Abstract
The drilling rate index (DRI) is an important parameter that influences the drillability of rocks. It can easily be used when estimating the economics of any excavation operation. Therefore, in the current study, an attempt was made to investigate the rock properties that govern the DRI. The relationships between the DRI and some physicomechanical rock properties were investigated based on data obtained from experimental work and in situ studies performed in different tunnels. Regression analysis was employed to develop models for estimating the DRI based on physicomechanical rock properties. The derived models were verified based on the behavior of the determination coefficient, the t test, and the F test. The study showed that the DRI decreases with increasing uniaxial compressive strength, point load strength, Brazilian tensile strength, and Schmidt rebound hardness. It was also concluded that the DRI increases with increasing apparent porosity and void ratio. Additionally, modeling results revealed that the proposed models can be successfully used as tools to forecast the DRI.
Similar content being viewed by others
References
Akun ME, Karpuz C (2005) Drillability studies of surface-set diamond drilling in Zonguldak Region sandstones from Turkey. Int J Rock Mech Min Sci 42:473–479
ASTM (2005) Standard test method for determination of rock hardness by rebound hammer method, D873-05. American Standards for Testing and Materials, West Conshohocken
ASTM (2010a) Standard test method for compressive strength and elastic moduli of intact rock core specimens under varying states of stress and temperatures, D7012-10. American Standards for Testing and Materials, West Conshohocken
ASTM (2010b) Standard test methods for apparent porosity, water absorption, apparent specific gravity, and bulk density of burned refractory brick and shapes by boiling water, C20-00. American Standards for Testing and Materials, West Conshohocken
Aydin G (2014) Modeling of energy consumption based on economic and demographic factors: the case of Turkey with projections. Renew Sustain Energy Rev 35:382–389
Aydin G, Karakurt I, Aydiner K (2013a) Investigation of the surface roughness of rocks sawn by diamond sawblades. Int J Rock Mech Min Sci 61:171–182
Aydin G, Karakurt I, Aydiner K (2013b) Wear performance of saw blades in processing of granitic rocks and development of models for wear estimation. Rock Mech Rock Eng 46(6):1559–1575
Berman ME, Wang J (2011) Essential statistics for public managers and policy analysts, 3rd edn. CQ, Washington, DC, p 321
Bilgin N, Kahraman S (2003) Drillability prediction in rotary blast hole drilling. In: 18th Int Mining Congr Exhib Turkey (IMCET 2003), Antalya, Turkey, 10–13 June 2003, pp 177–182
Bruland A (1998) Hard rock tunnel boring, drillability test methods, project report 13A-98. Trondheim, NTNU, p 25
Bruland A, Dahlo TS, Nilsen B (1995) Tunnelling performance estimation based on drillability testing. In: Proc 8th Int Congr Rock Mech, Tokyo, Japan, 25–30 Sept 1995, pp 123–126
Capik M, Yilmaz AO, Yasar S, Yarali O, Cavusoglu I (2013) Comparison of drillability and abrasivity properties of rocks (in Turkish). In: 23rd Int Mining Congr Exhib Turkey (IMCET 2013), Antalya, Turkey, 16–19 April 2013, pp 659–669
Dahl F (2003) DRI, BWI, CLI standards. NTNU, Trondheim, p 20
Dahl F, Grøv E, Breivik T (2007) Development of a new direct test method for estimating cutter life, based on the Sievers’ J miniature drill test (technical note). Tunn Undergr Space Technol 22:106–116
Dahl F, Bruland A, Grov E, Nilsen B (2010) Trademarking the NTNU/SINTEF drillability test indices. Tunnels Tunn Int 44–46
Dahl F, Bruland A, Jakobsen PD, Nilsen B, Grøv E (2012) Classifications of properties influencing the drillability of rocks, based on the NTNU/SINTEF test method. Tunn Undergr Space Technol 28:150–158
Demirdağ S, Sengün N, Uğur İ, Efe T, Akbay D, Altindağ R (2014) Variation of vertical and horizontal drilling rates depending on some rock properties in the marble quarries. Int J Min Sci Technol 24:269–273
Ersoy A, Waller MD (1995) Textural characterization of rocks. Eng Geol 39:123–136
Franklin JA, Vogler UW, Szlavin J, Edmond JM, Bieniawski ZT (2007) Suggested methods for determining water-content, porosity, density, absorption and related properties and swelling and slake-durability index properties. In: Ulusay R, Hudson JA (eds) The complete ISRM suggested methods for rock characterization, testing and monitoring; 1974–2006. ISRM Turkish National Group, Ankara, pp 83–98
Hoseinie SH, Aghababaei H, Pourrahimian Y (2008) Development of a new classification system for assessing of rock mass drillability index (RDi). Int J Rock Mech Min Sci 45:1–10
Howarth DF, Rowland JC (1987) Quantitative assessment of rock texture and correlation with drillability and strength properties. Rock Mech Rock Eng 20:57–85
ISRM (1979) Suggested method for determining the uniaxial compressive strength and deformability of rock materials. Int J Rock Mech Min Sci Geomech Abstr 16:135–140
ISRM (1981) Suggested methods for determining hardness and abrasiveness of rocks. In: Ulusay R, Hudson JA (eds) The complete ISRM suggested methods for rock characterization, testing and monitoring; 1974–2006. ISRM Turkish National Group, Ankara, 3:101–103
ISRM (1985) Suggested method for determining point load strength. Int J Rock Mech Min Sci Geomech Abstr 22:51–60
Kahraman S, Balci C, Yazici S, Bilgin N (2000) Prediction of the penetration rate of rotary blast hole drilling using a new drillability index. Int J Rock Mech Min Sci 37:729–743
Lien R (1961) An indirect test method for estimating the drillability of rocks. Doctoral dissertation. Department of Geology, NTH, Trondheim
Saeidi O, Torabi SR, Ataei M (2013) Development of a new index to assess the rock mass drillability. Geotech Geol Eng 31:1477–1495
Singh TN, Gupta AR, Sain R (2006) A comparative analysis of cognitive system for the prediction of drillability of rocks and wear factor. Geotech Geol Eng 24:299–312
Thuro K (1996) Drillability prediction in hard rock tunnelling. In: Conf on Prediction in Geology, Amsterdam, Netherlands, 22–24 Feb 1996, pp 103–108
Thuro K (1997) Drillability prediction—geological influences in hard rock drill and blast tunneling. Geol Rundsch 86:426–438
Thuro K, Spaun G (1996) Drillability in hard rock drill and blast tunneling. Felsbau 14(2):1–11
Yaralı O (2008) Kayaçların Delinebilirlik ve Aşındırıcılıklarının Belirlenmesi. Türkiye 16. Kömür Kongresi Bildiriler Kitabı. TMMOB Maden Mühendisleri Odası Yayını, Zonguldak, pp 65–76
Yaralı O, Kahraman S (2011) The drillability assessment of rocks using the different brittleness values. Tunn Undergr Space Technol 26:406–414
Yarali O, Soyer E (2013) Assessment of relationships between drilling rate index and mechanical properties of rocks. Tunn Undergr Space Technol 33:46–53
Yasar S, Capik M, Yılmaz AO (2015) Cuttability assessment using the drilling rate index (DRI). Bull Eng Geol Environ 74:1349. doi:10.1007/s10064-014-0715-4
Zare S, Bruland A (2013) Applications of NTNU/SINTEF drillability indices in hard rock tunneling. Rock Mech Rock Eng 46:179–187
Acknowledgements
The authors would like to thank the Scientific Research Projects Unit of Karadeniz Technical University for financial support (project number: 8683). The authors also greatly appreciate the permission given by the NAS-YSE and AS-YOL Construction Company to collect data in the tunnels. Most of the DRI tests were carried out in Bulent Ecevit University with the generous assistance of Assoc. Prof. Dr. Olgay Yarali and his crew. In addition, the authors wish to thank Asst. Prof. Gokhan Aydin for his suggestions for improving the quality of the manuscript. Finally, the authors gratefully acknowledge Prof. Bjorn Nilsen, Prof. Amund Bruland, and Filip Dahl.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Capik, M., Yilmaz, A.O. & Yasar, S. Relationships between the drilling rate index and physicomechanical rock properties. Bull Eng Geol Environ 76, 253–261 (2017). https://doi.org/10.1007/s10064-016-0991-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s10064-016-0991-2