil recovery. This paper seeks to investigate the impact of injection parameters on the performance of sour gas injection for enhance oil recovery. In designing a miscible gas flooding project, empirical correlations are used and the key parameter which impacts the phase behavior is identified to be the minimum miscibility pressure (MMP). A compositional simulator was utilized in this research work to study the effect of injection parameters such as minimum miscibility pressure, acid gas concentration, injection pressure and injection rate on the performance of miscible sour gas injection for enhanced oil recovery. The findings showed that methane concentration had a significant impact on the MMP of the process. Additionally, an increase in acid gas concentration decreases the MMP of the process as a result of an increase in gas viscosity, consequently extending the plateau period resulting in late gas breakthrough and increased overall recovery of the process.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
Introduction
A major cause for concern in the development of sour gas reservoir is the disposal of the produced gas (Xue et al. 2019). The gases are usually sweetened using different methods. Amine extraction is one of the most commonly used methods in the petroleum industries (Bennion et al. 1999; Chen 2016). The separation process results in the production of a waste stream composing of acid gases (CO2 and H2S) and requires a huge capital and operation cost which has raised a cause of concern, given that the companies must ensure their waste is eco-friendly before disposal (Bennion et al. 1999).
Over the years, a lot of strategies have been developed to handle acid gas mixture, with primary concerns being the reduction of the toxic hydrogen sulfide gas to an inert/non-toxic reactive product (Bennion et al.1999). The most common technique is the Claus reaction process where gases containing H2S are catalytically converted to elemental sulfur (Bennion et al. 1999). Also, a viable alternative is the reinjection of the produced gas into the reservoir as an enhanced recovery technique or for storage (Abou-Sayed et al. 2004; Bhatti et al. 2019; Ceragioli and Gianelli 2008; Ghoodjani and Bolouri 2011; Hawez and Ahmed 2014; Nwidee et al. 2016). However, concerns have been raised as to possible leakages to the surfaces through faults or unsealing traps.
Sour gas injection for enhance oil recovery (EOR) is a viable option that presents a solution to many problems currently in the industry. It eliminates current taxation or future liability associated with emission or surface storage of sulfur (Abou-Sayed et al. 2004). EOR programs using gas injection have shown that sour gas has better sweep efficiency and voidage replacement ability compared to other gases used for miscible injection EOR. Therefore, this increases the amount of recoverable hydrocarbon (Abou-Sayed et al. 2004; Al-Hadhrami et al. 2007; Battistelli et al. 2011; Chugh et al. 2006; Metcalfe et al. 1973). This also translates to better economics as the cost of many surface treatments is eliminated, thus reducing the operational cost of the process.
This research work seeks to provide insight into the impact of injection parameters on the viability of miscible flooding of a light oil reservoir by the reinjection of sour gas (Abou-Sayed et al. 2004; Benham et al. 1960; Christiansen and Haines 1987; Eakin 1988; Elsharkawy et al. 1992; Green and Willhite 1998; Haynes et al. 2008; Holm and Josendal 1974; Khan et al. 2013; Lake 1989; Orr and Silva 1987; Orr et al. 1982). The reinjection of a rich waste acid gas stream directly into the producing light oil reservoir for the purpose of miscible flooding enhanced oil recovery using numerical simulation was studied putting into consideration the impact of certain injection parameters on the overall performance of the recovery process.
Methodology and model description
This section presents the reservoir model description, detailed methodologies and procedures used in achieving the aim and objectives of this research work. A comparative study of MMP using correlations was carried out. Base case light oil reservoir model was built using Eclipse 300 which is a compositional simulator, and the performance of sour gas injected was evaluated by varying the composition of acid gas injected in the oil recovery. The effect of the gas injection rate and injection parameter on the field production was also studied.
Base case model description
The reservoir model used in this study was based on the reservoir studies carried out by Battistelli et al. 2011. The fluid composition, porosity and initial water saturation are the same as reported. Other parameters such as permeability, grid, reservoir pressure and temperature were assumed. The base case model is a homogeneous reservoir with both porosity and permeability uniform in all directions, and the model was built using ECLIPSE 300 which is a compositional simulator. The model consists of two wells, one producer and one injector. The base case model has a length of 1320 ft, a width of 1320 ft and a thickness of 10 ft, and major reservoir parameters are summarized in Table 1. Peng–Robinson EoS is used in fluid characterization, and the component properties are summarized in Table 1. The injection fluid composition is shown in Table 2.
Reservoir model initialization
The reservoir model was initialized to determine the initial conditions of the reservoir. The gas–oil contact was set far above the reservoir so that only the hydrocarbon content is considered for study; the water–oil contact is set at 100 ft below the reference depth. Table 3 shows the reservoir model input parameters, while Table 4 shows the phase binary interaction parameters for the components contained in the oil mixture. Table 5 shows the oil, water and gas saturation functions.
Comparative study of MMP using correlations
This study made use of the existing pure and impure CO2 stream MMP correlations published in the literature. Three injection scenarios (Table 6) were considered to evaluate the general trend on how MMP changes with a decrease in C1 composition.
First scenario
In this scenario, the injection gas consists of only CO2 and C1. Two different correlations used in this case were Yuan et al. correlation and Glaso correlation. MMP was calculated as C1 composition decreases and CO2 composition increases. MMP for pure CO2 was calculated first using the two correlations: For Glaso correlation, the MMP is a function of reservoir temperature and intermediate component composition in the reservoir oil (C2–C6) (Glaso 1985), while for Yuan et al. correlation, the MMP is a function of the molecular weight of C7+, molar percentage of intermediates and reservoir temperature. The limitation of this correlation is that the oil used for the regression has a molecular weight of C7+ in the range of 140–245, whereas the oil in the reservoir studied has MC7+ of 250. Also, the molar percentage of the intermediates is between 11.3 and 40.3% and reservoir temperature ranges from 120 to 300 °F (Yuan et al. 2004). The fraction of impure and pure MMP is calculated using the Yuan et al. correlation from which the impure MMP for the two correlations was calculated.
Second scenario
In this case, the injection gas consists of three components as listed in Table 6. The injection gas composition changes by decreasing C1 and increasing H2S and CO2 compositions. CO2 and H2S compositions were increased equally. Two correlations were used for this study: Yuan et al. and Glaso correlation for the estimation of pure CO2 MMP; for the impure/pure MMP fraction, Sebastian et al. and Yuan et al. were used, while the impure MMP was calculated using Glaso and Yuan et al. correlation.
Third scenario
In this case, only H2S and C1 are present in the injection gas. The goal here is to understand how H2S affects the MMP. Correlation for estimating hydrocarbon gas MMP and impure CO2 stream was used to calculate the MMP. The Glaso correlation for hydrocarbon gas is the best option because it accounts for the change in C1 composition in the injected gas which corresponds to the objective of this study. The Yuan et al. correlation was used for the impure CO2 stream for comparison purpose.
Compositional variation of acid gas in the injection gas
It is important to determine how acid gas composition in the injection gas affects oil recovery as this will help to understand how the gas helps to improve recovery in a gas injection process. A 15-mole percent acid gas is used for the base case model with an equal composition for H2S and CO2 (i.e., 7.5% of H2S and 7.5% CO2). C1 makes up 80% of the injection gas, 0.0061% water, while C2–C5 makes up the remaining percentage as shown in Table 6. The composition of acid gas was varied subsequently from 15–20%, 30% and 40%. Also, three different cases were further considered to see the effect of injecting pure CO2 (case one), a mix of 50% acid gas and 50% C1 (case two) and pure acid gas having 50% CO2 and 50% H2S (case three) on the oil production rate and recovery efficiency, respectively, considering miscibility conditions.
Effect of gas injection rate
This study helps to also understand how gas injection rate affects various parameters such as oil recovery, oil production rate and how the volume of gas injected increases oil recovery. For this study, three rates were used to compare with the base case model. The injection was changed from 500 to 3000 Mscf to compare with the base case of 2000 Mscf.
Injection pressure effect
In this part of the study, the effect of injection pressure on the oil recovery from the model was investigated. Injection and production wells are completed in the first and fifth layer, respectively. For this investigation, two different pressures were used representing low case and high case to compare with the base case model.
For low case, an injection pressure of 2500 psia was used. This pressure was used to simulate immiscible gas injection, while for the high case, an injection pressure of 7500 psia was used which simulates first contact miscible injection. Based on the MMP study done, the estimated MMP using the equation of state analytical method in Eclipse PVTi is approximately 6200 psia for first contact miscibility and 5000 psia for multi-contact miscibility. Simulation runs were conducted at pressures below, equal to and greater than this pressure as stated above.
Since in vaporizing drive mechanisms, the pressure at the miscible front should be greater than the predicted miscible pressure, injection of gas at 5200 psi will raise the average reservoir pressure from initial pressure to the miscibility pressure of 5000 psi. Therefore, the injection pressure of 5200 psi seems to be the best candidate for the base case model.
Results and discussions
Comparative study of MMP using correlations
First scenario
The fraction of impure and pure MMP was calculated using the Yuan et al. correlation and Glaso correlation from which the impure MMP for the two correlations was calculated as seen in Table 7. Both correlations gave a similar trend; the MMP decreases as C1 composition decreases as shown in Figs. 1 and 2. The decrease in the MMP as methane composition increased was due to the nature of t methane gas. It is lighter and has a low viscosity. It will form a lesser density gas mixture. Utilization of only methane gas requires a very high MMP to attain miscibility for oil trapped in already depleted reservoir. But mixing it with CO2 will lower the MMP required. This is indeed the very reason why there is a decrease in the MMP as the concentration of methane in the injection gas increases.
Second scenario
Table 8 shows the result of the MMP studies obtained from scenario two, while Figs. 3 and 4 show the results of the second scenario MMP study using the Glaso correlation and Yuan et al. correlation, respectively. Both figures show a linear relationship between C1 composition and MMP. This scenario shows a trend similar to the first scenario which further confirms the effect of C1 on MMP. Just as in the first scenario, the Glaso correlation has a more conservative result as compared to Yuan et al. correlation. Comparing the result of the two scenarios, the MMP of the second scenario is higher which is due to the presence of H2S. CO2 is denser than H2S, and the addition of H2S leads to an increment in the MMP as compared to scenario one. Similarly, an increment of the percentage of methane leads to an increment in the MMP.
Third scenario
Table 9 shows the results of the MMP studies obtained from scenario three, while Figs. 5 and 6 show the MMP trend for the third scenario using the Glaso correlation and Yuan et al. correlation, respectively. It is seen that the Glaso correlation gave a more realistic MMP as compared to Yuan et al. correlation. The MMP values obtained using the Yuan et al. correlation were higher than the ones obtained in scenario one and scenario two making it unrealistic. This is because Yuan et al. correlation is designed for a CO2 stream with impurities which is not true for this case. However, the MMP trend obtained for this scenario using the Glaso correlation and Yuan et al. correlation was a parabolic trend unlike scenario one and scenario two where the trend obtained was a linear trend. This could be associated with the fact that both correlations used are not a perfect match for the case under investigation. The Glaso correlation is designed for gas injection with intermediates component (C2–C6) of molecular weight of 34 which is not the case here. The MMP also increased with reduction in the composition of methane due to the nature and density of methane as observed in the first scenario.
Base case model description and initialization
The base case reservoir model used in this study is shown in Fig. 7. From the model initialization result, the initial field pressure of the reservoir was 5169 psi at a reference depth of 9840 ft, which corresponds to the top of the reservoir. From Table 3, a simple calculation shows that the reservoir has a pore volume of 620,160 rb, with an initial hydrocarbon pore volume of 496,128 rb. The original oil in place, water in place and gas in place were 216050 STB, 124,128 rb and 570.803 Mscf, respectively. The reservoir has an initial GOR of 2.642 Mscf/STB and FVF of 2.298 rb/STB.
Compositional variation of acid gas in the injection gas
Figure 8 shows the effect of acid gas compositional variation on oil recovery efficiency. The result shows that the increase in acid gas concentration leads to an increase in oil recovery. An overall recovery of 86.81 and 78% was achieved when 40.30% and 20% acids gas composition, respectively, were used. It is also observed that the injection gas with the lower composition of acid gas had the earliest breakthrough time, while the injection gas with the highest composition had the least breakthrough time. The increase in the recovery of oil and delay of the breakthrough time as the composition of the acid gas was increased was as a result of the increment in the density and viscous nature of the injection gas. The acid gas increased the density and viscosity of the injected gas.
Figure 9 shows how acid gas composition affects oil production rate. The result clearly shows that as the composition of acid gas increases the gas breakthrough time also increases. Initially, there was a decrease in the oil production rate, but after about 40 days of injecting the sour gas, the reservoir began to feel the effect of the injection leading to an increment in the production rate. The injection gas with 15% acid gas composition had the least breakthrough time, and the injection gas with 40% acid gas had the highest breakthrough time. This is because as the composition of acid gas increases in the injection gas, the viscosity of the injection gas also increases leading to a decrease in the mobility of the injected gas.
Figure 10 shows the effect of acid gas composition on the oil production rate. The first down dip is when the reservoir is producing under natural depletion before injection starts. For the base case, as the pressure support starts at around day 100, there is a plateau gas production, while for 40% acid gas, the gas production did not stabilize until the gas breakthrough. Figure 11 shows the change in gas viscosity with the increased acid gas concentration. This gives a clearer picture of the production profile of both gas and oil. This figure shows that the gas viscosity increases as acid gas concentration is increased. The increase in gas viscosity is the consequence of miscible development resulting in a reduction of oil viscosity.
This reduction is the result of oil swelling or expansion of the under-saturated fluid by the addition of dissolved gas at higher pressures, which lightens the oil and consequently decreases the oil viscosity. This is why 40% of the acid gas profile did not reach a plateau production until gas breakthrough. As a result, more gas dissolving in oil means less gas is coming out of solution.
Figures 12 and 13 show the oil production rate and recovery efficiency, respectively, for the different cases of injection gas compositions that were also considered. Case one was when only pure CO2 was injected into the reservoir. When compared to the base case scenario, there was a 14.38% increase in the oil recovery efficiency. There was also an increase in the plateau period for the production rate profile, and this was due to the increase in the injection gas viscosity. For case two, the injection gas contains only C1 (50%) and acid gas (50%). With the decrease in the C1 composition in the injection gas as compared to the base case, there was 13.40% increase in the oil recovery. This was due to the increase in the injection gas viscosity, and as a result of this, it led to an increase in the sweep efficiency. The increase in the viscosity of the injection gas increased the plateau production period by 50 days as compared to the base case scenario.
Case three was characterized with the injection of pure acid gas into the reservoir with CO2 and H2S having equal proportion (50% CO2 and 50% H2S). This case had same recovery efficiency like when only pure CO2 was used. It had a recovery of about 91%. But due to the viscous nature of acid gas, this case had a longer plateau period as compared to case one when only pure CO2 injection was carried out which resulted in an increase in the aerial sweep efficiency. Another advantage of this was that the acid gas achieved miscibility with the reservoir oil at lower pressure as compared to the pure CO2 injection case.
Effect of gas injection rate
Figure 14 shows how the gas injection rate affects oil production rate. It was observed that there was an early gas breakthrough for rate 2000 and 3000 Mscf. This could be due to the increase in driven force as the injection rate increases. There was no noticeable change when the injection rate increased above 2000 Mscf. This is because the injection well is constrained using two parameters (injection rate and pressure). Figure 15 shows the injection rate builds up over time. From the result, it is seen that the rate is gradually building up to the constrained rate and maintained throughout the simulation time for 500 Mscf and 1000 Mscf, while for 2000 and 3000 Mscf, the rate gradually builds up until the pressure support kicks in. But the rate does exceed 1500 Mscf which is maintained until the gas breakthrough after which rate starts declining until it reaches 1000 Mscf. This further shows that the current injection pressure does not support any rate above 1500 Mscf. The rate of decline in the oil production rate observed after breakthrough was due to the decrease in the pressure support.
Figure 16 is used to investigate how the volume of gas injected affects oil recovery efficiency. The result clearly shows that the volume of gas injected is directly proportional to oil recovery efficiency. The result is consistent with the findings of Comberiati and Zammerilli (2000) which also showed an increment in oil production with increasing flood volume.
Injection pressure effect
Figure 17 shows the effect of gas injection pressure on oil recovery efficiency. It is clearly seen that there is an incremental oil recovery as a result of an increase in injection pressure. This increment in recovery is attributed to the fact that the higher the injection pressure, the more the tendency to attain miscibility. A noticeable change was observed due to the fact that the reservoir attained miscibility as the injection pressure was increased beyond 2500 psi. Figure 18 shows the oil production rate for different injection pressures. It is seen that the attainment of miscibility and increment in the injection pressure lead to an increment in the production rate. According to the figure, for the high case, the pressure support was almost immediate, while for the base case, the pressure support did not kick in until 52 days of continuous gas injection. The high case shows an early breakthrough time, but the difference as compared with the base case is marginal which further supports the argument that the economy may not support the incremental recovery from the high case.
Figure 19 shows the gas injection rate at different injection pressures. The figure shows how injection pressure affects the gas injection rate. For the high case model, a rate of 2000 Mscf was maintained until the gas breakthrough. After that, there was a steady decline in the rate until it reached 1000 Mscf. This effect was seen during the injection rate study which further proves that the injection rate is directly proportional to injection pressure. This is due to the fact that high injection pressure means the driven force is high which translates to high gas velocity. It shows that for this study, the 1000 Mscf rate is the optimal injection rate.
Conclusion
-
In conclusion, sour gas injection for enhanced oil recovery has supreme performance as compared to other gases used for miscible gas flooding EOR.
-
Acid gas lowered the MMP of the process significantly resulting in more oil recovery and low operational cost for the process.
-
Injection parameters such as the minimum miscibility pressure, acid gas concentration, injection pressure and injection rate had effect on the overall performance of the recovery process.
-
The success of the miscible sour gas injection EOR can be attributed to the variation in fluid viscosities toward lower mobility ratios during injection. The injection gas lowers the oil viscosity substantially. This reduction is as the result of oil swelling or expansion of the under-saturated fluid by the addition of dissolved gas at higher pressures, which lightens the oil and consequently decreases the oil viscosity.
-
The increase in the acid gas composition led to an increase in the oil recovery efficiency and the gas breakthrough time.
References
Abou-Sayed AS, Zaki K, Summers C (2004) Management of sour gas by underground injection—assessment, challenges and recommendations. SPE Soc Pet Eng. https://doi.org/10.2118/86605-ms
Al-Hadhrami AK, Darrell DW, Deinum G, Harry S (2007) The design of the first miscible sour gasflood project in Oman. In: IPTC: international petroleum technology conference. https://doi.org/10.2523/iptc-11396-ms
Battistelli A, Ceragioli P, Marcolini M (2011) Injection of acid gas mixtures in sour oil reservoirs: analysis of near-wellbore processes with coupled modelling of well and reservoir flow. Transp Porous Med 90(1):233–251. https://doi.org/10.1007/s11242-010-9685-6
Benham AL, Dowden E, Kunzman JW (1960) Miscible fluid displacement-prediction of fluid miscibility. Pet Trans AIME 219:8
Bennion DB, Thomas FB, Bennion DW, Bietz RF (1999) Formation screening to minimize permeability impairment associated with acid gas or sour gas injection/disposal. In: Annual technical meeting, Petroleum Society of Canada. https://doi.org/10.2118/99-13-56
Bhatti AA, Raza A, Mahmood SM et al (2019) Assessing the application of miscible CO2 flooding in oil reservoirs: a case study from Pakistan. J Pet Explor Prod Technol. https://doi.org/10.1007/s13202-018-0504-x
Ceragioli P, Gianelli G (2008) Alteration of thermodynamic equilibria and fluids-rock interactions during acid gas injection into a carbonate sour oil reservoir. SPE Soc Pet Eng. https://doi.org/10.2118/113920-ms
Chen, Z, Liao X, Zhao X, Chen C, Zhu L, Zhang F, Mu L, Zhou X (2016) Optimization of injection and production parameters for sour gas storages: a case study. In: OTC: offshore technology conference. https://doi.org/10.4043/26686-ms
Christiansen RL, Haines K (1987) Rapid measurement of minimum miscibility pressure with the rising-bubble apparatus. SPE Reserv Eng. https://doi.org/10.2118/13114-pa
Chugh S, Behrend J, McKishnie RA (2006) Development of the Strasshof Tief sour gas field including acid gas injection into adjacent producing sour gas reservoirs. In: SPE Europec/EAGE annual conference and exhibition. SPE: Society of Petroleum Engineers. https://doi.org/10.2118/100328-ms
Comberiati JR, Zammerilli AM (2000) Effects of petroleum-reservoir conditions on oil recovery by carbon dioxide injection; DOE/METC/TPR-83-4 (DE83008455); U.S. Department of Energy: Morgantown, WV, USA
Eakin, BE, Mitch FJ (1988) Measurement and correlation of miscibility pressure of reservoir oil. In: SPE annual technical conference and exhibition, Houston. SPE
Elsharkawy AM, Poettmann FH, Christiansen LR (1992) Measuring minimum miscibility pressure: slim-tube or rising-bubble method? In: SPE/DOE enhanced oil recovery symposium. SPE: Society of Petroleum Engineers. https://doi.org/10.2118/24114-ms
Ghoodjani E, Bolouri SH (2011) Experimental study of CO2-EOR and N2-EOR with focus on relative permeability effect. J Pet Environ Biotechnol 2:106. https://doi.org/10.4172/2157-7463.1000106
Glaso O (1985) Generalized minimum miscibility pressure correlation (includes associated papers 15845 and 16287). https://doi.org/10.2118/12893-pa
Green DW, Willhite PG (1998) Enhance oil recovery, SPE. SPE, USA
Hawez H, Ahmed Z (2014) Enhanced oil recovery by CO2 injection in carbonate reservoirs. WIT Trans Ecol Environ 186:547–58. https://doi.org/10.2495/esus140481 (PDF) Efficiency of enhanced oil recovery by injection of low-salinity water in barium-containing carbonate reservoirs. https://www.researchgate.net/publication/326425502_Efficiency_of_enhanced_oil_recovery_by_injection_of_low-salinity_water_in_barium-containing_carbonate_reservoirs. Accessed 14 Feb 2019
Haynes B, Kaura NC, Faulkner A (2008) Life cycle of a depletion drive and sour gas injection development: Birba A4c Reservoir, South Oman. In: IPTC: international petroleum technology conference. https://doi.org/10.2523/iptc-12175-ms
Holm LW, Josendal VA (1974) Mechanisms of oil displacement by carbon dioxide. J Pet Technol 26(12):1427–1438. https://doi.org/10.2118/4736-pa
Khan C, Amin R, Madden G (2013) Effects of Co2 and acid gas injection on enhanced gas recovery and storage. J Pet Explor Prod Technol 3(1):55–60. https://doi.org/10.1007/s13202-012-0044-8
Lake LW (1989) Enhanced oil recovery. Prentice-Hall, Englewood Cliffs
Metcalfe RS, Fussell DD, Shelton LJ (1973) A multicell equilibrium separation model for the study of multiple contact miscibility in rich-gas drives. Soc Pet Eng J 13:147–155. https://doi.org/10.2118/3995-pa
Nwidee LN, Theophilus S, Barifcani A, Sarmadivaleh M, Iglauer S (2016) EOR processes, opportunities and technological advancements. Chem Enhanc Oil Recov Pract Overv. https://doi.org/10.5772/64828
Orr FM, Silva MK (1987) Effect of oil composition on minimum miscibility pressure—part 2: correlation. SPE Reserv Eng 2:479–491. https://doi.org/10.2118/14150-pa
Orr FM, Silva MK, Lien CL, Pelletier MT (1982) Laboratory experiments to evaluate field prospects for CO2 flooding. J Pet Technol 34:888–898
Xue Y, Vo M, Yu Y, Singleton F, Zhang J (2019) Water disposal management in a sour gas field development in Sichuan. In: Shemwell S, Lin J (eds) Proceedings of the international petroleum and petrochemical technology conference 2018. IPPTC 2018, Springer, Singapore
Yuan H, Johns RT, Egwuenu AM, Dinoruk B (2004) Improved MMP correlations for CO2 floods using analytical gas flooding theory. Paper SPE 89359 presented at SPE/DOE fourteenth symposium on improved oil recovery held in Tulsa, Oklahoma, USA, April 17–21
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Kaita, A.Y., Ogolo, O., Wu, X. et al. Study of the impact of injection parameters on the performance of miscible sour gas injection for enhanced oil recovery. J Petrol Explor Prod Technol 10, 1575–1589 (2020). https://doi.org/10.1007/s13202-019-00793-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13202-019-00793-4