Abstract
Purpose
Germanium (Ge) is known as a Technology Critical Element (TCE) and has been widely used in electronic and industrial products. Waste electronic and electrical equipment (WEEE) containing germanium goes to WEEE treatment plants. The transfer of Ge in the environment makes it necessary to get to know its mobility, reactivity, and chemical transformations in soil. The objective of this research was to develop a methodology for germanium speciation in soil under pressure from storage, processing, and recovery from electrowaste.
Materials and methods
Thirty soil cores (30 cm long) were collected from an area around a WEEE plant, using a Humax soil sampler. Soil magnetometry methods were used for the first time during the determination of soil sampling points for germanium. After basic physicochemical analysis (pH, Eh, total element concentration using the ICP-MS technique), soil samples were prepared for germanium speciation. The optimisation and validation of a methodology for determining Ge species in easily-leached fractions of soil collected from areas around an electrowaste plant, was studied using Ion Chromatography-Inductively Coupled Plasma-Mass Spectrometry (IC-ICP-MS). Chromatographic conditions were optimised, taking soil matrix effects into account. Optimised Ge extraction from the soil included: extraction time, type of extractants, extraction support using shaking, and ultrasound.
Results and discussion
The Ge species (Ge(IV), monomethylgermanium (MMGe), and dimethylgermanium (DMGe)) were successfully separated after 12 min on a Dionex IonPac AS9-HC column with ammonium nitrate and potassium sodium tartrate as an elution phase. The highest extraction efficiency was achieved by using 100 mM NH4NO3 with 1 mM potassium sodium tartrate as an extractant, that washes out Ge from soils within 4 h. In most cases, the soils contained a Ge(IV) form. Germanium methyl derivatives were only found in a few soil samples. Our research showed that germanium concentration in the studied area was as high as 7.64 mg.kg−1, with an average concentration of 3.51 mg.kg−1. The results allowed the creation of a correlation matrix, which identified many strong correlations.
Conclusion
This research confirmed the impact of a WEEE plant on the increase of the Ge content in topsoil, when in direct proximity. Increased germanium content occurred in soil samples located north of the emitter, which is consistent with the prevailing wind direction. The study confirmed that the soil magnetometry method is applicable for detecting TCE. Soil samples with the highest content of germanium had a very high magnetic susceptibility and there is a correlation between these parameters.
Similar content being viewed by others
Explore related subjects
Discover the latest articles, news and stories from top researchers in related subjects.Avoid common mistakes on your manuscript.
1 Introduction
Germanium is recognised as a critical and rare element (Yellishetty et al. 2017), while its properties are exploited in electronics and renewable energy applications on an increasingly large scale. An increase in Ge use has been observed in new technologies. For this reason, the risk of its uncontrolled release into the soil is growing through the disposal of waste electrical and electronic equipment (WEEE) (Işıldar et al. 2018; Julander et al. 2014). Industrial interest in this element raises the need to assess its potential environmental impact (Perkins et al. 2014). Germanium is one of the Technology Critical Elements (TCE) (Jabłońska-Czapla and Grygoyć 2022; Jabłońska-Czapla et al. 2022; Wojcieszek et al. 2017) and has been widely used in electronic and industrial products like semiconductor detectors, the optical and telecommunication industries, wind turbines, electric vehicles, photovoltaics, and energy-efficient lighting (Nuss and Blengini 2018). The increasing use of modern technologies leads to the release of more and more quantities of TCE into the natural environment. For this reason, the scientific community is increasingly interested in the natural processes associated with TCEs, as well as their impact on living organisms and their potential threat to human health (Cobelo-García et al. 2015). Germanium dioxide intake is known to cause serious side effects, including organ dysfunction and even death. The global mean concentration of Ge in topsoil is estimated at 2 mg.kg−1 and varies in the range < 0.1–15.0 mg.kg−1, when considering the variety of soils forming under strongly different pedogenic conditions (Wiche et al. 2018). The global concentration of germanium in soil depends on geogenic and anthropogenic factors. For example, a study of the mining area of Freiberg (Germany) showed that the total concentration of Ge in soil varied considerably, ranging from 1.0–4.3 mg.kg−1 (mean 1.9 mg.kg−1) (Wiche et al. 2017).
The main analytical techniques for determining the total germanium content in soils are atomic spectrometric techniques, such as Inductively Coupled Plasma Optical Emission Spectroscopy ICP-OES (Rosenberg 2007), Inductively Coupled Plasma Mass Spectrometry ICP-MS (Delvigne et al. 2017; Okoroafor et al. 2022), Atomic Absorption Spectroscopy AAS (Hambrick et al. 1984), High Resolution Inductively Coupled Plasma Mass Spectrometry HR-ICP-MS (Delvigne et al. 2009), Laser Ablation Inductively Coupled Plasma Mass Spectrometry LA-ICP-MS (Belissont et al. 2014), and spectrophotometry (Soylak and Yigit 2015).
The metal and metalloid species in which they occur have a significant impact on their mobility, reactivity, transformation, and toxicity (Templeton and Fujishiro 2017). Therefore, speciation analysis is very important to understanding its natural behaviour in nature or determining the toxicity and ecotoxicity (Krystek and Ritsema 2004; Tricas et al. 2014). Germanium occurs as Ge(II), Ge(IV), Monomethylgermanium (MMGe), dimethylgermanium (DMGe), and Trimethylgermanium (TMGe). Germanium methyl derivatives are produced by methylation, assisted by microorganisms (Rosenberg 2009; Thayer 2002). In seawater, methylated forms of germanium account for 70% of dissolved germanium (Romero-Freire et al. 2019). However, there is insufficient information in the literature on the content of methyl derivatives of this element in soils. It was found that Ge(IV) displays nutrient-like behaviour in estuaries and surface waters, similar to silicon (Padro et al. 1995). Hyphenated techniques are useful for analysing different germanium forms (Lehmann et al. 2019; Padro et al. 1995). Ge species may be separated by liquid chromatography, often with the addition of chelating agents for complexation (Smichowski and Marrero 1998). In ICP-MS techniques, the application of a dynamic reaction cell (DRC) allows for the elimination of mass spectral interference (Zhang et al. 2017). Little is known about the geochemical behaviour and speciation of Ge in soils (Wiche et al. 2018). Ge speciation in soil solutions and its mobility in soils may strongly depend on the pH. Acidic soil conditions and a high proportion of germanium in the organic fraction may affect the availability of this element to plants (Wiche and Heilmeier 2016).
The content of germanium in soils, around the areas associated with the processing of electronic waste has not yet been widely studied. The only studies on trace metal content from e-waste (electrowaste)-contaminated soils were carried out by Cui et al. (2017). However, they only tested the content of metals such as Cd, Pb, Zn, Cr, Ni, and Cu. Our earlier study (Jabłońska-Czapla et al. 2021) showed that the highest concentration of germanium was found in the topsoil, and it was over 8 mg.kg−1. The mean concentration of germanium in the upper soil layer was 4.8 mg.kg−1. The concentration of this element fell as the soil profile increased in thickness, with few exceptions; the lowest concentration of germanium occurred in the soil samples with a thickness of 15–18 cm of the soil profile. Therefore, one of the objectives of the research was to identify which species of germanium occur in areas near to WEEE processing plants. The second aim was the optimisation and validation of a methodology for determining the matrix effects and extracting the inorganic Ge(IV) and methylated derivatives (monomethylgermanium (MMGe) and dimethylgermanium (DMGe)) from easily-leached soil fractions using Ion Chromatography-Inductively Coupled Plasma-Mass Spectrometry (IC-ICP-MS).
2 Materials and methods
2.1 Sampling area and sample preparation
Samples were collected around the WEEE (Waste Electrical and Electronic Equipment) plant located in the Metropolis of Upper Silesia and Zagłębie in Poland (Fig. 1). This area is the most industrialised and heavily urbanised area of Poland, where numerous enterprises related to the mining and metallurgical industries are located. The company itself is located in the southern, densely forested district of Katowice City and collects used devices and components from electrical and electronic devices. The company is also interested in any waste containing precious metals such as gold, silver, palladium, platinum, rhodium, and iridium. The germanium content in the waste stored and processed in the plant was confirmed in our previous studies (Fornalczyk et al. 2019; Willner et al. 2021). Wastes are segregated and collected according to type, and stored in containers and large bags on a hard surface. The storage site is covered, which protects the waste from contact with rainfall and prevents the leakage of metal compounds and hazardous substances directly into the soil. In one of the closed halls, the manual disassembly of electronic elements and components is carried out. In another closed hall, the process of ‘skinning’ copper cables is performed with the use of a cable recycling machine. In addition, soil samples were collected in an agricultural area near Lublin (Poland), which was not subjected to industrial anthropopressure, and treated as background readings.
In the beginning, the low-field volume magnetic susceptibility (κ) was measured in situ using an MS2 Bartington meter, equipped with an MS2D loop sensor. Sixty points of surface magnetic susceptibility measurements were performed on the study area. At each point, the κ value (expressed in 10–5 SI units) was calculated as the mean value of 11 readings within 2m2. The localisation of individual sampling points was confirmed using a Garmin GPS navigation device. Soil samples were collected in a similar way to previous studies (Rachwał et al. 2015, 2017a, b). From 30 selected sampling points, two 30 cm long soil cores were collected using a Humax soil sampler. Immediately after sampling, the soil cores were placed in tubes to limit contact with atmospheric air and ore impurities. On the same day that the samples were taken, they were delivered to the institute's laboratory. After transporting soil cores to the laboratory, to determine the vertical distribution of magnetic susceptibility and (indirectly) the depth of migration of pollutants along the soil cores, the magnetic susceptibility was measured using a Bartington MS2C meter with a resolution of 1 cm. From the depths characterised by the highest values of magnetic susceptibility (generally 3–6 cm), the soil samples were separated and subjected to chemical analysis after air drying, averaging, and sieving through a sieve with a diameter of 2 mm. Air dried samples were stored in polypropylene (PP) containers and analysed within one month.
The basic physicochemical parameters of soils, such as pH and Eh (redox potential), were determined the day after the samples were delivered to the laboratory. Redox potential was measured using an ERPt-111 electrode (Elmetron, Zabrze, Poland) and pH was measured using an ERH-111 electrode (Elmetron, Poland).
2.2 Reagents and standards
Standard solutions for total germanium determination were prepared from a 1000 mg.L−1 germanium standard for ICP and 100 mg.L−1 metalloid non-metal mix for ICP, both from Sigma-Aldrich (Switzerland). The certified ICP-MS quality control standard no.1, ICP-MS calibration standard no. 2, and ICP-MS Multi-element standard solution VI (AccuStandard, USA) were used for other elements in the total analysis of the matrix. All working solutions were prepared with acidified (suprapur 65% nitric acid, Merck, Darmstadt, Germany), deionized water obtained from an ultrapure Hydrolab water purification system (HLP 10 UV, Poland). An internal standard 10 µg.L−1 rhodium (Merck, Darmstadt, Germany) solution was used. Standard stock solutions for the HPLC speciation of germanium species (DMGe, MMGe and Ge(IV)) were prepared from dimethyldichlorogermane (CH2Cl2Ge,99%, Acros Organics, UK), methyltrichlorogermane (CH3Cl3Ge, 97%, Gelest, USA) and germanium(IV) oxide (GeO2, 99.9%, Aldrich Chemistry, USA). The mobile phase was prepared by dissolving an appropriate amount of ammonium nitrate (≥ 99.0%, Sigma-Aldrich, USA) and potassium sodium tartrate tetrahydrate (99%, Sigma-Aldrich, USA). In addition, diluted phosphoric acid (85%, Merck) was used to improve elution strength.
2.3 Determination of the total content of germanium
The soil core samples were transported to the laboratory and preliminary operations were performed, consisting of air-drying, manual grinding in a porcelain mortar and sieving through a sieve with a 2 mm diameter mesh. This procedure allowed for separation into so-called earthy and skeletal parts. The last step was to grind samples in an electric mortar and sieving to a < 0.2 mm grain diameter.
Soil samples were digested in acidic conditions (2 ml HNO3, 6 ml HCl and 3 ml HF) in an Anton Paar 3000 (Austria) microwave oven. A 0.2 g air-dried soil sample was transferred to a vessel and digested at 1400 W power for 30 min. After digestion, the solution was poured into a polypropylene volumetric flask and diluted to 50 ml. The 73324 Certified Reference Material of soil (China National Analysis Center for Tron and Steel, Beijing, China) was used for quality control in the analysis of total germanium.
To carry out soil sampling with maximal signal intensity and minimal interference effects during the analysis, the instrument parameters, such as quartz torch position, voltages of ionic lenses, radio frequency detector power, nebuliser gas flow, and DRC reaction gas flow, were optimised. The final working conditions are listed in Table 1.
The total content of Ge and other elements in the matrix were determined using an Elan 6100 DRC-e ICP-MS spectrometer (PerkinElmer, USA). Samples and standards were delivered with a peristaltic pump. The spectrometer was optimised daily, with a 10-µg.L−1 solution (Mg, Cu, Rh, Cd, In, Ba, Ce, Pb, and U) in 1% HNO3 Elan 6100 Setup/Stab./Masscal. Solution (PerkinElmer). The concentrations of metals were measured with the internal 103Rh standard.
Germanium determination using ICP-MS spectroscopy is difficult because of numerous spectral interferences: 70Ge (35Cl17O18O+, 36Ar34S+, 38Ar32S+, 70Zn+), 72Ge (36Ar2+, 56Fe16O+,40Ar32S+, 40Ar16O2+, 55Mn16OH+), and 74Ge (40Ar34S+, 36Ar38Ar+, 40Ar36S+, 37Cl2+,74Se+) (Filella and Rodushkin 2018; Zhang et al. 2017). In order to eliminate these polyatomic interferences, DRC technology (with CH4 as the reaction gas) was used. The flow rate of the reaction gas and the value of the rejection parameter (Rpq) were the key parameters of the DRC operation. The optimised CH4 flow rate was selected at 0.4 mL min−1 and when the Rpq value was 0.65, the signal of 74Ge tended to be stable. Under the optimised conditions, the analytical performance of the proposed method was evaluated. Standard solutions with Ge concentrations from 1 to 25 µg L−1 were analysed to construct a calibration curve with a correlation coefficient of 0.9998.
2.4 Method development of germanium speciation
Three germanium species were simultaneously separated and determined by HPLC, combined with an ICP-MS spectrometer. The technical characteristics of the equipment were: a high-performance liquid chromatograph Series 200 (Perkin Elmer) system including a Peltier column oven, autosampler, gradient pump, vacuum degasser, and control unit. An anion exchange IonPac AS9-HC (Dionex) column (250 mm × 4 mm, 9 μm) was chosen to successfully separate the Ge(OH)4, DMGe, and MMGe forms. The samples and standard solutions were injected via a 200 µl sample loop on a column. HPLC kit was hyphenated with an ICP-MS DRC-e Elan 6100 (Perkin Elmer) spectrometer as an elemental detector via a valve and Scotch-type spray chamber. The determination of Ge was conducted using the ICP-MS technique in DRC-e mode, to remove polyatomic plasma- and matrix-based interferences. The optimised working conditions of the ICP-MS instrument are presented in Table 1.
Samples were extracted for soil speciation analysis. Liquid extraction is not as efficient as microwave digestion; however, high temperatures and reagents may change the degree of oxidation of element species. The method of soil extraction was optimised to extract as much germanium as possible. 10 ml of 100 mM potassium sodium tartrate was added to 2 g of the sample. Extraction was carried out using an ultrasonic cleaner (Sonic 5, Polsonic, Warszawa, Poland), and then the samples were centrifuged by a Beckman Coulter Avanti JXN-26 centrifuge (20,000 rpm, JA-25.50 Fixed-Angle Aluminium Rotor type).
The optimisation of germanium extraction from soils was conducted using various solutions: 20 mM Na2EDTA; 100 mM citric acid with 20 mM Na2EDTA pH 3.8; 100 mM citric acid; 300 mM ammonium tartrate; 100 mM NH4NO3 with 1 mM potassium sodium tartrate; and 100 mM potassium sodium tartrate. Extraction efficiency, using the optimised method, was calculated as the ratio of germanium species determined by HPLC-ICP-MS to total germanium determined by ICP-MS, after microwave digestion.
The solution was then subjected to HPLC-ICP-MS analysis. Germanium compounds were separated by employing a gradient of a mixture of 7 mM NH4NO3, 1 mM potassium sodium tartrate tetrahydrate (pH 5) (adjusted by adding HNO3), 100 mM NH4NO3, 1 mM potassium sodium tartrate, and 20 mM H3PO4 (pH 2.1). Potassium sodium tartrate had to be added to each sample, up to a final concentration of 80 mM to each sample and standard solution, to avoid co-elution of germanium forms. The total time for separating germanium forms was 12 min. The optimised separation parameters for the simultaneous determination of DMGe, MMGe, and inorganic Ge(IV) species are presented in Table 2.
2.5 Method validation of germanium speciation
The calibration curve was obtained by measuring the calibration standard solutions of germanium species five times. A 1 g.L−1 stock standard solution of DMGe, MMGe, and Ge(OH)4 were mixed before analysis, to reach final concentrations of 0.5, 1.0, 2.5, 5.0, 7.5, and 10.0 µg.L−1 of each form, subjected to the extraction procedure and analysed by the HPLC-ICP-MS system. The average intensity value for each standard was taken to construct the calibration curve. Example chromatograms, obtained during the calibration of the IC-ICP-MS system, are shown in Fig. 2a.
a Superimposed chromatograms obtained after analysing standard solutions of MMGe, DMGe, and Ge(IV) with concentrations of 0.5, 1,0, 2.5, 5.0, 7.5, and 10.0 μg.L−1, respectively; b chromatogram of the real soil sample No. 5 taken from the area surrounding the WEEE processing plant; c chromatogram of the real soil sample No. 4 taken from the area surrounding the WEEE processing plant
An 80 mM potassium tartrate solution was used to prepare all blanks, standards, and sample dilutions. The respective correlation coefficients obtained were: 0.9996, 0.9999, and 0.9997 for DMGe, MMGe and Ge(IV). A linear model of the dependence of the concentration of the total number of analyte counts was selected. The chosen operating ranges for calibration curves were statistically verified by checking the distribution of variances using Snedecor’s F test. The limit of detection (LOD) and quantification was calculated from mixed standard solution calibration curves and was based on the following dependencies (1):
where LOD is the limit of detection; SD is a standard deviation value; and b is the slope of the calibration curve. The limit of quantification was set as three times the LOD.
The standard deviation values were determined as the standard deviation of 10 replicates of mixed standard solutions at concentrations of 0.5, 5.0, and 10.0 µg.L−1 and subjected to the extraction procedure for DMGe, MMGe, and Ge(IV), respectively. Repeatability was evaluated for germanium forms in real samples after five replicate analyses. The recovery was determined with measurements of the real samples spiked with a known amount of mixed standard solution containing all investigated species. The selected method validation parameters are presented in Table 3.
Matrix effect (ME) refers to the matrix, which often significantly interferes with the analyte analysis process. It is an important parameter that affects the selectivity and sensitivity of the quantitative analysis and is calculated using Eq. (2):
where ME(%) is the matrix effect; k1 is the slope of the matrix standard curve; and k2 is the slope of the solvent standard.
When the value of ME(%) is > 50%, there is a strong matrix effect. If the value is between 20–50%, there is a medium matrix effect. No matrix effect is considered when ME is in the range 0–20%. Positive and negative values mean signal enhancement or suppression induced by the matrix, respectively (Yang et al. 2021).
To determine Ge species accurately, matrix effects were evaluated by performing standard addition calibrations and external calibrations (D’Amore et al. 2023). The MEs calculated using Eq. (2) were between −20% and 20%, indicating that there was no matrix effect. In addition, the values of spike recovery were tested by F-tests. At a confidence level of 95%, no significant differences were found.
3 Results and discussion
3.1 Optimisation of the chromatographic separation
Our research included the chemical speciation of germanium, directly determined by chromatographic separation (HPLC) followed by elemental detection ICP-MS. In this study, we developed the method described in Lehmann et al. (2019). However, some modifications were necessary. This was because the above-mentioned authors conducted their research using an instrument with much better analytical performance, equipped with a triple quadrupole. In this work, we used an instrument with a single quadrupole and a different collision/reaction cell gas. Therefore, it was necessary to make some improvements to the method, to be able to carry out the study. Optimisation of the mobile phase composition was conducted to achieve the best possible separation of DMGe, MMGe, and inorganic Ge signal. The method was optimised by different conditions, such as injection volume, the concentration of tartrate in the sample and gradient pump flow. To improve the separation, different amounts of potassium sodium tartrate were added to the standards and the effect was checked. With an 80 mM concentration of tartrate, separation was not fully successful because DMGe and MMGe forms were not separated. Increasing the tartrate concentration to 100 mM resulted in good resolution and sharp peak shapes. The addition of potassium sodium tartrate to samples and standards is necessary to avoid the co-elution of three Ge species. Germanium species forms were separated by employing a gradient of a mixture of: 7 mM NH4NO3, 1 mM potassium sodium tartrate, pH 5.0, and 100 mM NH4NO3, 1 mM potassium sodium tartrate, 20 mM H3PO4, pH 2.1. The flow rate was set at 1 ml.min−1. All of the optimised parameters used in the method are presented in Table 2. The validation parameters for the simultaneous determination of germanium species are presented in Table 3.
3.1.1 Influence of the injection volume, flow rate, and concentration of tartrate in the samples
The relation between injection volume and peak height is linear. The appropriate injection volume of the sample in HPLC improves signal intensity and influences retention times. The effect of the injection volume was checked over the range 40–150 µl. A volume of 40 µl was insufficient to achieve a good retention process. In contrast, injection with a volume of 150 µl resulted in peak broadening and the overlapping of signals. Problems with peak shape may be caused by mass overload, when the excess liquid sample is injected into the column. Therefore, an optimal value of injection volume of 100 µl was selected.
As an addition to the sample, the potassium sodium tartrate concentration was checked in the range of 80–120 mM. Based on Lehmann's research (Lehmann et al. 2019), a tartrate concentration of 80 mM was initially tested. However, under these conditions, the separation of analytes was not completely reached and the peaks of the organic forms of germanium were not fully divided. Increasing the concentration of this salt to 100 mM results in a slightly longer retention time of MMGe and makes the peak sharper and better separated from the DMGe signal. A 120 mM concentration of tartrate accompanied the flattening and spreading of the MMGe peak and worsened the separation. Therefore, a 100 mM tartrate concentration solution was used in further experiments. Figure 3 presents the chromatograms obtained when using different concentrations of potassium sodium tartrate.
The effect of the flow rate was tested at three levels: 0.4, 0.8 and 1.0 ml.min−1. Reduction in the retention times for DMGe and MMGe analytes was observed with the increase of the mobile phase flow rate (Fig. 3). The flow rate of the mobile phase was set at 0.8 ml·min−1 during chromatographic separation. The total time for separating germanium species was 12 min. All of the optimised parameters used by this method are presented in Table 2.
3.2 Optimisation of soil sample extraction
The soils intended for germanium speciation analyses were extracted for 1, 2, 3 and 4 h. Extraction was initially assisted by shaking; however, the extraction efficiency was lower and so ultrasonic-assisted soil extraction was performed. The effect of extraction time on the degree of germanium leaching was investigated after 1, 2, 3, and 4 h. Figure 4 shows the results of germanium extraction from soils using various solutions (20 mM Na2EDTA; 100 mM citric acid with 20 mM Na2EDTA pH 3.8; 100 mM citric acid; 300 mM ammonium tartrate; 100 mM NH4NO3 with 1 mM potassium sodium tartrate; and 100 mM potassium sodium tartrate). This research has shown that the best extraction efficiency was obtained using 100 mM NH4NO3 with 1 mM potassium sodium tartrate acting as an extractant, washing out germanium from soils within 4 h.
3.3 Application of the developed Ge speciation method
The developed germanium extraction methods allowed for the analysis of soil samples taken from areas subjected to anthropopressure from the WEEE plant in Katowice. The total content of metals and metalloids, including germanium and its species, are shown in Table S1. Figure 5 graphically shows the germanium concentration in the area surrounding the WEEE plant. The map of total Ge content was prepared using Surfer 8 software, based on 30 irregularly spaced soil sampling points. The map was created using gridding method which was point kriging with the default linear variogram. The regularly spaced, rectangular arrays of grid nodes, with a calculated Z value at each node, from irregularly spaced XYZ data were produced. Gridding calculated the Z values for grid nodes where data exists, as well as for grid nodes in the holes where no data exists, by the mathematical algorithms. However, Table 4 presents the results of soil sample speciation analysis after NH4NO3 with potassium sodium tartrate extraction. The results of the speciation analysis showed that, in the soils around the electrowaste processing plant, germanium was mainly present in Ge(VI) form. Methyl germanium derivatives were only found in a few soil samples. In five soil samples, apart from Ge(IV), there was a monomethyl derivative of germanium and, in one sample, a dimethyl derivative of this element was found. It is difficult to relate the results obtained by this research to the content of methyl germanium forms in soils, due to the lack of available references. From the available information, it is known that methyl germanium derivatives are found in seawater. The presence of MMGe and DMGe in the soil is possible due to the biomethylation processes triggered by bacteria (Rosenberg 2009; Thayer 2002).
The highest concentration of germanium was almost 7.3 mg.kg−1. As shown in Fig. 5, an increased concentration of germanium occurred in soil samples located north of the electrowaste processing and sorting plant, which is consistent with the prevailing wind direction in this area (north, north-east). Figure 2b and c show the chromatograms of the soil samples numbered 5 and 4, taken from the area surrounding the WEEE processing plant.
In sample No. 5, two forms of germanium were found, in the form of MMGe and inorganic germanium (iGe) but, in sample No. 4, DMGe and inorganic germanium species were found.
Most of the articles focussing on the study of methyl germanium derivatives focus on water samples. It is well-known that MMGe and DMGe are more abundant than iGe in seawater. The number of methyl species of germanium presents conservative ratios between them (García-Figueroa et al. 2021). The available research on methylgermanium derivatives in soil is particularly scarce and knowledge about its behaviour in a soil environment is even less. In our study, monomethyl derivatives were found in seven samples, while dimethyl derivatives were only found in one sample. It seems that the coexistence of methyl derivatives is less pronounced in soil than in water samples, and these forms may behave differently. The results of our work are consistent with those of Hirner et al. (2000), for contaminated soil. Both DMGe and MMGe were present in one soil sample, while only one of the forms was present in the other two samples. The occurrence of organometallic species in the environment is due to natural processes under specific criteria. However, anthropogenic activities also lead to local conditions enabling methanogenesis and biomethylation. It is worth mentioning that the content and emission potential of hazardous waste, such as industrial waste or electronic waste, have rarely been examined for organometallic compounds. It transpires that methyl germanium derivatives were found in soil samples taken from the area to the north of the WEEE plant, which has the highest concentration of germanium in the study area. Figure 5 presents the spatial distribution of the total germanium contents of samples 5, 6, 9, 15, and 26, which are characterised by the highest concentrations of this element.
3.4 Results of element concentration and correlations between the germanium and other test parameters
Table S1 shows the total concentration of the elements in the soil samples. The germanium concentration ranges from 1.04–7.56 mg.kg−1. The analysed soil samples contain significant amounts of heavy metals: up to 1369 mg.kg−1 of lead and 593.3 mg.kg−1 of zinc.
The concentration of TCE is correlated with base metals (Filella and Rodríguez-Murillo 2017). The soil magnetometry method has been successfully used in soil contamination studies, due to the correlation found between magnetic susceptibility and the content (often excessive) of metals and metalloids in soils (Rachwał et al. 2017a, b). Therefore, the use of magnetic susceptibility measurements to determine the locations of likely accumulations of TCE seems to be justified. The increased concentration of heavy metals is accompanied by an increase in magnetic susceptibility χ. The presence of an electrowaste collection, processing, and sorting plant increases the content of trace elements in the soil in the area surrounding this pollutant emitter. Research has shown that there is an increased concentration of tellurium (Grygoyć and Jabłońska-Czapla 2021), as well as thallium and germanium, in soil. Our research showed that the germanium concentration in the studied area was as high as 7.64 mg.kg−1, with an average concentration of 3.51 mg.kg−1. Other studies on Saxony soils indicated that the germanium concentrations in two different soils were 1.5 and 1.6 mg.kg−1 (Wiche and Heilmeier 2016). Germanium content in soils is influenced by the natural content of this element in ores, such as zinc sulphide ores, and the germanium content may be in the range 1–500 mg.kg−1 (Zhang and Xu 2018). A study of the area around the abandoned Sb-As-Tl Allchar mine, in the Republic of Macedonia, demonstrated that soils contained a minimal 0.046 mg.kg−1 and a maximal 0.390 mg.kg−1 of germanium. In these areas, despite the increased human activity, the content of germanium is low, which is related to the natural formation of ores in this area (Beceva et al. 2014). Research into the content of germanium in soil samples with a thickness of 2–4 cm, collected in eastern China, showed that the average concentration of this element in this climatic region is 1 mg.kg−1 (Yang et al. 2010). In contrast, the concentration of germanium in soil sampled from Maui (Hawaiian Island) was approximately 2–3 mg.kg−1 (Scribner et al. 2006); the concentration of this element in soil from the Island of Hawaii was as high as 5.6 mg.kg−1 (Kurtz et al. 2002). A study of French forest soil showed that germanium concentrations were in the range 1.9–2.3 mg.kg−1 (converted from nmol.g−1) (Cornelis et al. 2010).
Results obtained from the previous testing of electrical waste treated in the WEEE facility, clearly showed that germanium content was the highest in the smallest fraction (< 0.1 mm) for all types of examined electrowaste elements. The content of Ge differed, depending on the type of electronic components and the main carriers of germanium were photo-resistors (2.59 mg·kg−1) (Willner et al. 2021). This study confirms that there is a significant impact of the processing of electrowaste (with a high content of germanium) on the increasing concentration of this element in the areas surrounding WEEE plants.
As part of this study, soil samples were also collected in areas not subjected to the pressure of e-waste processing, in an agricultural area in the vicinity of Lublin City (Poland). The average concentration of germanium in this area was 1.84 mg/kg. Research has shown that the germanium contamination of the area surrounding the electrowaste processing plant is caused by dust rising from the emitter, as indicated by the higher concentration of germanium in the prevailing wind direction in the area.
To check the correctness of the methodology for determining the concentration of elements in the soil, a certified reference material (NCS DC 73324) was used. Table S1 shows the concentration values of elements in the certified reference material and those measured in our research. Element recovery was in the range 91–110% and varied, depending on an individual element. The concentrations of the measured elements were in satisfactory agreement with the certified values.
The obtained results allowed the calculation of the correlation coefficients and created a correlation matrix, which is presented in Table S2. Many weak correlations were found between the concentration of germanium in soils and other elements, such as As, Sb, Ni, Sr, Cr, Al, Fe, and Mn. Correlation testing (Table S2) of germanium content with the pH and redox potential of the studied soils did not show a significant relationship. pH and redox potential were variable in a wide range. No strong correlation was found between soil pH, Eh and germanium concentration. The results also confirmed the correctness of the application of soil magnetometry for classifying soil sampling sites due to the correlation of magnetic susceptibility with the majority of heavy metals (Ni, Zn, Pb, Cr, Mo). The use of soil magnetometry to identify areas of heavy metal accumulation was used in the studies carried out by Rachwał et al. (2015, 2017a, b). Our research has confirmed that this method is also applicable to detect technology critical elements such as germanium. Soil samples with the highest content of germanium had very high magnetic susceptibility and there is a correlation between these parameters (Table S2).
4 Conclusion
In the studied area, germanium entered the environment during the recovery of electrowaste and it accumulated with other metals in the soil, mainly in the topsoil. Because of its widespread use in the semiconductor industry, there is a large amount of germanium in the waste at electrowaste treatment plants. This was confirmed by our previous research, in which the TCE content in electrowaste was determined (Willner et al. 2021). Germanium in electrowaste occurs as iGe, so the methyl derivatives found in the soil are most likely the result of methylation processes taking place in the soil itself. The highest concentration of germanium occurred in soil samples located north of the electrowaste processing and sorting plant, which is consistent with the prevailing wind direction in this area. Based on the obtained results, it can be stated that the most common germanium species, in areas under the pressure of a WEEE processing plant, was an inorganic form of germanium (Ge(IV)). However, in several samples with the highest concentration of this element, organic germanium species, such as MMGe and DMGe, were also found. The optimisation of the germanium extraction and speciation methodology in soil samples allowed for environmental studies of contaminated soils. The best extraction efficiency was obtained using 100 mM NH4NO3 with 1 mM potassium sodium tartrate as an extractant, washing out germanium from soils within 4 h. Optimised separation conditions enabled separation of the three germanium species (monomethylgermanium (MMGe), dimethylgermanium (DMGe), and Ge(IV)) using the Dionex IonPackTM As9-HC column. The use of IC-ICP-MS hyphenated techniques makes it possible to carry out a quick speciation analysis of a soil extract within 12 min. By using the ICP-MS spectrometer with a DRC-e reaction chamber, the interferences that have a negative effect on the determination of germanium with this technique are eliminated.
Our research confirmed the legitimacy of using soil magnetometry to determine the sampling sites of soils characterised by increased concentrations of metals and TCE. Soil samples with the highest content of germanium had very high magnetic susceptibility and there is a correlation between these parameters.
Due to the growing demand for new technologies, the global consumption of TCE, including germanium, has increased. In addition, drastic developments in the electrical and electronic industry, rapid consumption and the ‘aging’ of electrical and electronic equipment (requiring regular replacement) results in an increased amount of WEEE. For this reason, research on the impact of processes related to the recovery of electronic waste on various elements of the environment, including soil, is important and needed.
Availability of data and materials
Not applicable.
Sample availability
Samples of the compounds are available from the authors.
References
Beceva K, Stafilov T, Sajn R, Tanaselia C, Makreski P (2014) Distribution of chemical elements in soil and stream sediments in the area abandoned Sb-As-Tl Allchar mine, Republic of Macedonia. Environ Res 133:77–89. https://doi.org/10.1016/j.envres.2014.03.045
Belissont R, Boiron MC, Luais B, Cathelineau M (2014) LA-ICP-MS analyses of minor and trace elements and bulk Ge isotopes in zoned Ge-rich sphalerites from the Noailhac–Saint-Salvy deposit (France): insights into incorporation mechanisms and ore deposition processes. Geochim Cosmochim Acta 126:518–540. https://doi.org/10.1016/j.gca.2013.10.052
Cobelo-García A, Filella M, Croot P, Frazzoli C, Du Laing G, Ospina-Alvarez N, Rauch S, Salaun P, Schäfer J, Zimmermann S (2015) COST action TD1407: network on technology-critical elements (NOTICE) from environmental processes to human health threats. Environ Sci Pollut Res 22:15188–15194. https://doi.org/10.1007/s11356-015-5221-0
Cornelis JT, Delvaux B, Cardinal D, Andre L, Ranger J, Opfergelt S (2010) Tracing mechanisms controlling the release of dissolved silicon in forest soil solution using Si isotopes and Ge/Si ratios. Geochim Cosmochim Acta 74:3913–3924. https://doi.org/10.1016/j.gca.2010.04.056
Cui JI, Luo CL, Tang CWY, Chan TS, Li XD (2017) Speciation and leaching of trace metal contaminants from e-waste contaminated soils. J Hazard Mater 329:150–158. https://doi.org/10.1016/j.jhazmat.2016.12.060
D’Amore T, Miedico O, Pompa C, Preite C, Iammarino M, Nardelli V (2023) Characterization and quantification of arsenic species in foodstuffs of plant origin by HPLC/ICP-MS. Life 13(2):511. https://doi.org/10.3390/life13020511
Delvigne C, Opfergelt S, Cardinal D, Delvaux B, André L (2009) Distinct silicon and germanium pathways in the soil-plant system: evidence from banana and horsetail. J Geophys Res 114:G02013. https://doi.org/10.1029/2008JG000899
Delvigne C, Angeletti B, Guihou A, Basile-Doelsch I, Meunier JD (2017) Reliable determination of Ge in solid environmental samples using a chemical preparation procedure developed for Si isotopes and ICP-MS analysis. Geostand Geoanal Res 42(1):139–149. https://doi.org/10.1111/ggr.12197
Filella M, Rodríguez-Murillo JC (2017) Less-studied TCE: are their environmental concentrations increasing due to their use in new technologies? Chemosphere 182:605–616. https://doi.org/10.1016/j.chemosphere.2017.05.024
Filella M, Rodushkin I (2018) A concise guide for the determination of less-studied technology-critical elements (Nb, Ta, Ga, In, Ge, Te) by inductively coupled plasma mass spectrometry in environmental samples. Spectrochim Acta B 141:80–84. https://doi.org/10.1016/j.sab.2018.01.004
Fornalczyk A, Willner J, Jabłońska-Czapla M, Grygoyć K, Rachwał M (2019) Analysis of the content of germanium, tellurium and thallium in the grounded waste of electronic equipment. 16th International Conference on Environmental Science and Technology, CEST2019, Rhodes, Greece
García-Figueroa A, Filella M, Matoušek T (2021) Speciation of germanium in environmental water reference materials by hydride generation and cryotrapping in combination with ICP-MS/MS. Talanta 225:121972. https://doi.org/10.1016/j.talanta.2020.121972
Grygoyć K, Jabłońska-Czapla M (2021) Development of a Tellurium Speciation Study Using IC-ICP-MS on Soil Samples Taken from an Area Associated with the Storage, Processing, and Recovery of Electrowaste. Molecules 26:2651. https://doi.org/10.3390/molecules26092651
Hambrick GA, Froelich PN, Andreae MO, Lewis BL (1984) Determination of methylgermanium species in natural waters by graphite furnace atomic absorption spectrometry with hydride generation. Anal Chem 56(3):421–424. https://doi.org/10.1021/ac00267a027
Hirner AV, Grüter UM, Kresimon J (2000) Metal(loid)organic compounds in contaminated soil. 2000. Fresenius J Anal Chem 368:263–267. https://doi.org/10.1007/s002160000451
Işıldar A, Rene ER, van Hullebusch ED, Lens PNL (2018) Electronic waste as a secondary source of critical metals: Management and recovery technologies. Resour Conserv Recycl 135:296–312. https://doi.org/10.1016/j.resconrec.2017.07.031
Jabłońska-Czapla M, Grygoyć K (2022) Selected technology-critical elements as indicators of anthropogenic contamination of surface water and suspended solids on the example of the Biała Przemsza River (Poland). Chemosphere 307:135801. https://doi.org/10.1016/j.chemosphere.2022.135801
Jabłonska-Czapla M, Grygoyć K, Rachwał M, Fornalczyk A, Willner J (2022) Technology-critical elements (TCE) in soils in the areas around waste electrical and electronic equipment (WEEE) recycling plant. 10th Nordic Conference on Plasma Spectrochemistry, 12–15 Jun 2022, Loen, Norway, p 74
Jabłońska-Czapla M, Rachwał M, Grygoyć K, Fornalczyk A, Willner J, Zerzucha P (2021) Mobility of selected less studied technology critical elements (Ge, Te, Tl) in soils affected by the storage, processing and recovery of e-waste. Goldschmidt 2021 virtual conference, vol 5773. European Association of Geochemistry and the Geochemical Society. https://doi.org/10.7185/gold2021.5773
Julander A, Lundgren L, Skare LT, Grander M, Palm B (2014) Formal recycling of e-waste leads to increased exposure to toxic metals: an occupational exposure study from Sweden. Environ Int 73:243–251. https://doi.org/10.1016/j.envint.2014.07.006
Krystek P, Ritsema R (2004) Analtical product study of germanium-containing medicine by different ICP-MS applications. J Trace Elem Med Biol 18:9–16. https://doi.org/10.1016/j.jtemb.2004.04.003
Kurtz AC, Derry LA, Chadwick OA (2002) Germanium-silicon fractionation in the weathering environment. Geochim Cosmochim Acta 66(9):1525–1537. https://doi.org/10.1016/S0016-7037(01)00869-9
Lehmann F, Daus B, Reemtsma T (2019) Germanium speciation using liquid chromatograph- inductively coupled plasma-triple quadrupole mass spectrometry: Germanium in biological and chemical leaching solutions of fine-grained residues from copper smelting. J Chromatogr A 1593:47–53. https://doi.org/10.1016/j.chroma.2019.01.061
Nuss P, Blengini GA (2018) Towards better monitoring of technology critical elements in Europe: coupling of natural and anthropogenic cycles. Sci Total Environ 613–614:569–578. https://doi.org/10.1016/j.scitotenv.2017.09.117
Okoroafor PU, Mann L, Amin Ngu K, Zaffar N, Monei NL, Boldt C, Reitz T, Heilmeier H, Wiche O (2022) Impact of soil inoculation with bacillus amyloliquefaciens FZB42 on the phytoaccumulation of germanium, rare earth elements, and potentially toxic elements. Plants 11:341. https://doi.org/10.3390/plants11030341
Padro A, Rubio R, Rauret G (1995) Germanium speciation by LC-HG-ICP/OES. Fresenius J Anal Chem 351(4–5):449–453. https://doi.org/10.1007/BF00322917
Perkins DN, Brune Drisse MN, Nxele T, Sly PD (2014) E-waste: a global hazard. Ann Glob Health 80(4):286–295. https://doi.org/10.1016/j.aogh.2014.10.001
Rachwał M, Magiera T, Wawer M (2015) Coke industry and steel metallurgy as the source of soil contamination by technogenic magnetic particles, heavy metals and polycyclic aromatic hydrocarbons. Chemosphere 138:863–873. https://doi.org/10.1016/j.chemosphere.2014.11.077
Rachwał M, Kardel K, Magiera T, Bens O (2017a) Application of magnetic susceptibility in assessment of heavy metal contamination of Saxonian soil (Germany) caused by industrial dust deposition. Geoderma 295:10–21. https://doi.org/10.1016/j.geoderma.2017.02.007
Rachwał M, Wawer M, Magiera T, Steinnes E (2017b) Integration of soil magnetometry and geochemistry for assessment of human health risk from metallurgical slag dumps. Environ Sci Poll Res 24(34):26410–26423. https://doi.org/10.1007/s11356-017-0218-5
Romero-Freire A, Santos-Echeandia J, Neira P, Cobelo-Garcia A (2019) Less-studied technology-critical elements (Nb, Ta, Ga, In, Ge, Te) in the marine environment: review on their concentrations in water and organisms. Front Mar Sci 6:532. https://doi.org/10.3389/fmars.2019.00532
Rosenberg E (2007) Environmental speciation of germanium. Ecol Chem Eng 14(7):707–732
Rosenberg E (2009) Germanium: environmental occurrence, importance and speciation. Rev Environ Sci Biotechnol 8(1):29–57. https://doi.org/10.1007/s11157-008-9143-x
Scribner AM, Kurtz AC, Chadwick O (2006) Germanium sequestration by soil: targeting the roles of secondary clays and Fe-oxyhydroxides. Earth Planet Sci Lett 243:760–770. https://doi.org/10.1016/j.epsl.2006.01.051
Smichowski P, Marrero J (1998) Comparative study to evaluate the effect of different acids on the determination of germanium by hydride generation-inductively coupled plasma atomic emission spectrometry. Anal Chim Acta 376(3):283–291. https://doi.org/10.1016/S0003-2670(98)00556-X
Soylak M, Yigit S (2015) Preconcentration-separation of germanium at ultra trace levels on polysulfone membrane filter and its determination by spectrophotometry. J Ind Eng Chem 24:322–325. https://doi.org/10.1016/j.jiec.2014.10.003
Templeton DM, Fujishiro H (2017) Terminology of elemental speciation – an IUPAC perspective. Coord Chem Rev 352:424–431. https://doi.org/10.1016/j.ccr.2017.02.002
Thayer JS (2002) Biological methylation of less-studied elements. Appl Organomet Chem 16:677–691. https://doi.org/10.1002/aoc.375
Tricas E, Zachriadis GA, Rosenberg E (2014) Determination of bis-carboxyethyl germanium sesquioxide by gas chromatography with microwave induced plasma atomic emission detection after derivatization with alkyl chloroformates. Anal Bioanal Chem 406:3489–3496. https://doi.org/10.1007/s00216-014-7801-0
Wiche O, Heilmeier H (2016) Germanium (Ge) and rare earth element (REE) accumulation in selected energy crops cultivated on two different soils. Miner Eng 92:201–215. https://doi.org/10.1016/j.mineng.2016.03.023
Wiche O, Zertamni V, Hentschel W, Achtziger R, Midula P (2017) Germanium and rare earth elements in topsoil and soil-grown plants on different land use types in the mining area of Freiberg (Germany). J Geochem Explor 175(2–17):120–129. https://doi.org/10.1016/j.gexplo.2017.01.008
Wiche O, Szekely B, Moschner C, Helmeier H (2018) Germanium in the soil-plant system-a review. Environ Sci Pollut Res 25:31938–31956. https://doi.org/10.1007/s11356-018-3172-y
Willner J, Fornalczyk A, Jabłońska-Czapla M, Grygoyć K, Rachwał M (2021) Studies on the content of selected technology critical elements (germanium, tellurium and thallium) in electronic waste. Materials 14(13):3722. https://doi.org/10.3390/ma14133722
Wojcieszek J, Szpunar J, Lobinski R (2017) Speciation of technologically critical elements in the environment using chromatography with element and molecule specific detection. Trends Anal Chem 104:1–12. https://doi.org/10.1016/j.trac.2017.09.018
Yang T, Zhu Z, Ga Q, Rao Z, Han J, Wu Y (2010) Trace element geochemistry in topsoil from East China. Environ Earth Sci 60:623–631. https://doi.org/10.1007/s12665-009-0202-6
Yang L, Zhou X, Deng Y, Gong D, Luo H, Zhu P (2021) Dissipation behavior, residue distribution, and dietary risk assessment of fluopimomide and dimethomorph in taro using HPLC-MS/MS. Environ Sci Pollut Res 28:43956–43969. https://doi.org/10.1007/s11356-021-13713-z
Yellishetty M, Huston D, Graedel TE, Werner TT, Reck BK, Mudd GM (2017) Quantifying the potential for recoverable resources of gallium, germanium and antimony as companion metals in Australia. Ore Geol Rev 82:148–159. https://doi.org/10.1016/j.oregeorev.2016.11.020
Zhang L, Xu Z (2018) A critical review of material flow, recycling technologies, challenges and future strategy for scattered metals from minerals to wastes. J Clean Prod 202:1001–1025. https://doi.org/10.1016/j.jclepro.2018.08.073
Zhang J, Wang X, Dong Y, Xu Z (2017) Direct determination of trace germanium in river samples by CH4-Ar mixed gas plasma DRC-ICP-MS. Int J Mass Spectrom 421:184–188. https://doi.org/10.1016/j.ijms.2017.07.010
Funding
The research was carried out in the frame of the project which received funding from the National Science Centre of Poland based on the decision number UMO-2018/29/B/ST10/01522.
Author information
Authors and Affiliations
Contributions
Conceptualization Magdalena Jabłońska-Czapla; Data curation Magdalena Jabłońska-Czapla; Formal analysis Magdalena Jabłońska-Czapla, Katarzyna Grygoyć; Marzena Rachwał; Funding acquisition Magdalena Jabłońska-Czapla; Investigation Magdalena Jabłońska-Czapla, Katarzyna Grygoyć; Marzena Rachwał; Agnieszka Fornalczyk; Joanna Willner; Methodology Magdalena Jabłońska-Czapla, Katarzyna Grygoyć; Marzena Rachwał; Agnieszka Fornalczyk; Joanna Willner; Project administration Magdalena Jabłońska-Czapla; Resources Magdalena Jabłońska-Czapla, Katarzyna Grygoyć; Marzena Rachwał; Małgorzata Wawer Software Supervision Magdalena Jabłońska-Czapla, Katarzyna Grygoyć; Marzena Rachwał; Agnieszka Fornalczyk; Joanna Willner; Validation Magdalena Jabłońska-Czapla, Katarzyna Grygoyć; Marzena Rachwał; Agnieszka Fornalczyk; Joanna Willner; Visualization Magdalena Jabłońska-Czapla, Katarzyna Grygoyć; Marzena Rachwał; Agnieszka Fornalczyk; Joanna Willner; Roles/Writing – original draft Magdalena Jabłońska-Czapla, Katarzyna Grygoyć; Marzena Rachwał; Agnieszka Fornalczyk; Joanna Willner; Writing – review & editing Magdalena Jabłońska-Czapla, Katarzyna Grygoyć; Marzena Rachwał; Agnieszka Fornalczyk; Joanna Willner.
Corresponding author
Ethics declarations
Research with no involving human participants and/or animals
The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper.
Financial interests
The authors declare they have no financial interests.
Ethical approval
The Authors confirm that the manuscript entitled “Germanium speciation study in soil samples taken from an area associated with the storage, processing, and recovery of electrowaste” has not been published previously and is not under consideration for publication elsewhere.
Consent to participate
All authors agree to participate.
Consent to publish
All authors declare their consent to publication.
Conflict of interest
The authors declare no conflict of interest.
Additional information
Responsible editor: Claudio Colombo
Part of the study was presented at the 10th Nordic Conference on Plasma Spectrochemistry on June 12–15, 2022 in Loen, Norway as a poster presentation entitled Development of germanium speciation study using IC-ICP-MS technique in soil samples.
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Supplementary Information
Below is the link to the electronic supplementary material.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Jabłońska-Czapla, M., Grygoyć, K., Rachwał, M. et al. Germanium speciation study in soil from an electronic waste processing plant area. J Soils Sediments 23, 3362–3375 (2023). https://doi.org/10.1007/s11368-023-03566-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11368-023-03566-z