Abstract
Enhanced oil recovery methods are the future of maximizing oil recoveries. Any incremental oil recovery can support the world economy by producing more oil at a minimum price. The surfactants are the major constituent of the injection fluids for EOR applications. Addition of foam-generated surfactants in water alternating gas injection is one of the potential solutions for reducing the gas mobility and improving sweep efficiency, but the major challenge of surfactants used with water alternating gas injection is its stability in presence of formation water and crude oil at reservoir conditions. The objective of this study is to investigate the stable surfactant as a foaming agent to improve the efficiency of residual oil and reduce the gas mobility. To achieve this main objective, individual and new surfactant blended formulations were evaluated with injection water and crude oil in the porous media at 96 °C and 1400 psi. Experimental result showed that generated foam in presence of crude oil has reduced gas mobility which provides good indication of CO2 mobility control and improves sweep efficiency. Oil recovery based on original oil-in-place by surfactant blend of 0.6 wt% AOS + 0.6 wt% TX 100, 0.6 wt% AOS + 0.6 wt% LMDO and individual surfactant of 0.6 wt% AOS were recorded as 91.9, 83.7 and 72.66%, respectively. Foam stability in presence of crude oil, reduction in gas mobility and increase in oil recovery indicated that these surfactant blends are good foaming agents as compared to individual surfactant in enhanced oil recovery applications.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Avoid common mistakes on your manuscript.
Introduction
The first reported water alternating gas (WAG) field pilot was implemented in the North Pembina field, Alberta, Canada in 1956–1957 (Algharaib et al. 2007; Nadeson 2004). At present, the WAG injection process has been applied in oil fields of USA, Canada, Malaysia, Norway and some other countries of the World. In this process, mainly CO2 or combination of CO2 and produced hydrocarbon gases are injected at miscible or immiscible conditions. However, WAG injection process suffers by gravity segregation and viscous fingering mostly in heterogeneous reservoirs (Rogers and Grigg 2000). Therefore, the incremental oil recovery during WAG injection remains low. Controlling the mentioned problems in water alternating gas injection, addition of foam (surfactants) in brine water is more efficient. Foam-generating surfactants flooding has been paid more attention in enhanced oil recovery (EOR) methods due to its unique properties of oil displacement and gas mobility control (Svorstol et al. 1996; Wang et al. 2009). The method has attracted increasing attention of oil industries and research institutions. The performed theoretical and experimental studies, pilot tests and field application showed that the foam used as gas mobility control can improve the EOR process. The foam stability at reservoir conditions in the North Sea, Daqing oil and other fields proved the potential of this method (Feng et al. 2009; Vikingstad et al. 2006; Wang et al. 2006).
Foam injection in oil reservoir was first proposed by Bond and Holbrook and reported by Bernard and Holm in 1965 (Boud and Holbrook 1958; Bernard and Jacobs 1965). Foam is defined as a dispersed system consisting of bubbles that are separated by foam film and plateau boarders (Karakashev and Grozdanova 2012). In porous media, foam surfactants are used in near wellbore flow treatments such as foam–acid matrix stimulation and plugging of unwanted phases (Chang et al. 2002; Wassmuth et al. 2004), in fractured fluids (Blauer and Kohlhaas 1974; Wheeler 2010), in shallow subsurface environmental remediation (Hirasaki et al. 1997; Mamun et al. 2002; Hirasaki 1989) and in EOR processes to control the gas mobility and overcome in situ permeability variations (Blaker et al. 2002). This method can be applied by simultaneously injecting gas and surfactant solution or alternating gas with brine-added surfactant solution (Dholkawala et al. 2007).
The world’s largest foam application was implemented successfully on the Snorre field. The main purpose of foam was used with WAG injection process as gas mobility reduction. The field is located in Norwegian sector of the North Sea, about 200 km northwest of Bergen. A foam injection was started in July 1996. AOSC14-16 was used during foam cycle with 1–2 wt% concentration. 50% GOR was reduced for 2 months. Gas injectivity was reduced during the first and second gas cycle. This is because of foam generated and because the foam zone extended during first and second gas cycle (Sheng 2013). The important experience by this project is the good understanding of foam behavior at the target reservoir conditions that led to good planning and successful field application (Farzaneh and Sohrabi 2013).
In recent years, many foaming agents were selected and studied to achieve the best foam stability in presence of crude oil (Al-Attar 2011; Kovscek et al. 2010; Deng et al. 2012; Ashoori et al. 2011; Lai and Chen 2008; Cubillos et al. 2012). Most of the research has been carried out on individual (single) surfactant as a foaming agent, but has neglected the effect of blend of foam surfactant system. Surfactants are the major constituent of the injection fluids for EOR applications. In this research study, we used consolidated Berea sandstone core samples to perform core flooding experiments in order to examine the effectiveness of surfactant blended formulations at reservoir conditions. Blend of surfactant solutions synergistically exhibits better foaming properties and will open new opportunities to produce more residual oil from depleting oil reservoirs. This research focuses on the study of individual and blend of foam surfactants as a foaming agent that has better gas mobility reduction and thus improving overall efficiency of residual oil.
Experimental work
Materials
Foam surfactant
Three commercially available surfactants were used to perform the experiments. Alpha olefin sulfonate (AOSc14–16) and lauramidopropyl amine oxide (LMDO) were supplied by Stepan Company, USA. Octylphenol ethoxylate surfactant (Triton TX-100) was purchased from Sigma-Aldrich. The molecular weight of each surfactant is known. All surfactant were used as received without further treatment.
Synthetic brine (injection water)
Sodium chloride (NaCl) was purchased from Fischer Company, UK, magnesium chloride (MgCl2·6H2O), potassium chloride (KCL), sodium bicarbonate (NaHCO3), sodium sulfate (Na2So4) and calcium chloride (CaCl2·2H2O) were purchased from R & M Chemicals, UK. The field-related brine with 34107 ppm was synthesized in the laboratory and used as injection water. Table 1 presents the composition of injection water.
Crude oil
Crude oil was collected from oil field offshore Malaysia. The density was measured as 0.7886 g/cc (49.2307Ib/ft3) at 96 °C and 1400 psi by Anton Paar density meter. The oil viscosity was measured as 1.591cp at 96 °C and 1400 psi by HTHP EV-1000 viscometer. The specific gravity of crude oil is 0.7889, and degree API is 37.7.
CO2 gas
CO2 gas was selected due to its miscibility/partial miscibility with many hydrocarbon components of crude oil at reservoir conditions. Gas viscosity at 96 °C was calculated by Sutherland’s equation. This equation is based on kinetic theory of ideal gases (http://www.lmnoeng.com).
For CO2 gas, \(\mu_{o} =\) reference viscosity at reference temperature, 0.01480cp, \(T_{o} =\) reference temperature, 527.6°R, and C = Sutherland constant, 240.
Density of CO2 gas was calculated at 96 °C and 1400 psi by using the following formula. Properties of CO2 gas are presented in the Table 2.
where\(\uprho_{{{\text{CO}}_{2} }} = {\text{Density of gas, }}\text{Ib}/\text{ft}^{\text{3}} ,\) M a apparent molecular weight of gas, P = pressure, psi, R = gas constant, T = temperature, °R, Z = CO2 gas compressibility at 96 °C and 1400 psi (Z = 0.746).
Berea sandstone
Berea sandstone is considered as an excellent sandstone for the laboratory experiments particularly in EOR processes. Berea sandstone is a sedimentary rock whose grains are predominantly sand-sized and are composed of quartz sand held together by silica. These core samples possess a chemical resistance to the erosive action of the acidic chemicals. Properties of these cores are presented in the Table 3.
Core flooding
The core flood apparatus from Sanchez Technologies, France, was used for foam/oil interaction in porous media experiments. The system consists of two automatic displacement injection pumps, back pressure regulator to maintain the pressure, a gas collector, a core holder which is assigned in an oven, three high-pressure accumulators and syringe pump for injecting CO2. Figure 1 presents a schematic diagram of core flooding experiment. Berea sandstone core was loaded in the core holder. The core holder was placed horizontally in all experiments. Distilled water was pumped in the annular space between the core holder to maintain the confining pressure. Three high-pressure accumulators were used to store and deliver crude oil, brine and surfactant blend solution. After that, these accumulators and core holder were placed in an oven at 96 °C and 1400 psi. Two automatic displacement pumps were used to displace crude oil, brine and surfactant blend solution through Berea sandstone core that was placed inside core holder. The back pressure regulator was used to maintain the pressure in the system. The back pressure during experiment was set 1400 psi which is equal to average pressure of operating reservoir. Recovered volumes of produced oil and water were measured by graduated cylinder.
Displacement steps
Water injection
To measure the absolute permeability of the Berea sandstone core sample, injection water was injected with injection rate of 0.2 cm3/min. Darcy equation was used to calculate the permeability.
Crude oil injection
The crude oil was injected at 0.2 cm3/min through the Berea sandstone core (brine saturated) until no more brine was produced. Irreducible water saturation (Swi) can be determined through oil drainage process. This simulates the first migration of crude oil to the reservoir rock where crude oil is gradually replacing the original wetting phase. At this step, oil permeability at irreducible water saturation can be determined. Original oil drainage process (OOIP) can be calculated by Eq. (3).
To establish the interaction between crude oil and Berea sandstone core, aging procedure was performed at same reservoir conditions.
Water flooding
Synthetic brine was injected at 0.2 cm3/min through the Berea sandstone core until 100% water cut. At this step, the residual oil saturation to water injection was measured. The residual oil saturation (Sor) can be calculated from Eq. (4).
Incremental oil recovery was calculated by using material balance equations including the oil left behind in the oil flooding and oil produce during different stages of flooding. The recovery factor (RF) at each step of oil production by injection of brine or gas can be calculated from Eq. (5).
SAG flooding
Two equal cycles of surfactant alternating gas were injected with injection rate of 0.2 cm3/min. The purpose is to check the performance of selected surfactant blend formulations for residual oil recovery after water flooding. Equal ratio 0.3PV of CO2 and 0.3PV of surfactant was injected in each cycle. The recovered volume of crude oil and brine in the graduated cylinder was noted. The oil recovery and residual oil saturation were calculated by volume of residual oil produced using material balance equations.
Results and discussion
Before core flooding experiment, interfacial tension (IFT) between injection water and crude oil was tested by spinning drop tensiometer. Selected surfactant formulations for core flooding experiment were reduced IFT between injection water and crude oil. The IFT between injection water, crude oil and surfactant solutions is presented in the Table 4. Core flooding experiments were performed to investigate the impact of three foam surfactant formulations on gas mobility and residual oil recovery. Berea sandstone core A, B and C were used for displacement tests. Table 5 presents fluid saturation inside a core during core flooding. After primary imbibition and establishing of residual oil saturation, the injection process is followed by CO2 flooding and surfactant alternating gas injection process. Table 6 presents the displacement steps performed on core flooding experiments. The pressure drop during the displacement is correlated with the recovery due to in situ generation and foam propagation.
Foam/crude oil interaction (core sample A)
After water flooding, CO2 (gas flooding) was injected with injection rate of 0.2 cm3/min. At the initial stage of gas injection, low volume of oil with water production was recovered. After continuous injection at the same flow rate, oil is produced at the exist point. The oil drop contains some gas bubbles, which can be attributed to the gas dissolution mechanism for residual oil recovery. At this point, gas breakthrough was not observed. The gas breakthrough can be detected by observing the bubbles of gas that appeared at the effluent recovery test tube. After gas breakthrough, the oil was recovered as the effluent like mixture of oil and gas. Figure 2 presents oil produced during gas flooding after gas breakthrough (mixture of oil and waxy components).
Surfactant blend of 0.6% AOS + 0.6% TX 100 solution followed by CO2 was injected with constant rate of 0.2 cm3/min. Two cycles of SAG1 and SAG2 with equal slug size of 0.3PV were injected. Differential pressures by SAG1 and SAG2 injected cycles were compared. Figure 3 presents the Δp profile of CO2 flooding and CO2 slug of SAG1 and SAG2 injection. CO2 injected in the first cycle of SAG1 showed increase in Δp which is inferred stable foam inside the core. The increase in Δp of CO2 slug is due to the injected slug of foam surfactant blend before injection of CO2 slug. The differential pressure curve starts to decrease after its maximum value. This maximum Δp corresponds to the foam breakthrough at the outlet. The decrease in Δp after breakthrough is because of the bubble coalescence due to diffusion or breaking of foam films (Yu et al. 2014). However, the decrease in Δp after foam breakthrough for this core sample A was very small. It indicates that the foam generated by this sample was stable and little foam coalescence occurred during the displacement process. Foam was not generated by CO2 slug in second cycle after second injected slug of surfactant solution due to high gas saturation. During gas displacement in the core, one possible reason is that, CO2 is not completely dispersed in to the surfactant solution to form a foam bank as a result the value of Δp remains low. Table 7 presents the amount of oil recovered and recovery factor (RF) based on original oil-in-place (OOIP).
The increase in volume of recovered residual oil is due to the formation of macroemulsion inside the core after the first slug of foam injected and foam breakage. Further, the microemulsion prevents the injected surfactant blend slug from generating the foam. Figure 4 presents the oil recovery by new surfactant blended formulation of 0.6% AOS + 0.6% TX-100. Maximum residual oil recovery resulted from new surfactant blend of 0.6% AOS + 0.6% TX-100 due to delay breakthrough time. Delay in breakthrough time increases the macroscopic efficiency and oil recovery consequently, as oil recovery in any displacement process depends on the volume of reservoir contacted by the injected fluid. The blend of this formulations increases the breakthrough time and improves the sweep efficiency due to the generated foam by CO2 in contact with surfactant solution. The generated foam increases the injected gas viscosity and increases the contact time of gas and crude oil.
Foam/crude oil interaction (core sample B)
The same displacement process was performed in core sample B. The gas mobility reduction was observed during slug of CO2 injection after foam surfactant solution. Figure 5 presents the differential pressure of CO2 before injection of surfactant and CO2 cycles of SAG1 and SAG2. The increase in Δp of CO2 slug after injected surfactant slugs showed strong interaction with crude oil. High-pressure differential values by injected CO2 slugs in both SAG1 and SAG2 cycles resulted in reduction in gas mobility due to generated foam inside the core. Therefore, sweep efficiency was improved by this surfactant blend formulation.
Figure 6 presents the oil recovery based on OOIP by surfactant blend of 0.6% AOS + 0.6% LMDO. Maximum volume of residual oil was recovered during fist injection of SAG1 cycle. The low oil recovery based on OOIP by this surfactant blend was noted as compared to surfactant blend of sample A. This may be due to its higher IFT values as compared to IFT values of sample A. Another possible reason for increase recovery of residual oil by SAG1 cycle is the contact of injected surfactant solution with CO2, which disperses the gas phase into the liquid phase. This results in the reduction in microscopic sweep efficiency due to gas bubbles in the liquid phase. Table 8 presents the total oil recovery by surfactant blend of 0.6% AOS + 0.6% LMDO.
Foam/crude oil interaction (core sample C)
To compare the result of blended surfactant formulations with single surfactant, one surfactant formulation was performed with same displacement steps. Two cycles of SAG1 and SAG2 with equal slug size of 0.3PV were injected. Differential pressure of SAG1- and SAG2-injected cycles was compared. Figure 7 presents the differential pressure of CO2 before injection of surfactant and CO2 cycles of SAG1 and SAG2. Injection of CO2 slug in the first cycle of SAG1 showed small increase in Δp which is inferred moderately stable foam inside the core. Increase in Δp of CO2 slug is due to the injected slug of surfactant. Increase in Δp of CO2 first slug showed gas mobility reduction in the core. Decrease in Δp of second CO2 slug showed that foam was not generated by injected slug of surfactant solution. This is because high gas saturation or injected CO2 slug is not completely dispersed into the surfactant solution to form a foam bank inside the core. Therefore, it resulted decrease in Δp.
Figure 8 presents the overall oil recovery by single surfactant 0.6% AOS. Table 9 presents the oil recovery based on OOIP (0.6% AOS). The low oil recovery based on OOIP by surfactant solution of 0.6% AOS is due to its single use in displacement process. This surfactant was not blended with nonionic or amphoteric surfactant.
Effects of new surfactant blend on oil recovery
Figure 9 presents the oil recovery with displacement steps by core sample A, B and C based on OOIP. Maximum oil recovery was by sample A (0.6 wt% AOS + 0.6 wt% TX-100). It was noted as 91.9% OOIP. Sample B (0.6 wt% AOS + 0.6 wt% LMDO) produced 83.7% OOIP. More oil recovery by core sample A is due to its strong interaction with crude oil and low IFT values as compared to core sample B. Core sample C (0.6 wt% AOS) produced 72.66% OOIP. This type of surfactant is not blended and used as a single surfactant. The oil recovery was improved by these surfactant formulations due to sulfonate group presence in the solution. The sulfonate group was stable at 96 °C, making these two surfactant blend formulation as strong candidates for EOR applications.
Conclusions
-
Three optimum surfactant formulations were evaluated in the presence of crude oil using Berea sandstone core samples at 96 °C and 1400 psi.
-
New surfactant blend formulations can be used and can perform better in the particular range of injection water (34107 ppm) and temperature 96 °C.
-
Surfactant blend formulations were reduced IFT values between crude oil and injection water.
-
Oil recovery based on original oil-in-place by new surfactant blend formulations of 0.6 wt% AOS + 0.6 wt% TX 100, 0.6 wt% AOS + 0.6 wt% LMDO and individual surfactant of 0.6 wt% AOS were recorded as 91.9, 83.7 and 72.66%, respectively.
-
Foam stability in presence of crude oil, reduction in gas mobility and increase in oil recovery indicated that these surfactant blends are good foaming agent as compared to individual surfactant in enhanced oil recovery (EOR) applications.
References
Al-Attar HH (2011) Evaluation of oil foam as a displacing phase to improve oil recovery: a laboratory study. J Petrol Sci Eng 79:101–112
Algharaib MK, Gharbi RB, Malallah A, Al-Ghanim W (2007) Parametric investigations of a modified swag injection technique, In: SPE Middle East oil and gas show and conference
Ashoori E, Marchesin D, Rossen W (2011) Roles of transient and local equilibrium foam behavior in porous media: traveling wave. Colloids Surf A 377:228–242
Bernard GG, Jacobs W (1965) Effect of foam on trapped gas saturation and on permeability of porous media to water. Soc Petrol Eng J 5:295–300
Blaker T, Aarra MG, Skauge A, Rasmussen L, Celius HK, Martinsen HA et al (2002) Foam for gas mobility control in the Snorre field: the FAWAG project. SPE Reserv Eval Eng 5:317–323
Blauer RE, Kohlhaas C (1974) Formation fracturing with foam. In: Fall meeting of the society of petroleum engineers of AIME
Boud DC, Holbrook OC (1958) US Patent No. 2,866,507. US Patent and Trademark Office, Washington, DC
Chang FF, Qu Q, Miller MJ (2002) Fluid system having controllable reversible viscosity, ed: Google Patents
Cubillos H, Montes J, Prieto C, Romero P (2012) Assessment of foam for GOR control to optimize miscible gas injection recovery. In: SPE improved oil recovery symposium
Deng Q-F, Liu L, Lin X-Z, Du G, Liu Y, Yuan Z-Y (2012) Synthesis and CO2 capture properties of mesoporous carbon nitride materials. Chem Eng J 203:63–70
Dholkawala ZF, Sarma H, Kam S (2007) Application of fractional flow theory to foams in porous media. J Petrol Sci Eng 57:152–165
Farzaneh SA, Sohrabi M (2013) A review of the status of foam application in enhanced oil recovery. In: EAGE annual conference and exhibition incorporating SPE Europec
Feng X, Mussone P, Gao S, Wang S, Wu S-Y, Masliyah JH et al (2009) Mechanistic study on demulsification of water-in-diluted bitumen emulsions by ethylcellulose. Langmuir 26:3050–3057
Hirasaki G (1989) A review of steam-foam process mechanisms. In: Paper SPE, vol 19518
Hirasaki G, Miller C, Szafranski R, Lawson J, Akiya N (1997) Surfactant/foam process for aquifer remediation. In: International symposium on oilfield chemistry
Karakashev SI, Grozdanova MV (2012) Foams and antifoams. Adv Colloid Interface Sci 176:1–17
Kovscek AR, Chen Q, Gerritsen M (2010) Modeling foam displacement with the local-equilibrium approximation: theory and experimental verification. SPE J 15:171–183
Lai C-C, Chen K-M (2008) Preparation and surface activity of polyoxyethylene-carboxylated modified gemini surfactants. Colloids Surf A 320:6–10
Mamun C, Rong J, Kam S, Liljestrand H, Rossen W (2002) Extending foam technology from improved oil recovery to environmental remediation. In: Paper SPE 77557 presented at the SPE annual technical conference exhibition, San Antonio, TX
Nadeson G, Anua NAB, Singhal A, Ibrahim RB (2004) Water-alternating-gas (WAG) pilot implementation, a first EOR development project in Dulang field, offshore Peninsular Malaysia, In: SPE Asia Pacific Oil and Gas Conference and Exhibition
R. LMNO Engineering, and Software, Ltd. Gas Viscosity Calculator [Online]. http://www.lmnoeng.com
Rogers JD, Grigg RB (2000) A literature analysis of the WAG injectivity abnormalities in the CO2 process. In: SPE/DOE improved oil recovery symposium
Sheng J (ed) (2013) Enhanced oil recovery field case studies. Gulf Professional Publishing
Svorstol I, Vassenden F, Mannhardt K (1996) Laboratory studies for design of a foam pilot in the Snorre field. In: SPE/DOE improved oil recovery symposium
Vikingstad AK, Aarra MG, Skauge A (2006) Effect of surfactant structure on foam–oil interactions: comparing fluorinated surfactant and alpha olefin sulfonate in static foam tests. Colloids Surf A 279:105–112
Wang D, Han P, Shao Z, Seright RS (2006) Sweep improvement options for the Daqing oil field. In: SPE/DOE symposium on improved oil recovery
Wang J, Yuan Y, Zhang L, Wang R (2009) The influence of viscosity on stability of foamy oil in the process of heavy oil solution gas drive. J Petrol Sci Eng 66:69–74
Wassmuth F, Green K, Hodgins L (2004) Water shutoff in gas wells: proper gel placement is the key to success. In: SPE/DOE symposium on improved oil recovery
Wheeler RS (2010) A study of high-quality foamed fracturing fluid properties. In: Canadian unconventional resources and international petroleum conference
Yu J, Khalil M, Liu N, Lee R (2014) Effect of particle hydrophobicity on CO2 foam generation and foam flow behavior in porous media. Fuel 126:104–108
Acknowledgements
We acknowledge the Universiti Teknologi PETRONAS for their support. The authors would like to thank Stepan Company, USA, who has supplied foam surfactants for this research study.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (http://creativecommons.org/licenses/by/4.0/), which permits unrestricted use, distribution, and reproduction in any medium, provided you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.
About this article
Cite this article
Memon, M.K., Elraies, K.A. & Al-Mossawy, M.I. Impact of new foam surfactant blend with water alternating gas injection on residual oil recovery. J Petrol Explor Prod Technol 7, 843–851 (2017). https://doi.org/10.1007/s13202-016-0303-1
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13202-016-0303-1