Abstract
The feasibility of processing duplex stainless steels with promising properties using a powder metallurgical route, including the consolidation by field-assisted hot pressing, is assessed in this investigation. The influence of the particle size and morphology of the raw austenitic and ferritic powders on the final microstructure and properties is also evaluated for an austenitic content of 60 wt pct. In addition, the properties of a new microconstituent generated between the initial constituents are analyzed. The maximum sintered density (98.9 pct) and the best mechanical behavior, in terms of elastic modulus, nanohardness, yield strength, ultimate tensile strength, and ductility, are reached by the duplex stainless steel processed with austenitic and ferritic gas atomized stainless steel powders.
Similar content being viewed by others
References
L.A. Dobrzanski, Z. Brytan, M. Actis Grande and M. Rosso: Arch. Mater. Sci. Eng. A, 2007, vol. 28, pp. 217-23.
J. Charles: Proc. Conf. Duplex Stainl. Steels 91, Beaune, France, 1991, vol. I, pp. 3–48.
J. M. Ruiz-Prieto, W. Moriera, J. M. Torralba and L. E. G. Cambronero: Powder Metall., 1994, vol. 37, pp. 57-60.
T. Marcu Puscas, A. Molinari, J. Kazior, T. Pieczonka and M. Nykiel: Powder Metall., 2001, vol. 44, pp. 48-52.
V. Muthupandi, P. Bala Srinivasan, S.K. Seshadri and S. Sundaresan: Mater. Sci. Eng. A, 2003, Vol. 358A, pp. 9-16.
R. Magnabosco: Mater. Res., 2009, vol. 12, pp. 321-27.
M. Cazzolli: Ph.D Thesis, University of Trento, 2015.
P. Datta and G.S. Upadhyaya: Mater. Chem. Phys., 2001, vol. 67, pp. 234-42.
M. Campos, J.J. Muñoz, A. Bautista, F. Velasco and J.M. Torralba: Mater. Sci. Forum, 2003, vol.426-32, pp. 4343-48.
J. Kazior, M. Nykiel, T. Pieczonka, T. Puscas and A. Molinari: J. Mater. Process. Technol., 2004, vol. 157-158, pp. 712-17.
J.M. Torralba, A. Monsoriu, J.M. Ruiz-Román, J.R. Ibars and F. Velasco: J. Mater. Process. Tech., 1995, vol. 53, pp. 433-40.
M. Campos, A. Bautista, D. Cáceres, J. Abenojar and J.M. Torralba: J. Eur. Ceram. Soc., 2003, vol. 23, pp. 2813-19.
C. García, F. Martín, Y. Blanco, M.P. de Tiedra and M.L. Aparicio: Corros. Sci., 2009, vol. 51, pp. 76-86.
C. García, F. Martín, Y. Blanco and M.L. Aparicio: Corros. Sci., 2010, vol. 52, pp. 3725-37.
Dobrzański LA, Brytan Z, Grande MA, Rosso M, J. Mater. Process. Tech., 2007, vol. 192, pp. 443-48.
W.A. Kaysser and W. Weise: Ullmann’s Encyclopedia of Industrial Chemistry, Wiley, Weinheim, 2012, pp. 1-39
M.A. Bousnina, A. dakhlaoui Omrani, F. Schoenstein, P. Madec, H. Haddadi, L.S. Smiri and N. Jouini: J. Alloys Compd., 2010, Vol. 504, pp. S323-27.
A. García-Junceda, L. Acebo and J.M. Torralba: Metall. Mater. Trans. A, 2015, Vol. 46A, pp. 3192-98.
Andrej Salak: Ferrous powder metallurgy, Cambridge International Science Pub, Cambridge, 1995.
F. Martín, C. García, Y. Blanco and M.L. Rodríguez-Méndez: Mater. Sci. Eng. A, 2015, vol. 642A, pp. 360-65.
J. R. Davis 1998, Metals Handbook, 2nd ed., ASM International, Materials Park, Ohio
O Smuk, H. Hänninen and L. Liimatainen: Mater. Sci. Tech., 2004, vol. 20, pp. 641-44.
Acknowledgments
This research did not receive any specific grant from funding agencies in the public, commercial, or not-for-profit sectors.
Author information
Authors and Affiliations
Corresponding author
Additional information
Manuscript submitted April 24, 2017.
Rights and permissions
About this article
Cite this article
García-Junceda, A., Rincón, M. & Torralba, J.M. Development of Duplex Stainless Steels by Field-Assisted Hot Pressing: Influence of the Particle Size and Morphology of the Powders on the Final Mechanical Properties. Metall Mater Trans A 49, 264–271 (2018). https://doi.org/10.1007/s11661-017-4385-2
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11661-017-4385-2