Skip to main content
SpringerLink
Log in

Investigation on Nonmetallic Inclusions in Ultra-Low-Oxygen Special Steels

  • Published:
Metallurgical and Materials Transactions B Aims and scope Submit manuscript

Abstract

Investigation was carried out on inclusions in ultra-low-oxygen special steel by taking systematic samplings not only from secondary refining but also from continuous casting. It was found that RH degassing had a much stronger ability than LF refining in removing inclusions. Total oxygen (TO) can be further reduced from 0.0013 to 0.0015 mass pct to about 0.00047 mass pct without too much difficulty by elongating RH degassing time to 33 minute. Inclusions larger than 5 μm were decreased from 1.49 to 0.08 N/mm2 with a removal ratio of about 94 pct. During secondary refining, inclusions experienced continuous evolution from Al2O3 to the MgO-Al2O3, CaO-MgO-Al2O3, and CaO-Al2O3 system due to complex reactions among slag, steel, and refractory materials. Because of more efficient removal of solid inclusions, especially those large ones during RH treatment, thorough modification of solid inclusions into liquid CaO-MgO-Al2O3 can be achieved. Reoxidation during casting resulted in an obvious rise in Al2O3 content in inclusions, which offset the efforts made during secondary refining. Liquid CaO-Al2O3 systems after RH were changed to solid CaO-Al2O3, MgO-Al2O3, or CaO-MgO-Al2O3 again. Large inclusions with sizes approaching several hundred micron were frequently observed in casting bloom by a vast area of scanning under an automatic scanning electron microscope despite very low TO of about 0.00059 mass pct. A total of 78 pct of them were cluster-shaped CaO-MgO-Al2O3 solid inclusions with sizes as large as 200–330 μm. Most clusters over 100 μm were constituted by smaller particles with similar chemical compositions to other small singular inclusions in steel, which indicated that they were formed due to the aggregations of small inclusions during casting. Moreover, the location of them indicated a close relationship to the solidification microstructure of steel, which has not been covered before. It was impressively found that larger inclusions were mainly in the column grain zone area, while those in the central equiax grain zone of the bloom had smaller sizes.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12
Fig. 13
Fig. 14
Fig. 15
Fig. 16
Fig. 17
Fig. 18
Fig. 19

Similar content being viewed by others

References

  1. T. Uesugi: Tetsu-To-Hagane, 1988, vol. 74, p. 1889.

    Google Scholar 

  2. T. Uesugi: Trans. Iron Steel Inst. Jpn., 1986, vol. 26, p. 614.

    Article  Google Scholar 

  3. T. Uesugi: Trans. Iron Steel Inst. Jpn., 1988, vol. 28, p. 893.

    Article  Google Scholar 

  4. K. Tsubota and I. Fukumoto: Proc. 6th Int. Iron Steel Congress, Vol. 3, Steelmaking I, Nagoya, 1990, p. 637.

  5. K. Kawakami: The 3rd Int. Congress on the Sci. & Technol. of Steelmaking, Charlotte, 2005, p. 209.

  6. K. Kawakami: The 182–183th Nishiyama Technical Memorial Seminar, Tokyo-Osaka, 2004, p. 151.

  7. K. Kawakami: Sanyo Technical Rep., 2007, vol. 14, p. 22.

  8. K. Kawakami, T. Taniguchi, and K. Nakashima: Tetsu-To-Hagane, 2007, vol. 93, p.743.

    Article  Google Scholar 

  9. X. Yang: Bearings, 2012, no. 9, p. 54.

  10. X. Wang, W. Wang et al.: Asia Steel 2009 International Conference, Busan, 2009.

  11. M. Jiang, X. Wang, et al.: Steel Res. Int., 2010, vol. 81, p. 759.

    Article  Google Scholar 

  12. M. Jiang, X. Wang, et al.: ISIJ Int., 2010, vol. 50, p. 95.

    Article  Google Scholar 

  13. X. Wang, M. Jiang, et al.: Sci. China-Technol. Sci., 2012, vol. 55, p. 1863.

    Article  Google Scholar 

  14. Z. Deng, and M. Zhu: ISIJ Int., 2013, vol. 53, p. 450.

    Article  Google Scholar 

  15. P.R. Scheller and Q. Shu: VDEh-CSM Seminar, Düsseldorf, 2014.

  16. X. Wang, X. Li, et al.: Steel Res. Int., 2014, vol. 85, p. 155.

    Article  Google Scholar 

  17. Y. Miki, B.G. Thomas, et al.: Ironmaker Steelmaker, 1997, vol. 24, p. 31.

    Google Scholar 

  18. G. Yang, X. Wang, et al.: Steel Res. Int., 2014, vol. 85, p. 26.

    Article  Google Scholar 

  19. H. Todoroki and K. Mizuno: Iron Steelmaker Trans., 2003, vol. 61, p. 60.

    Google Scholar 

  20. J.H. Park: Mater. Sci. Eng. A, 2008, vol. 472, p. 43.

    Article  Google Scholar 

  21. N. Verma, M. Lind, P.C. Pistorius, and R.J. Fruehan: Iron Steel Technol., 2010, vol. 7, pp. 189–97.

    Google Scholar 

  22. S.F. Yang, Q.Q. Wang, L.F. Zhang, J, Lim, and K. Peaslee: Metall. Mater. Trans. B, 2012, vol. 43, p. 731.

    Article  Google Scholar 

  23. C.B. Shi, X.C. Chen, H.J. Guo, Z.J. Zhu, and X.L. Sun: Metall. Mater. Trans. B, 2012, vol. 44B, p. 378.

    Article  Google Scholar 

  24. H. Itoh, M. Hino, and S. Ban-Ya: Metall. Mater. Trans. B 1997, vol. 28B, p. 953.

    Article  Google Scholar 

  25. J.H. Park and H. Todoroki: ISIJ Int., 2010, vol. 50, p. 1333.

    Article  Google Scholar 

  26. G. Okuyama, K. Yamaguchi, et al.: ISIJ Int., 2000, vol. 40, p. 121.

    Article  Google Scholar 

  27. J.H. Park and D.S. Kim: Metall. Mater. Trans. B, 2005, vol. 36B, p. 495.

    Article  Google Scholar 

  28. J.H. Park, D.S. Kim, and S.B. Lee: Metall. Mater. Trans. B, 2005, vol. 36B, p. 67.

    Article  Google Scholar 

  29. K.C. Mills: Slag Atlas, 2nd ed., Verlag Stahleisen GmbH, Dusseldorf, Germany, 1995.

    Google Scholar 

  30. H.B. Yin, H. Shibata, T. Emi, and M. Suzuki: ISIJ Int., 1996, vol. 37, p. 936.

    Article  Google Scholar 

  31. H.B. Yin, H. Shibata, T. Emi, and M. Suzuki: ISIJ Int., 1996, vol. 37, p. 946.

    Article  Google Scholar 

Download references

Acknowledgments

Sincere appreciation is given to the Natural Science Fund of China (No. 51304013) and the National Basic Research Program of China (No. 2010CB630806) for the funding.

Author information

Authors and Affiliations

  1. School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing, People’s Republic of China

    Jin Zhu Li (Ph.D Candidates), Min Jiang ( Assistant Professor), Xiao-Fei He (Ph.D Candidates) & Xin-Hua Wang ( Assistant Professor)

  2. Technology Centre of Maanshan Iron and Steel Co. Ltd., Maanshan, An-hui Province, People’s Republic of China

    Wei Sun (Professorial Senior Engineer/Senior Director of Technology)

Authors
  1. Jin Zhu Li
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Min Jiang
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Xiao-Fei He
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Wei Sun
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Xin-Hua Wang
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Min Jiang.

Additional information

Manuscript submitted October 4, 2015.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Li, J.Z., Jiang, M., He, XF. et al. Investigation on Nonmetallic Inclusions in Ultra-Low-Oxygen Special Steels. Metall Mater Trans B 47, 2386–2399 (2016). https://doi.org/10.1007/s11663-016-0687-9

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11663-016-0687-9

Keywords

Search

Navigation