Abstract
The device called solar air heater (SAH) is used to collect and transfer solar-thermal energy to air that can further be used for space heating, drying, etc. The conventional air heater (solar-assisted) has poor performance, and with this work, an attempt has been made to improve its performance by providing surface roughness over the heated surface. The roughness employed over the surface has an elliptical cavity, and its distribution over the heated surface is defined with the three parameters (dimensionless): relative flow-wise distance (ranging from 6 to 14), relative cavity depth (ranging from 0.016 to 0.038), and relative crosswise distance (ranging from 6 to 14). A CFD code has been developed and validated with experimentation to do the parametric study for understanding the effect of the proposed surface roughness on the performance of the air heater. It is concluded that the proposed surface roughness promotes the local turbulence, flow separation, and strong vortices in the flow field resulting in comparatively higher thermal performance in the proposed air heater. But this higher thermal performance is achieved at the expense of higher-pressure loss in the passage. A substantial change in heat augmentation by 2.57 times (with 2.3 times higher pressure loss) which results in 1.75 times higher thermo-hydraulic performance has been noticed over conventional designs at a relative flow-wise distance of 10, relative cavity depth 0.038, and relative crosswise distance of 10.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
Data availability
NA.
Abbreviations
- D h :
-
Duct hydraulic diameter (m)
- h :
-
Convective heat transfer coefficient (W m−1 K−1)
- k :
-
Thermal conductivity (W m−1 K−1)
- P :
-
Pressure drop (Nm2)
- q″ :
-
Heat flux (W m−2)
- T :
-
Temperature (K)
- f m :
-
Average air mean
- p m :
-
Average plate
- t :
-
Test section (m)
References
Bhushan B, Singh R (2011) Nusselt number and friction factor correlations for solar air heater duct having artificially roughened absorber plate. Sol Energy 85(5):1109–1118. https://doi.org/10.1016/j.solener.2011.03.007
Biswas G, Eswaran V (2002) Turbulent flows fundamentals experiments and modeling. Narosa Publishing House, New Delhi
Burgess NK, Ligrani PM (2004) Effects of dimple depth on Nusselt numbers and friction factors for internal cooling in a channel, in: Turbo Expo: Power for Land, Sea, and Air 41685:989-998.https://doi.org/10.1115/GT2004-54232
Cebeci T, Bradshaw P (1988) Physical and computational aspects of convective heat transfer”. Springer-Verlag, Germany
Chhaparwal GK, Srivastava A, Dayal R (2019) Artificial repeated-rib roughness in a solar air heater – a review. Sol Energy 194:329–359. https://doi.org/10.1016/j.solener.2019.10.011
Choi EY, Choi YD, Lee WS, Chung JT, Kwak JS (2013) Heat transfer augmentation using a rib–dimple compound cooling technique. Appl Therm Eng 51(1–2):435–441. https://doi.org/10.1016/j.applthermaleng.2012.09.041
Choi SM, Kwon HG, Bang M, Moon HK, Cho HH (2021) Heat transfer from a dimple-imprint downstream of boundary-layer trip-wire. Int J Heat Mass Transfer 173:121242. https://doi.org/10.1016/j.ijheatmasstransfer.2021.121242
Chyu MK, Yu Y, Ding H, Downs JP, Soechting F (1997) Concavity enhanced heat transfer in an internal cooling passage. In: ASME 42nd international gas turbine and aero congress, ASME paper no. 97-GT-437, Orlando, FL. https://doi.org/10.1115/97-GT-437
Documentation, ANSYS Fluent (2016) “ANSYS Fluent Theory Guide.” ANSYS Help
Du W, Luo L, Wang S, Zhang X (2018) Effect of the dimple location and rotating number on the heat transfer and flow structure in a pin finned channel. Int J Heat Mass Transf 127:111–129. https://doi.org/10.1016/j.ijheatmasstransfer.2018.08.045
Eckert ERG, Low GM (1951) Temperature distribution in internally heated walls of heat exchangers composed of non-circular flow passages. NACA Rep 1022:383–396
Firoozi AO, Majidi S, Ameri M (2020) A numerical assessment on heat transfer and flow characteristics of nanofluid in tubes enhanced with a variety of dimple configurations. Therm Sci Eng Prog 19:100578. https://doi.org/10.1016/j.tsep.2020.100578
Goel V, Hans VS, Singh S, Kumar R, Pathak SK, Singla M, Bhattacharyya S, Almatrafi E, Gill RS, Saini RP (2021) A comprehensive study on the progressive development and applications of solar air heaters. Sol Energy 229:112–147. https://doi.org/10.1016/j.solener.2021.07.040
Hai DTH, Phu NM (2023) A critical review of all mathematical models developed for solar air heater analysis. J Adv Res Fluid Mech Ther Sci 105(1):1–14. https://doi.org/10.37934/arfmts.105.1.114
Hans VS, Saini RP, Saini JS (2009) Performance of artificial roughened solar air heaters - a review. Renew Sustain Energy Rev 13:1854–1869. https://doi.org/10.1016/j.rser.2009.01.030
Hassan AK, Hasan MM, Khan ME (2021) Parametric investigation and correlation development for heat transfer and friction factor in multiple arc dimple roughened solar air duct. Renew Energy 174:403–425. https://doi.org/10.1016/j.renene.2021.03.044
Hegde AK, Pai R, Karanth KV (2023) Performance augmentation of solar air heaters: a comprehensive analysis. Sol Energy 253:527–553. https://doi.org/10.1016/j.solener.2023.01.031
Isaev SA, Kornev NV, Leontiev AI, Hassel E (2010) Influence of the Reynolds number and the spherical dimple depth on turbulent heat transfer and hydraulic loss in a narrow channel. Int J Heat Mass Transf 53:178–197. https://doi.org/10.1016/j.ijheatmasstransfer.2009.09.042
Kumar V (2019) Nusselt number and friction factor correlations of three sides concave dimple roughened solar air heater. Renew Energy 135:355–377. https://doi.org/10.1016/j.renene.2018.12.002
Kumar R, Goel V (2021) Unconventional solar air heater with triangular flow-passage: A CFD based comparative performance assessment of different cross-sectional rib-roughnesses. Renewable Energy 172:1267–1278
Kumar V, Murmu R (2023) Performance based investigation of inclined spherical ball roughened solar air heater. Appl Therm Eng 224:120033. https://doi.org/10.1016/j.applthermaleng.2023.120033
Kumar V, Prasad L (2019) Thermal performance investigation of three sides concave dimple roughened solar air heaters. Sol Energy 188:361–379. https://doi.org/10.1016/j.solener.2019.06.008
Kumar R, Goel V, Kumar A (2016) Thermal and fluid dynamic characteristics of flow through triangular cross-sectional duct: a review. Renew Sustain Energy Rev 61:123–140. https://doi.org/10.1016/j.rser.2016.03.011
Kumar R, Goel V, Kumar A (2020) A note on the comparative analysis between rectangular and modified duct heat exchanger. J Heat Transfer 142(4):041901. https://doi.org/10.1115/1.4045755
Li M, Khan TS, Al Hajri E, Ayub ZH (2016) Geometric optimization for thermal hydraulic performance of dimpled enhanced tubes for single phase flow. Appl Therm Eng 103:639–650
Ligrani PM, Harrison JL, Mahmmod GI, Hill ML (2001) Flow structure due to dimple depressions on a channel surface. Phys Fluids 13(11):3442–3451. https://doi.org/10.1063/1.1404139
Lu G, Zhai X (2019) Analysis on heat transfer and pressure drop of a microchannel heat sink with dimples and vortex generators. Int J Therm Sci 145:105986. https://doi.org/10.1016/j.ijthermalsci.2019.105986
Luo L, Wen F, Wang L, Sunden B, Wang S (2017) On the solar receiver thermal enhancement by using the dimple combined with delta winglet vortex generator. Appl Therm Eng 111:586–598. https://doi.org/10.1016/j.applthermaleng.2016.09.096
Mahanand Y, Senapati JR (2021) Thermo-hydraulic performance analysis of a solar air heater (SAH) with quarter-circular ribs on the absorber plate: a comparative study. Int J Therm Sci 161:106747. https://doi.org/10.1016/j.ijthermalsci.2020.106747
Malhotra R, Singh B (2020) Design and construction of solar shed." In AIP Conference Proceedings. AIP Publishing LLC, 2220(1):140061. https://doi.org/10.1063/5.0001157
Manoram RB, Moorthy RS, Ragunathan R (2021) Investigation on influence of dimpled surfaces on heat transfer enhancement and friction factor in solar water heater. J Therm Anal Calorim 145(2):541–558. https://doi.org/10.1007/s10973-020-09746-0
Manual U.D.F. (2009) ANSYS Fluent 12.0. Theory Guide, p 67
Moon HK, O’Connell T, Glezer B (1999) Channel height effect on heat transfer and friction in a dimpled passage. In: ASME Turbo Expo, ASME 99-GT-163, Indianapolis. https://doi.org/10.1115/99-GT-163
Patankar SV (1980) Numerical heat transfer and fluid flow. Hemisphere, Washington DC
Perwez A, Kumar R (2019) Thermal performance investigation of the flat and spherical dimple absorber plate solar air heaters. Sol Energy 193:309–323. https://doi.org/10.1016/j.solener.2019.09.066
Prakash C, Saini RP (2019) Use of artificial roughness for performance enhancement of solar air heaters—a review. Int J Green Energy 16(7):551–572. https://doi.org/10.1080/15435075.2019.1598418
Rao Y, Feng Y, Li B, Weigand B (2015) Experimental and numerical study of heat transfer and flow friction in channels with dimples of different shapes. J Heat Transfer 137(3):031901. https://doi.org/10.1115/1.4029036
Rokni M, Gatski TB (2001) Predicting turbulent convective heat transfer in fully developed duct flows. Int J Heat Fluid Flow 22(4):381–392. https://doi.org/10.1016/S0142-727X(01)00104-7
Sabir R, Khan MM, Sheikh NA (2022) Numerical investigation of thermal-hydraulic performance of U-tubes enhanced with ellipsoidal 45 deg dimples. J Heat Transfer. https://doi.org/10.1115/1.4054555
Sahu MK, Priyam A, Mishra S, Bishnoi P (2021) A detailed review on research, technology, configurations and application of wire ribs as artificial roughness in rectangular solar air heater duct. Proc Inst Mech Eng Part E: J Process Mech Eng 235(4):1211–1234. https://doi.org/10.1177/0954408921995140
Sahu MK, Gorai VK, Saha BC (2023) Applications of extended surfaces for improvement in the performance of solar air heaters—a detailed systematic review. Environ Sci Pollut Res 30:54429–54447. https://doi.org/10.1007/s11356-023-26360-3
Sethi M, Thakur NS (2012) Correlations for solar air heater duct with dimpled shape roughness elements on absorber plate. Sol Energy 86(9):2852–2861. https://doi.org/10.1016/j.solener.2012.06.024
Shah RK, Dusan PS (2003) “Fundamentals of heat exchanger design.” John Wiley & Sons
Shui-lian L, Xiang-rui M, Xin-li W (2015) Heat transfer and friction factor correlations for solar air collectors with hemispherical protrusion artificial roughness on the absorber plate. Sol Energy 118:460–468. https://doi.org/10.1016/j.solener.2015.05.047
Singh S, Singh B, Hans VS, Gill RS (2015) CFD (computational fluid dynamics) investigation on Nusselt number and friction factor of solar air heater duct roughened with non-uniform cross-section transverse rib. Energy 84:509–517. https://doi.org/10.1016/j.energy.2015.03.015
Singh D, Singh A, Thakur A (2022) "Solar cogeneration in India: current situation and future prospects." In 2022 Third International Conference on Intelligent Computing Instrumentation and Control Technologies (ICICICT), pp. 1560–1565. IEEE. https://doi.org/10.1109/ICICICT54557.2022.9918001
Talukdar P, Shah M (2008) Analysis of laminar mixed convective heat transfer in horizontal triangular ducts. Numer Heat Transfer, Part A 54:1148–1168. https://doi.org/10.1080/10407780802552005
Webb RL, Eckert ERG (1972) Application of rough surface to heat exchanger design. Int J Heat Mass Transfer 15(9):1647–1658. https://doi.org/10.1016/0017-9310(72)90095-6
Welty J, Rorrer GL, Foster DG (2020) Fundamentals of momentum, heat, and mass transfer. John Wiley & Sons
Xie G, Liu J, Ligrani PM, Zhang W (2013) Numerical analysis of flow structure and heat transfer characteristics in square channels with different internal-protruded dimple geometrics. Int J Heat Mass Transf 67:81–97. https://doi.org/10.1016/j.ijheatmasstransfer.2013.07.094
Author information
Authors and Affiliations
Contributions
P. Srinivas Reddy: data extraction, writing—original draft, language, and review-editing. Rajneesh Kumar: methodology and simulations, Investigation, writing—original draft, language, and review-editing. Majeet Kharub: assisted in writing and data extraction and referencing. Gaurav Bharadwaj: assisted in writing and data extraction and referencing.
Corresponding author
Ethics declarations
Ethical approval
Hereby, I (Dr. Rajneesh Kumar) consciously assure that for the manuscript, “Application of triangular duct in solar assisted air-heating system with surface roughness: A numerical investigation,” the finding presented in this research report is the authors’ work, which has not been previously published elsewhere and the manuscript in part or in full has not been submitted or published anywhere.
Consent to participate
All the authors contributed their paper in writing this manuscript.
Consent for publication
With the mutual agreement of all the authors, it is decided that if this manuscript is accepted by the Editor-in-chief, it will be published in the Environmental Science and Pollution Research Journal.
Competing interests
There authors declare no competing interests.
Additional information
Responsible Editor: Philippe Garrigues
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Kumar, R., Reddy, P.S., Kharub, M. et al. Application of triangular duct in solar-assisted air-heating system with surface roughness: a numerical investigation. Environ Sci Pollut Res (2023). https://doi.org/10.1007/s11356-023-28794-1
Received:
Accepted:
Published:
DOI: https://doi.org/10.1007/s11356-023-28794-1