Heat treatment parameters providing a required level of mechanical properties for different component parts are determined on the basis of experimental data about supercooled austenite transformation in engineering chromium-molybdenum steel, and also results of numerical modeling of variable cross-section components of this steel in a QForm 7 program.
Similar content being viewed by others
References
V.N. Nikitin, A. P. Shlyamnev, M. V. Nikitin, and M.N. Pankova, “New approach to the development of high-strength structural steels with ultimate strength of 1350 MPa or more,” Metallurgist, 55, No. 3/4, 171–176 (2011).
C. Moolwan and S. Netpu, “Failure analysis of a two high gearbox shaft,” Proc. Soc. Behav. Sci., 88, 154–163 (2013).
H. Bayrakceken, “Failure analysis of an automobile differential pinion shaft,” Eng. Fail. Anal., 13, 1422–1428 (2006).
Z. Pang, Sh. Yu, and J. Xu, “Study of effect of quenching deformation influenced by 17CrNiMo6 gear shaft of carburization,” Phys. Procedia, 50, 103–112 (2013).
H. R. B. Rad, A. Monshi, M. H. Idris, et al., “Premature failure analysis of forged cold back-up roll in a continuous tandem mill,” Mat. Design, 32, 4376–4384 (2011).
M. K. Lee, G. H. Kim, K. H. Kim, and W. W. Kim, “Control of surface hardnesses, hardening depths, and residual stresses of low carbon 12Cr steel by flame hardening,” Surf. Coat. Technol., 184, 239–246 (2004).
T. M. Loganathan, J. Purbolaksono, J. I. Inayat-Hussain, and N. Wahab, “Effects of carburization on expected fatigue life of alloys steel shafts,” Mat. Design, 32, 3544–3547 (2011).
A. Sugianto, M. Narazaki, M. Kogawara, et al., “Numerical simulation and experimental verification of carburizing quenching process of SCr420H steel helical gear,” J. Mater. Proc. Techn., 209, 3597–3609 (2009).
N. Limodin and Y. Verreman, “Fatigue strength improvement of a 4140 steel by gas nitriding: Influence of notch severity,” Mat. Sci. Eng. A, 435–436, 460–467 (2006).
S. Y. Sirin and E. Kaluc, “Structural surface characterization of ion nitrided AISI 4340 steel,” Mat. Design, 36, 741–747 (2012).
Y. Totik, R. Sadeler, H. Altun, and M. Gavgali, “The effects of induction hardening on wear properties of AISI 4140 steel in dry sliding conditions,” Mat. Design, 24, 25–30 (2003).
I. Magnabosco, P. Ferro, A. Tiziani, and F. Bonollo, “Induction heat treatment of a ISO C45 steel bar: Experimental and numerical analysis,” Comput. Mat. Sci., 35, 98–106 (2006.).
J. R. Welty, C. E. Wicks, R. E. Wilson, and G. L. Rorrer, Fundamentals of Momentum, Heat and Mass Transfer, John Wiley & Sons, NY USA (2008), 5th ed.
The work was carried out with partial financial of the UrFU within the scope of implementing a program for developing UrFU for winners of the “Young scientists of UrFU” competition. Results used in the work were obtained in the TsKP UrFU laboratory of structural analysis methods and nanomaterial properties.
Author information
Authors and Affiliations
Corresponding author
Additional information
Translated from Metallurg, No. 8, pp. 101–104, August, 2014.
Rights and permissions
About this article
Cite this article
Maisuradze, M.V., Ryzhkov, M.A., Yudin, Y.V. et al. Heat Treatment Technology for High-Strength Engineering Steel Variable Cross-Section Components. Metallurgist 58, 712–716 (2014). https://doi.org/10.1007/s11015-014-9982-3
Received:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11015-014-9982-3