Abstract
In general hydrogel synthesis uses a trial and error method when creating new hydrogels and searches afterwards for a fitting application of the received hydrogel. A much more effective and sustainable approach would be to have an application in mind before starting a targeted synthesis of a hydrogel with specific properties. Hence the goal of the study is to investigate influencing factors—crosslink density here represented through the degree of substitution, mass average molecular mass, mixing ratio and time for gelation—to the storage modulus \(G'\) for covalently cross-linked hydrogels based on oxidized cellulose sulfate and carboxymethyl chitosan. The results can be summarized as follows: higher values for \(G'\) can be reached by increasing the mass average molecular mass, the crosslink density and by shifting the mixing ratio toward the polymer which determines the number of possible cross-linkings in the hydrogel. The findings of this work may be transferred to similar systems and are helpful for a targeted synthesis of hydrogels with specific characteristics.
Similar content being viewed by others
Explore related subjects
Find the latest articles, discoveries, and news in related topics.Avoid common mistakes on your manuscript.
Introduction
In times of scarcer fossil raw resources and climate change the demand for sustainable materials increases drastically (Clark et al. 2009; Joseph and Tretsiakova-McNally 2010; Iwata 2015). Even in the field of hydrogels alternatives to fossil based products are favored and research is conducted (Simões et al. 2019). Therefore biopolymers become very attractive because they are widely available, renewable and biodegradable (Bashari et al. 2018; Maleki et al. 2016).
Cellulose and chitosan are one of the most abundant natural polymers (Abe and Higashi 1991; Lalani and Misra 2011) and so a great alternative as a parent substance for hydrogel synthesis.
Cellulose is the main component in plant cell walls. It consists of cellobiose monomers, which are connected through \(\beta\)-(1\(\rightarrow\)4)-glycosidic bonds to form a unbranched polymer chain that is insoluble in water. Chemical reactions happen mainly at the three hydroxyl groups of the anhydroglucose unit (AGU) where various functional groups can interact and change the properties of the cellulose. An example of this is the introduction of sulfate groups which even leads to a water soluble cellulose derivative (Wagenknecht et al. 1992).
Chitosan is the most important chitin derivate and is obtained under alkaline conditions by partial deacetylation of chitin (Chandy and Sharma 1990). It is constructed by \(\beta\)-(1\(\rightarrow\)4)-glycosidic linked D-glucosamines and N-acetyl-D-glucosamines, furthermore it is unbranched like cellulose. From a degree of deacetylation (DD) DD above 50% chitin becomes water soluble under acidic conditions and is called chitosan (Rinaudo 2006). Whereas cellulose has a plant based origin, most chitin and consequently chitosan is originated from crustaceans such as shrimp and crabs, where it is the structural element in the exoskeleton (Puvvada et al. 2012).
Using the example of cellulose and chitin one can see that derivatization leads to products with new properties. These properties define later possible applications. Generally, hydrogels can be found in all areas of life from wastewater treatment, where selected ions or bacteria are removed from the water (Mehrotra et al. 2020; Chauhan et al. 2007), over soil amendment to increase water retention and improve plant growth under drying climate stress (Mathes et al. 2020; Senna et al. 2015) up to tissue engineering (Daniele et al. 2014; Alsberg et al. 2001) and drug release (Juriga et al. 2019; Ashley et al. 2013).
In order to be able to synthesize hydrogels specifically for certain applications, and not the other way around to find an application for a specific hydrogel, influencing factors have to be well known. Influencing factors are not restricted to functional groups, they also include among others the degree of substitution (DS) and molecular weight of the polymer, the type of hydrogel (chemical or physical cross-linked) as well as the type of the formed network (Burdick and Murphy 2012; Ahmed 2015).
For that reason the aim of the study is to investigate potential influencing factors to the storage modulus \(G'\) for covalent cross-linked hydrogels consisting of oxidized cellulose sulfate (oCS) and carboxymethyl chitosan (CMCh). Here the impact of DS, mass average molecular mass (\(M_{\mathrm{w}}\)), mixing ratio and time for gelation on the storage modulus is studied.
Experimental
Chemicals and reagents
Sulfite pulp (\(DP_{\mathrm {W}}=1300\)) was received from Lenzing (Lenzing, Austria), cotten linters (\(DP_{\mathrm {W}}=6000\)) was received from Milouban (Ashrat, Israel). Carboxymethyl chitosan (\(DS=1\), \(DD =94.2\%\), \(M_{\mathrm{w}}=83.2\hbox { kDa}\)) was purchased from Heppe Medical Chitosan GmbH (Halle (Saale), Germany). Ethanol 99.5% denatured was purchased from Grüssing (Filsum, Germany), chlorosulfuric acid for synthesis and \(\hbox {KH}_{2}\hbox {PO}_{4}\) p.a. from Merck (Darmstadt, Germany), hydroxylammonium chloride technical was purchased from VWR (Darmstadt, Germany). Dimethylformamide (DMF) \(99\%\) and sodium periodate \(\ge 99.0\%\) were purchased from Sigma Aldrich (Munich, Germany), ethylene glycol \(\ge 99.5\%\) p.a., glacial acetic acid, potassium chloride \(\ge 99\%\), \(\hbox {Na}_{2}\hbox {HPO}_{4}\cdot \, 2\hbox { H}_{2}\hbox {O}\ge 99.5\%\) p. a., sodium chloride \(\ge 99.9\%\)\(\hbox {CELLPURE}^{\textregistered }\), sodium hydroxide and sodium acetate trihydrate were obtained from Carl Roth (Karlsruhe, Germany). DMF was dried over molecular sieve with a pore size of \(3\,\)Å. All other reagents were used without further purification. All aqueous solutions were prepared using deionized water. Dialysis membranes from \(\hbox {Spectra/Por}^{\textregistered }\) had a molecular weight cut off of 100 Da to 500 Da and of 3.5 kDa.
Sulfation and oxidation were conducted like described before (Strätz et al. 2019).
Sulfation of cellulose
For both variations of sulfation pretreatment was the following: Cellulose (2.50 g; 0.0154 mol) was soaked in 125 ml DMF at ambient temperature for 24 h. Dialysis was carried out using a standard regenerated cellulose membrane with a molecular weight cut off of 3.5 kDa.
Direct sulfation The reaction agent consisting of DMF (25 ml) and chlorosulfuric acid (0.0462 mol, 3.0 eq.; 0.0693 mol, 4.5 eq.; 0.0924 mol, 6.0 eq.) was prepared while cooling in an ice bath. The sulfating agent was added dropwise to the soaked cellulose at room temperature (RT). After 3 h of vigorous stirring the now clear solution was poured in an ethanolic solution (500 ml), which contained NaOH (14.3 g, 0.358 mol), \(\hbox {NaOAc}\cdot 3\hbox { H}_{2}\hbox {O}\) (11.05 g, 0.0812 mol) and \(\hbox {H}_{2}\hbox {O}\) (26.5 ml) filled up to 500 ml with ethanol (99%). The precipitate had to rest at least 12 h before the supernatant was removed by centrifugation. Afterwards the sediment was washed two times with 4% ethanolic/aqueous (v:v; 1:1) sodium acetate solution (100 ml). The product was dissolved in a minimum of \(\hbox {H}_{2}\hbox {O}\) and the pH was adjusted to 8.0 with glacial acetic acid. Next, the cellulose sulfate was precipitated and dissolved two more times, then dialyzed and lyophilized.
Acetosulfation The reaction agent consisting of DMF (25 ml), chlorosulfuric acid (0.0462 mol, 3.0 eq.) and acetic anhydride (0.123 mol, 8.0 eq.) was prepared while cooling in an ice bath. The sulfating agent was added dropwise to the soaked cellulose and heated to 50 °C, followed by 5 h of intense stirring at 50 °C. To quench the reaction the solution was poured in an ethanolic solution (500 ml) which contained NaOH (14.3 g, 0.358 mol), \(\hbox {NaOAc}\cdot 3\hbox { H}_{2}\hbox {O}\) (11.05 g, 0.0812 mol) and \(\hbox {H}_{2}\hbox {O}\) (26.5 ml) filled up to 500 ml with ethanol (99%). The precipitate had to rest at least 12 h before the supernatant was removed by centrifugation. The sediment was washed two times with 4% ethanolic/aqueous (v:v; 1:1) sodium acetate solution (100 ml). The product was then dissolved and stirred for 20 h at ambient temperature in NaOH (50 ml, 1 mol/l) for deacetylation, thereafter the pH was adjusted to 8.0 using glacial acetic acid. The (CS) was precipitated and dissolved two more times, then dialyzed and lyophilized.
Oxidation of cellulose sulfate
CS (1.5 g) was dissolved in water (60 ml) and sodium periodate (1.5 g; 0.007 mol; 1 weight equivalent) was added. The solution was stirred at ambient temperature under exclusion of light for 6 h. By adding ethylene glycol (1.5 ml; 0.027 mol) and stirring for another hour the reaction was quenched. The oCS was precipitated in ethanol (300 ml), dialyzed using a cellulose ester membrane with a molecular weight cut off of 100 Da to 500 Da and lyophilized to obtain a white solid product.
Cross-linking of oCS and CMCh
All gels had the same total concentration of 0.09 mmol/ml. Four different mixing ratios for oCS:CMCh (1:1; 1:3; 1:5; 1:10) were prepared. The ratio was calculated for the amount of substance of the aldehyd of the oCS and the corresponding amount of required CMCh.
oCS and CMCh were each dissolved in \(100\,\upmu \hbox {l}\) phosphate-buffered saline (PBS) (KCl (0.2 g), NaCl (8.0 g), \(\hbox {KH}_{2}\hbox {PO}_{4}\) (0.19 g) and \(\hbox {Na}_{2}\hbox {HPO}_{4}\cdot \, 2\hbox {H}_{2}\hbox {O}\) (0.765 g) filled up to 1 l with deionized water, afterwards the pH was adjusted with NaOH to 7.4). Then both solutions were mixed together 1:1 (v : v) in a vial and stirred at ambient temperature with a stirring rod until a colorless gel was obtained. The time until the colorless gel was formed is referred to as gelation time. The formed hydrogels rested for 24 h before they were overlaid with PBS (3 ml) for 24 h until the rheologic measurement.
Microwave digestion and ICP-OES
Dry CS (0,01 g) was mixed with hydrogen peroxide (2 ml; 30%) and nitric acid (3 ml; 65%). The microwave digestion was run with a Mars microwave by CEM (Kamp-Lintfort, Germany) using a two-step program. Step one: 1600 W, 100% power, temperature ramp 10 min, \(\vartheta =100\,^{\circ }\hbox {C}\), keep temperature for 5 min. Step two: 1600 W, 100% power, temperature ramp 10 min, \(\vartheta =180\,^{\circ }\hbox {C}\), keep temperature for 15 min.
The sulfur content was measured using the emission spectrometer Ciros CCD by Spectro (Kleve, Germany) with a plasma power of 1400 W and argon gas. The DS was calculated with Eq. 1 based on the determined sulfur content.
Determination of aldehyde content
A blank consisting of hydroxylammonium chloride (0.4 mol/l; 20 ml) and deionized water (25 ml) was made and the pH was measured. Dialyzed oCS (60.0 mg) was dissolved in deionized water (25 ml) and the pH was adjusted to 7.0 using sodium hydroxide (0.01 mol/l). After adding hydroxylammonium chloride (0.4 mol/l; 20 ml), the reaction mixture was stirred for a minimum of three hours at RT. The released HCl was titrated with NaOH (0.01 mol/l) until the pH of the blank was reached. The amount of aldehyde given as \(DS_{\mathrm{Ald}}\) was calculated by the following equation:
\(M_{\mathrm {C}}\) molar masse of carbon atom (12.01 g/mol), \(t_{\mathrm{NaOH}}\) titer of 0.01 mol/l NaOH, \(V_{\mathrm{NaOH}}\) volume of consumed 0.01 mole/l NaOH solution in ml, m: mass of sample in mg, \(C(\%)\) carbon content of sample in %, the carbon content was calculated taking account of \(DS_{\mathrm{Sulf}}\) instead of measuring the carbon content by elemental analysis.
Measurements
Size-exclusion chromatography (SEC) was performed on a Azura (Knauer, Germany) equipped with UV detector (UVD-2.1S) under following conditions: columns: Suprema precolumn, Suprema 1000, Suprema 30; column temperature: \(30.00\,^{\circ }\hbox {C}\); eluent: 0.1 mole/l \(\hbox {NaNO}_{3}/0.05\,\%\hbox { NaN}_{3}\); flowrate: 1.000 ml/min; standards: pullulan. All samples were filtered through a syringe filter (cellulose acetate, pore size \(0.45\,\upmu \hbox {m}\)) ahead the injection.
The frequency sweep was conducted using an Ares-G2 (TA Instruments) under following conditions: 15 mm parallel plate; temperature: \(25\,^{\circ }\hbox {C}\); strain: \(3.0 \cdot 10^{-3}\); logarithmic sweep; angular frequency: 0.1 rad/s to 100 rad/s.
SEM images were taken with an ESEM Quanta 650 FEG (FEI). Samples were lyophilized and then sputtered with gold using an ion sputter JFC 1100E (Jeol, Germany).
Results and discussion
The properties of hydrogels and the tuning of these plays an important role when it comes to possible application areas. This study is focused on \(G'\) and whereby it is influenced. An overview of the investigated samples and their properties is shown in Table 1.
At the beginning four parameters were chosen: \(DS_{\mathrm{Ald}}\), \(M_{\mathrm{w}}\), mixing ratio and time of gel formation. The \(DS_{\mathrm{Ald}}\) determines the number of possible cross-links since the number of amine groups in CMCh is much higher. \(G'\) should be influenced by the \(M_{\mathrm {W}}\) due to the chain length and needs to be examined. Regarding the mixing ratio it is interesting to know if a higher ratio of CMCh leads to a lower \(G'\) because of many unreacted and/or minimal crosslinked chitosan molecules. Due to the fact that the differences in time for gel formation are considerable, a potential relation between time for gel formation and \(G'\) was evaluated.
To make sure that just the four chosen parameters effect \(G'\) all gels had the same total concentration of 0.09 mmol/ml. Furthermore all hydrogels were swollen for 24 h to reach swelling equilibrium to have a defined state of swelling to compare the properties of the gels. Because without 24 h of swelling the gels would have different states of swelling depending on the number of possible cross-links for each sample.
As shown in Fig. 1 highest values for \(G'\) were reached by oCS with highest \(DS_{\mathrm{Ald}}\) independent of the mixing ratio. The result matches the expectation that a higher amount of cross-links leads to higher values of \(G'\). A highly crosslinked hydrogel cannot swell as much as a low crosslinked one, for this reason highly crosslinked hydrogels are stiffer and reach higher \(G'\) (Schacht et al. 1997). In Fig. 2 are SEM images of freeze-dried hydrogels of the samples 1 and 3 with a \(DS_{\mathrm{Ald}}\) of 0.34 and 0.09 presented to illustrate the differences in swelling and to understand the variation in their \(G'\). When looking at Fig. 2c and comparing with Fig. 2d the low crosslinked sample 3 features a lot more cavities than the higher crosslinked sample 1.
While the amount of possible cross-links is at least three times as much for the samples with \(DS_{\mathrm{Ald}}= 0.33\) and \(DS_{\mathrm{Ald}}= 0.34\) in comparison to the other, the variation in \(G'\) is broadly distributed. This observation might have its cause in one of the other studied parameters.
When looking at Fig. 3 one can see that with increasing \(M_{\mathrm{w}}\)\(G'\) increases as well. The influence of \(M_{\mathrm{w}}\) on \(G'\) outweighs the influence of the \(DS_{\mathrm{Ald}}\) as you see when comparing the samples with the \(DS_{\mathrm{Ald}}= 0.33\) and \(DS_{\mathrm{Ald}}=0.34\). Although the samples with the highest \(M_{\mathrm{w}}\) also have the highest \(DS_{\mathrm{Ald}}\) the same effect can be noticed for the samples with \(DS_{\mathrm{Ald}}= 0.10\) and \(DS_{\mathrm{Ald}}= 0.11\).
Additionally to the covalent bonds between oCS and CMCh polymer entanglement might also contribute to the gel formation and the stiffness of the resulting hydrogel (Tsukeshiba et al. 2005). Longer polymer chains have more possibilities of entanglement than shorter ones which is another reason why the \(M_{\mathrm{w}}\) influences \(G'\).
Another factor that should be considered is the time needed for gel formation. The here shown hydrogels can be categorized in three groups: (1) less than 1 min of gel formation, (2) 6 h to 12 h of gel formation and (3) 24 h of gel formation. The samples with shortest gelation time show the highest values for \(G'\) (Fig. 4) independent of the mixing ratio. Moreover the gelation time correlates with \(DS_{\mathrm{Ald}}\), with increasing gelation time the \(DS_{\mathrm{Ald}}\) decreases. An explanation for this is that with increasing \(DS_{\mathrm{Ald}}\) the number of possible cross-links increase and thus a faster formation of covalent bonds is possible which results in a shorter gelation time. The relation between \(DS_{\mathrm{Ald}}\) and \(G'\) was discussed earlier.
Regarding the mixing ratio the expectation, that a higher amount of CMCh leads to lower \(G'\), was approved independent of other factors here \(DS_{\mathrm{Ald}}\) and \(M_{\mathrm{w}}\) (Figs. 1 and 3). To reach as high as possible values for \(G'\) the mixing ratio should be shifted toward the polymer which determines the number of possible cross-linkings in the hydrogel to minimize the number of unreacted molecules. The variety of mixing ratios was strongly limited due to the solubility of oCS and CMCh. But it was found that for a better miscibility of the two components their volumes should be equal. Otherwise instead of a colorless hydrogel a white sediment was received.
Conclusion
It could be shown that for hydrogels consisting of oCS and CMCh \(G'\) is dependent on the crosslink density, which is represented by the \(DS_{\mathrm{Ald}}\). Higher values for \(DS_{\mathrm{Ald}}\) result in higher values for \(G'\), because the number of possible cross-linkings increases with rising \(DS_{\mathrm{Ald}}\). Furthermore the storage modulus increases also when the \(M_{\mathrm{w}}\) of the used polymer is raised due to increasing polymer entanglement. Moreover the mixing ratio of the gel forming components should be shifted toward the polymer which determines the number of possible cross-linkings in the hydrogel when aiming for a high value of \(G'\).
The findings of this study are helpful for a targeted synthesis of hydrogels with specific properties and may be transferred to similar systems.
References
Abe T, Higashi M (1991) Cellulose centered perspective on terrestrial community structure. Oikos 60(1):127–133
Ahmed EM (2015) Hydrogel: preparation, characterization, and applications: a review. J Adv Res 6(2):105–121. https://doi.org/10.1016/j.jare.2013.07.006
Alsberg E, Anderson K, Albeiruti A, Franceschi R, Mooney D (2001) Cell-interactive alginate hydrogels for bone tissue engineering. J Dent Res 80(11):2025–2029. https://doi.org/10.1177/00220345010800111501
Ashley GW, Henise J, Reid R, Santi DV (2013) Hydrogel drug delivery system with predictable and tunable drug release and degradation rates. Proc Natl Acad Sci 110(6):2318–2323. https://doi.org/10.1073/pnas.1215498110
Bashari A, Rouhani Shirvan A, Shakeri M (2018) Cellulose-based hydrogels for personal care products. Polym Adv Technol 29(12):2853–2867. https://doi.org/10.1002/pat.4290
Burdick JA, Murphy WL (2012) Moving from static to dynamic complexity in hydrogel design. Nat Commun 3(1):1–8. https://doi.org/10.1038/ncomms2271
Chandy T, Sharma CP (1990) Chitosan-as a biomaterial. Biomater Artif Cells Artif Org 18(1):1–24. https://doi.org/10.3109/10731199009117286
Chauhan GS, Chauhan K, Chauhan S, Kumar S, Kumari A (2007) Functionalization of pine needles by carboxymethylation and network formation for use as supports in the adsorption of Cr6+. Carbohydr Polym 70(4):415–421. https://doi.org/10.1016/j.carbpol.2007.04.020
Clark JH, Deswarte FEI, Farmer TJ (2009) The integration of green chemistry into future biorefineries. Biofuels Bioprod Biorefining 3(1):72–90. https://doi.org/10.1002/bbb.119
Daniele MA, Adams AA, Naciri J, North SH, Ligler FS (2014) Interpenetrating networks based on gelatin methacrylamide and peg formed using concurrent thiol click chemistries for hydrogel tissue engineering scaffolds. Biomaterials 35(6):1845–1856. https://doi.org/10.1016/j.biomaterials.2013.11.009
Iwata T (2015) Biodegradable and bio-based polymers: future prospects of eco-friendly plastics. Angew Chem Int Ed 54(11):3210–3215. https://doi.org/10.1002/anie.201410770
Joseph P, Tretsiakova-McNally S (2010) Sustainable non-metallic building materials. Sustainability 2(2):400–427. https://doi.org/10.3390/su2020400
Juriga D, Sipos E, Hegedűs O, Varga G, Zrínyi M, Nagy KS, Jedlovszky-Hajdú A (2019) Fully amino acid-based hydrogel as potential scaffold for cell culturing and drug delivery. Beilstein J Nanotechnol 10:2579–2593. https://doi.org/10.3762/bjnano.10.249
Lalani J, Misra A (2011) 4–gene delivery using chemical methods. In: Misra A (ed) Challenges in delivery of therapeutic genomics and proteomics. Elsevier, London, pp 127–206. https://doi.org/10.1016/B978-0-12-384964-9.00004-9
Maleki L, Edlund U, Albertsson AC (2016) Green semi-ipn hydrogels by direct utilization of crude wood hydrolysates. ACS Sustain Chem Eng 4(8):4370–4377. https://doi.org/10.1021/acssuschemeng.6b00938
Mathes F, Murugaraj P, Bougoure J, Pham VT, Truong VK, Seufert M, Wissemeier AH, Mainwaring DE, Murphy DV (2020) Engineering rhizobacterial community resilience with mannose nanofibril hydrogels towards maintaining grain production under drying climate stress. Soil Biol Biochem. https://doi.org/10.1016/j.soilbio.2020.107715
Mehrotra T, Zaman MN, Prasad BB, Shukla A, Aggarwal S, Singh R (2020) Rapid immobilization of viable bacillus pseudomycoides in polyvinyl alcohol/glutaraldehyde hydrogel for biological treatment of municipal wastewater. Environ Sci Pollut Res. https://doi.org/10.1007/s11356-019-07296-z
Puvvada YS, Vankayalapati S, Sukhavasi S (2012) Extraction of chitin from chitosan from exoskeleton of shrimp for application in the pharmaceutical industry. Int Curr Pharm J 1(9):258–263. https://doi.org/10.3329/icpj.v1i9.11616
Rinaudo M (2006) Chitin and chitosan: properties and applications. Prog Polym Sci 31(7):603–632. https://doi.org/10.1016/j.progpolymsci.2006.06.001
Schacht E, Bogdanov B, Bulcke AVD, Rooze ND (1997) Hydrogels prepared by crosslinking of gelatin with dextran dialdehyde. React Funct Polym 33(2):109–116. https://doi.org/10.1016/S1381-5148(97)00047-3
Senna AM, do Carmo JB, da Silva JMS, Botaro VR (2015) Synthesis, characterization and application of hydrogel derived from cellulose acetate as a substrate for slow-release npk fertilizer and water retention in soil. J Environ Chem Eng 3(2):996–1002. https://doi.org/10.1016/j.jece.2015.03.008
Simões BM, Cagnin C, Yamashita F, Olivato JB, Garcia PS, de Oliveira SM, Grossmann MVE (2019) Citric acid as crosslinking agent in starch/xanthan gum hydrogels produced by extrusion and thermopressing. LWT. https://doi.org/10.1016/j.lwt.2019.108950
Strätz J, Liedmann A, Trutschel ML, Mäder K, Groth T, Fischer S (2019) Development of hydrogels based on oxidized cellulose sulfates and carboxymethyl chitosan. Cellulose 26(12):7371–7382
Tsukeshiba H, Huang M, Na YH, Kurokawa T, Kuwabara R, Tanaka Y, Furukawa H, Osada Y, Gong JP (2005) Effect of polymer entanglement on the toughening of double network hydrogels. J Phys Chem B 109(34):16304–16309. https://doi.org/10.1021/jp052419n
Wagenknecht W, Nehls I, Stein A, Klemm D, Philipp B (1992) Synthesis and substituent distribution of na-cellulose sulphates via o-trimethylsilyl cellulose as intermediate. Acta Polym 43(5):266–269. https://doi.org/10.1002/actp.1992.010430505
Acknowledgments
Open Access funding provided by Projekt DEAL. We thank Harald Rohm and Norbert Raak for the possibility and support to do the rheological measurements and Björn Günther for taking the SEM images. This work was financially supported by Deutsche Forschungsgemeinschaft (grant number FI 755/10-1).
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no conflict of interest.
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
About this article
Cite this article
Strätz, J., Fischer, S. Tailored covalently cross-linked hydrogels based on oxidized cellulose sulfate and carboxymethyl chitosan by targeted adjustment of the storage modulus. Cellulose 27, 7535–7542 (2020). https://doi.org/10.1007/s10570-020-03279-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10570-020-03279-3