Skip to main content
SpringerLink
Log in

Development and Study of a Microprocessor-Equipped System for Monitoring the Rolling Forces on a Sheet Mill

  • Published:
Metallurgist Aims and scope

A new microprocessor-based system for monitoring rolling forces has been designed and built, the system making it possible to measure and record changes in the load on the rolls along sheet that is in the process of being rolled. Introduction of the monitoring system was the second stage in the modernization of the two high 150×235 mill in the laboratory of the Metal-Shaping Machines and Technologies Department at MAMI. The mill was then used to perform an experiment that made it possible to evaluate the effect of the draft and the contact-friction conditions on the deformational and force parameters in the rolling of copper sheet. The experimental results also confirmed the utility of the force-monitoring system that was developed.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3

Similar content being viewed by others

References

  1. A. P. Grudev, External Friction in Rolling, Metallurgiya, Moscow (1973).

  2. R. A. Shatalov, Theory of Rolling and Drawing Processes: Textbook, VZPI, Moscow (1993).

    Google Scholar 

  3. A. V. Zinov’ev, A. I. Kolpashnikov, P. I. Polukhin, et al., Metal-Forming Technology for Nonferrous Metals and Alloys, Metallurgiya, Moscow (1992).

    Google Scholar 

  4. M. A. Zaikov, V. P. Polukhin, A. M. Zaikov, and P. I. Smirnov, The Process of Rolling, MISiS, Moscow (2004).

    Google Scholar 

  5. S. Ionov and A. Zinov’ev, “Problems concerning friction and process lubricants in the cold rolling of sheet,” Proc. 5th Int. Sci-Pract. Conf. Scientifi c-Technical Progress in Metallurgy, Oct. 15–16, 2009, Temirtau, pp. 401–408.

  6. Yu. D. Zheleznov, S. L. Kotsar’, and A. G. Abiev, Statistical Studies of the Accuracy of Sheet Rolling, Metallurgiya, Moscow (1974).

Download references

Author information

Authors and Affiliations

  1. Moscow State University of Mechanical Engineering (MAMI), Moscow, Russia

    R. L. Shatalov & A. S. Lukash

  2. ITTs KROS Engineering and Technical Center, Ivanteevka, Moscow Oblast, Russia

    Yu. F. Timin

Authors
  1. R. L. Shatalov
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. A. S. Lukash
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Yu. F. Timin
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to R. L. Shatalov.

Additional information

Translated from Metallurg, No. 10, pp. 70–73, October, 2015.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Shatalov, R.L., Lukash, A.S. & Timin, Y.F. Development and Study of a Microprocessor-Equipped System for Monitoring the Rolling Forces on a Sheet Mill. Metallurgist 59, 948–952 (2016). https://doi.org/10.1007/s11015-016-0198-6

Download citation

  • Received:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s11015-016-0198-6

Keywords

Search

Navigation