Abstract
The focus of this work is to highlight the relative response of Al-based micro- and nanocomposites in the form of enhancement in flexural strength via induced thermal stresses at high and cryogenic temperatures in ex situ and in situ atmospheres. In this investigation, we have tried to explore the reliability, matrix-reinforcement interaction and microstructural integrity of these materials in their service period by designing appropriate heat treatment regimes. Al-Al2O3 micro- and nanocomposites had been fabricated by powder processing method. The micro- and nanocomposites were subjected to down-thermal shock (from positive to negative temperature) and up-thermal shock (from negative to positive temperature) with varying thermal gradients. For isothermal conditioning, the composites were exposed to + 80 and − 80 °C for 1 h separately. High-temperature three-point flexural tests were performed at 100 and 250 °C on the composites. All the composites subjected to thermal shock and isothermal conditioning was tested in three-point flexural mode post-treatments. Al-1 vol.% Al2O3 nanocomposite’s flexural strength improved to 118 MPa post-thermal shock treatment of gradient of 160 °C. The Al-5 and 10 vol.% Al2O3 microcomposites possessed flexural strength of 200 and 99.8 MPa after thermal shock treatment of gradient of 160 and 80 °C, respectively. The observed improvement in flexural strength of micro- and nanocomposites post-thermal excursions were compared and have been discussed with the support of fractography. The microcomposites showed a higher positive scale of response to the thermal excursions as compared to that of the nanocomposites.
Similar content being viewed by others
References
S.C. Tjong and Z.Y. Ma, Microstructural and Mechanical Characteristics of In Situ Metal Matrix Composites, Mater. Sci. Eng., 2000, 29, p 49–113
J.S. Shelley, R. LeClaire, and J. Nichols, Project No: AFRL-PR-ED-TP-2001-023, Air Force Research Laboratory, Edwards AFB, Jan 2001
P. Mummery and B. Derby, The Influence of Microstructure on the Fracture Behaviour of Particulate Metal Matrix Composites, Mater. Sci. Eng. A, 1991, 135, p 221–224
A.A. Tofigh, M.R. Rahimipour, M.O. Shabani, and P. Davami, Application of the Combined Neuro-computing, Fuzzy Logic and Swarm Intelligence for Optimization of Compocast Nanocomposites, J. Compos. Mater., 2015, 49(13), p 1653–1663
A. Mazahery and M.O. Shabani, Investigation on Mechanical Properties of Nano-Al2O3-Reinforced Aluminum Matrix Composites, J. Compos. Mater., 2011, 45(924), p 1–8
M.O. Shabani, M.R. Rahimipour, A.A. Tofigh, and P. Davami, Refined Microstructure of Compo Cast Nanocomposites: The Performance of Combined Neuro-computing, Fuzzy Logic and Particle Swarm Techniques, Neural Comput. Appl., 2015, 26, p 899–909
M.O. Shabani and A. Mazahery, Searching for a Novel Optimization Strategy in Tensile and Fatigue Properties of Alumina Particulates Reinforced Aluminum Matrix Composite, Eng. Comput., 2014, 30, p 559–568
A. Mazahery and M.A. Shabani, A356 Reinforced with Nanoparticles: Numerical Analysis of Mechanical Properties, JOM, 2012, 64(2), p 323–329
N.C. Chapman, J. Silva, J.J. Williams, N. Chawla, and X. Xiao, Characterisation of Thermal Cycling Induced Cavitation in Particle Reinforced Metal Matrix Composites by Three-Dimensional (3D) X-Ray Synchrotron Tomography, Mater. Sci. Technol., 2015, 31(5), p 573–578
S. Chatterjee, S. Ghosh Sur, S. Bandyopadhyay, and A. Basumallick, Effect of Microstructure and Residual Stresses on Nano-tribological and Tensile Properties of Al2O3-and SiC-Reinforced 6061-Al Metal Matrix Composites, J. Compos. Mater., 2016, 50(19), p 2687–2698
H.R. Ezatpour, S.A. Sajjadi, M.H. Sabzevar, and Y. Huang, Investigation of Microstructure and Mechanical Properties of Al6061-Nanocomposite Fabricated by Stir Casting, Mater. Des., 2014, 55, p 921–928
K. Dash, S. Panda, and B.C. Ray, Effect of Thermal and Cryogenic Conditioning on Flexural Behavior of Thermally Shocked Cu-Al2O3 Micro- and Nano-composites, Metall. Mater. Trans. A, 2014, 45(3), p 1567–1578
K. Dash and B.C. Ray, A Study on Thermal Shock Response of Al-Al2O3 Micro-and Nanocomposites, 19th International Conference on Composite Materials, 28th July–2nd August, 2013, Montreal, Canada
K. Dash, Ph.D. Thesis, Processing and Characterization of Cu-Al 2 O 3 and Al-Al 2 O 3 Composites: An Emphasis on Micro- and Nano-particulate Reinforcements, 2014, National Institute of Technology, Rourkela, p 122–152
L.J. Broutman, Ed., Fracture of Metal Matrix Composites, Fracture and Fatigue, Volume 5: Composite Materials, Academic Press, New York and London, 1974, p 45–89
Acknowledgments
The authors would like to thank the National Institute of Technology (NIT), Rourkela for providing the necessary financial and infrastructural supports.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Dash, K., Ray, B.C. Response of Al-Based Micro- and Nanocomposites to Rapid Fluctuations in Thermal Environments. J. of Materi Eng and Perform 27, 3678–3687 (2018). https://doi.org/10.1007/s11665-018-3437-0
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11665-018-3437-0