Skip to main content
SpringerLink
Log in

Propagation of Low Frequency Ultrasonic Guided Waves Through Welded Lap Joint

  • Published:
Journal of Nondestructive Evaluation Aims and scope Submit manuscript

Abstract

Large storage tanks are heavily used to hold liquid in the oil and gas industry. The thickness mapping of the storage tank floor is carried out from inside the tank periodically during out-of-service inspection using a variety of non-destructive testing methods. Screening the storage tank bottom from the external annular ring to identify whether the tank requires further inspection or repair would save a significant amount of time. Currently, low frequency ultrasonic guided waves are routinely used to screen long sections of pipelines. Under the cut-off frequency of the first high-order mode, ultrasonic guided waves have the ability to propagate over long distances with minimal attenuation. However, multiple sources of attenuation are present in tank bottoms: (1) contact with fluid inside the tank, (2) contact with soil outside the tank, and (3) the floor assembly. Indeed, the floors of storage tanks are typically built using many overlapping welded steel plates. In the largest storage tanks, a line across the diameter may consist of up to 15 welded joints. Minimising the ultrasonic guided wave amplitude loss at each joint is therefore paramount to a successful screening. In this paper, the amplitude loss through welded lap joints is studied for the fundamental shear horizontal (SH0) and the fundamental symmetric Lamb wave (S0) modes. Using finite element simulations and experiments, the propagation of SH0 and S0 was studied in 12.7 mm steel plates welded in a lap joint configuration. The results show that the SH0 mode can be up to 6 dB higher than the S0 mode downstream of welded lap joints. Therefore, a careful selection of the mode and frequency may result in long propagation distances and may enable the screening of the floors using ultrasonic guided waves.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10

Similar content being viewed by others

Data Availability

Data and codes used in this study are openly available: https://pulets.ca/open-data/JONE-D-21-00059.

References

  1. Krausmann, E., Renni, E., Campedel, M., Cozzani, V.: Industrial accidents triggered by earthquakes, floods and lightning: lessons learned from a database analysis. Nat Hazards 59(1), 285–300 (2011). https://doi.org/10.1007/s11069-011-9754-3

    Article  Google Scholar 

  2. Pullen, A.L., Charlton, P.C., Pearson, N.R., Whitehead, N.J.: Magnetic flux leakage scanning velocities for tank floor inspection. IEEE Trans. Magn. 54(9), 1–8 (2018). https://doi.org/10.1109/TMAG.2018.2853117

    Article  Google Scholar 

  3. Laguerre, L., Treyssede, F.: Non destructive evaluation of seven-wire strands using ultrasonic guided waves. Eur. J. Environ. Civ. Eng. 15(4), 487–500 (2011). https://doi.org/10.1080/19648189.2011.9693342

    Article  Google Scholar 

  4. Alleyne, D.N., Pavlakovic, B., Lowe, M.J.S., Cawley, P.: Rapid, long range inspection of chemical plant pipework using guided waves. KEM 270–273, 434–441 (2004)

    Article  Google Scholar 

  5. Lowe, M.J.S., Alleyne, D.N., Cawley, P.: Defect detection in pipes using guided waves. Ultrasonics 36(1), 147–154 (1998). https://doi.org/10.1016/S0041-624X(97)00038-3

    Article  Google Scholar 

  6. Li, J.: On circumferential disposition of pipe defects by long-range ultrasonic guided waves. J. Pressure Vessel Technol. 127(4), 530–537 (2005). https://doi.org/10.1115/1.2083867

    Article  Google Scholar 

  7. Anastasopoulos, A.A., Kattis, S.E., Kourousis, D.A.: In-service inspection and structural integrity assessment of atmospheric storage tanks. Nondestructive Testing Mater Struct (2013). https://doi.org/10.1007/978-94-007-0723-8_127

    Article  Google Scholar 

  8. Lowe, P.S., Duan, W., Kanfoud, J., Gan, T.-H.: Structural health monitoring of above-ground storage tank floors by ultrasonic guided wave excitation on the tank wall. Sensors 17(11), 2542 (2017). https://doi.org/10.3390/s17112542

    Article  Google Scholar 

  9. Mazeika, L., Kazys, R., Raisutis, R., Sliteris, R.: Ultrasonic guided wave tomography for the inspection of the fuel tanks floor. IJMPT (2011). https://doi.org/10.1504/IJMPT.2011.040291

    Article  Google Scholar 

  10. Dimlaye, V., Mudge, P., Jackson, P., Tat-Hean, G., Soua, S.: Non-invasive structural health monitoring of storage tank floors. Aвтoмaтичecкaя cвapкa 10–11, 80–82 (2013)

    Google Scholar 

  11. Puchot, A.R., Cobb, A.C., Duffer, C.E., Light, G.M.: Inspection technique for above ground storage tank floors using MsS technology. AIP Conf. Proc. 1581(1), 844 (2015). https://doi.org/10.1063/1.4864909

    Article  Google Scholar 

  12. Chandrasekaran, J., Anto, I., Balasubramaniam, K., Venkataraman, K.S.: Higher order modes cluster (HOMC) guided waves for online defect detection in annular plate region of above-ground storage tanks. Insight Non-Destruct Testing Condition Monit 51(11), 606–611 (2009). https://doi.org/10.1784/insi.2009.51.11.606

    Article  Google Scholar 

  13. Lanza di Scalea, F., Rizzo, P., Marzani, A.: Propagation of ultrasonic guided waves in lap-shear adhesive joints: case of incident a0 Lamb wave. J Acoust Soc Am 115(1), 146–156 (2004). https://doi.org/10.1121/1.1630999

    Article  Google Scholar 

  14. Castaings, M.: SH ultrasonic guided waves for the evaluation of interfacial adhesion. Ultrasonics 54(7), 1760–1775 (2014). https://doi.org/10.1016/j.ultras.2014.03.002

    Article  Google Scholar 

  15. Comot, P., Bocher, P., Belanger, P.: Ultrasonic guided wave inspection of Inconel 625 brazed lap joints: simulation and experimentation. NDT E Int. 91, 71–78 (2017). https://doi.org/10.1016/j.ndteint.2017.06.007

    Article  Google Scholar 

  16. M. S. C. and S. J. Kim, “Reflection and Transmission of Normal Incidence SH0 Waves at a Lap Joint Consisting of Two Plates of the Same Material and Thickness,” Journal of the Korean Physical Society, vol. 49, no. 5, p. 1955, Nov. 2006.

  17. Siryabe, E., Renier, M., Meziane, A., Castaings, M.: The Transmission of lamb waves across adhesively bonded lap joints to evaluate interfacial adhesive properties. Phys. Procedia 70, 541–544 (2015). https://doi.org/10.1016/j.phpro.2015.08.012

    Article  Google Scholar 

  18. “Long Range Ultrasonic Testing for Large Storage Tanks.” https://www.twi-global.com/technical-knowledge/published-papers/condition-monitoring-of-large-oil-and-chemical-storage-tanks-using-long-range-ultrasonic-testing-lrut-june-2005.aspx. Accessed 12 Jan 2021.

  19. Jankauskas, A., Mazeika, L.: Ultrasonic guided wave propagation through welded lap joints. Metals 6(12), 315 (2016). https://doi.org/10.3390/met6120315

    Article  Google Scholar 

  20. “API 650 Welded Tanks for Oil Storage (thirteenth ed.).” API Publishing services, Washington, DC, 2020.

  21. Cheeke, J.D.N.: Fundamentals and applications of ultrasonic waves. CRC Press, 2017.

  22. Pavlakovic, B., Lowe, M., Alleyne, D., Cawley, P.: Disperse: a general purpose program for creating dispersion curves. In Thompson, D.O., Chimenti, D.E (eds.) Review of Progress in Quantitative Nondestructive Evaluation, pp. 185–192. Springer US, Boston, MA (1997)

  23. Huthwaite, P., Ribichini, R., Cawley, P., Lowe, M.J.S.: Mode selection for corrosion detection in pipes and vessels via guided wave tomography. IEEE Trans. Ultrason. Ferroelectr. Freq. Control 60(6), 1165–1177 (2013). https://doi.org/10.1109/TUFFC.2013.2679

    Article  Google Scholar 

  24. Belanger, P., Boivin, G.: Development of a low frequency omnidirectional piezoelectric shear horizontal wave transducer. Smart Mater. Struct. 25(4), 045024 (2016). https://doi.org/10.1088/0964-1726/25/4/045024

    Article  Google Scholar 

  25. Huthwaite, P., Zarogoulidis, K.: Pogo User’s Manual, p. 85.

  26. Huthwaite, P.: Accelerated finite element elastodynamic simulations using the GPU. J. Comput. Phys. 257, 687–707 (2014). https://doi.org/10.1016/j.jcp.2013.10.017

    Article  MathSciNet  MATH  Google Scholar 

  27. Drozdz, M.: Efficient numerical modelling of absorbing regions for boundaries of guided waves problems. In AIP Conference Proceedings, Brunswick, Maine (USA), vol. 820, pp. 126–133 (2006). doi: https://doi.org/10.1063/1.2184520

  28. R. D. Cook, B.D.: Concepts and applications of finite element analysis. Wiley, ISBN: 978-0-471-35605-90, 2002 [Online]. Available: https://repository.tudelft.nl/islandora/object/uuid%3A120dbf38-f47f-4625-ac39-c30724b0f84f. Accessed 30 Dec 2020

  29. Alleyne, D., Cawley, P.: A two-dimensional Fourier transform method for the measurement of propagating multimode signals. J Acoust Soc Am 89(3), 1159–1168 (1991). https://doi.org/10.1121/1.400530

    Article  Google Scholar 

  30. Boivin, G., Viens, M., Belanger, P.: Development of a low frequency shear horizontal piezoelectric transducer for the generation of plane SH waves. Minneapolis Minnesota 10(1063/1), 4940491 (2016)

    Google Scholar 

  31. Archambault, S.: Conception et Caractérisation d’un Système d’Imagerie Photoacoustique pour Application Biomédicale, 178.

  32. Seher, M., Nagy, P.B.: On the separation of Lorentz and magnetization forces in the transduction mechanism of Electromagnetic Acoustic Transducers (EMATs). NDT and E Int. 84, 1–10 (2016). https://doi.org/10.1016/j.ndteint.2016.07.001

    Article  Google Scholar 

  33. Lee, J.S., Kim, Y.Y., Cho, S.H.: Beam-focused shear-horizontal wave generation in a plate by a circular magnetostrictive patch transducer employing a planar solenoid array. Smart Mater. Struct. 18(1), 015009 (2009). https://doi.org/10.1088/0964-1726/18/1/015009

    Article  Google Scholar 

  34. Murayama, R.: Driving mechanism on magnetostrictive type electromagnetic acoustic transducer for symmetrical vertical-mode Lamb wave and for shear horizontal-mode plate wave. Ultrasonics 34(7), 729–736 (1996). https://doi.org/10.1016/0041-624X(96)00073-X

    Article  Google Scholar 

  35. Thompson, R.B.: Generation of horizontally polarized shear waves in ferromagnetic materials using magnetostrictively coupled meander-coil electromagnetic transducers. Appl. Phys. Lett. 34(2), 175–177 (1979). https://doi.org/10.1063/1.90719

    Article  Google Scholar 

  36. Glass, S.W., Lareau, J.P., Ross, K.S., Ali, S., Hernandez, F., Lopez, B.: Magnetostrictive cold spray sensor for harsh environment and long-term condition monitoring, p. 9.

  37. Kwun, H., Kim, S.Y.: Magnetostrictive sensor for generating and detecting plate guided waves. J. Pressure Vessel Technol. 127(3), 284–289 (2005). https://doi.org/10.1115/1.1991874

    Article  Google Scholar 

Download references

Acknowledgements

The authors would like to thank Nvidia for providing us with an Nvidia Quadro P6000 graphics card for our GPU simulations. This research was funded by Natural Sciences and Engineering Research Council of Canada (NSERC) grant number 544425-19 and Nucleom.

Funding

This research was funded by Natural Sciences and Engineering Research Council of Canada (NSERC) grant number 544425-19 and Nucleom.

Author information

Authors and Affiliations

  1. PULÉTS, École de Technologie Supérieure (ÉTS), Montréal, QC, H3C 1K3, Canada

    Aubin Chaboty, Frédéric Dupont-Marillia & Pierre Bélanger

Authors
  1. Aubin Chaboty
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Frédéric Dupont-Marillia
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Pierre Bélanger
    View author publications

    You can also search for this author in PubMed Google Scholar

Contributions

Conceptualization, AC and PB; methodology, AC; validation, PB and FD; formal analysis, AC, FD and PB; investigation, AC; writing original draft preparation, AC; writing review and editing AC, FD and PB; supervision, FD and PB; funding acquisition, PB All authors have read and agreed to the published version of the manuscript.

Corresponding author

Correspondence to Aubin Chaboty.

Ethics declarations

Conflict of Interest

The authors declare no conflict of interest.

Additional information

Publisher's Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Chaboty, A., Dupont-Marillia, F. & Bélanger, P. Propagation of Low Frequency Ultrasonic Guided Waves Through Welded Lap Joint. J Nondestruct Eval 40, 57 (2021). https://doi.org/10.1007/s10921-021-00788-4

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1007/s10921-021-00788-4

Keywords

Search

Navigation