Abstract
Laser welding is a feasible process for joining the additive manufactured (AMed) parts to meet the manufacturing demand of specific large-scale components. Microstructure and property evolution as well as weldability of the laser welding of wire arc additive manufactured (WAAMed) Al-Cu alloy are investigated. Results indicate that the WAAMed Al-Cu alloy has excellent laser weldability and the joint is nearly free of defect. The width of the heat-affected-zone (HAZ) and equiaxed crystal zone (EQZ) as well as the grain size of the fusion zone (FZ) will increase with higher laser power and heat input. The joint with laser power of 3500 W has the highest tensile strength and elongation, reaching 203.48 MPa and 4.13%. The result from electron backscatter diffraction (EBSD) test indicates that the texture intensity will affect tensile properties. The tensile strength and elongation of the laser welded WAAM sample perpendicular to the deposition direction are higher than that parallel to the deposition direction. The microhardness value of HAZ is higher than that of FZ and BM due to 163 HV. The feasibility of laser welding of WAAMed samples is validated, and process parameters are found for hybrid manufacturing of large-scale components.
Similar content being viewed by others
Data availability
The authors confirm that the data supporting the findings of this study are available within the article.
Code availability
Not applicable.
References
Sellamuthu P, Reddy PS, Ramesh R, Kiranmai MH, Gupta CLN, Das AD, Subbiah R (2022) Surface investigation on aluminium composite by additive manufacturing process. Mater Today. https://doi.org/10.1016/j.matpr.2022.07.249
Jiangang P, Bo Y, Jinguo G, Yu R, Hongjun C, Liang Z, Hao L (2022) Influence of arc mode on the microstructure and mechanical properties of 5356 aluminum alloy fabricated by wire arc additive manufacturing. J Market Res 20:1893–1907. https://doi.org/10.1016/j.jmrt.2022.08.005
Arana M, Ukar E, Rodriguez I, Aguilar D, Álvarez P (2022) Influence of deposition strategy and heat treatment on mechanical properties and microstructure of 2319 aluminium WAAM components. Mater Des 221. https://doi.org/10.1016/j.matdes.2022.110974
Sinha AK, Pramanik S, Yagati KP (2022) Research progress in arc based additive manufacturing of aluminium alloys – a review. Measurement 200. https://doi.org/10.1016/j.measurement.2022.111672
Jianglong Gu, Ding J, Williams SW, Huimin Gu, Ma P, Zhai Y (2016) The effect of inter-layer cold working and post-deposition heat treatment on porosity in additively manufactured aluminum alloys. J Mater Process Technol 230:26–34. https://doi.org/10.1016/j.jmatprotec.2015.11.006
Cui X, Qi E, Sun Z, Jia C, Zeng Y, Wu S (2022) Wire oscillating laser additive manufacturing of 2319 aluminum alloy: optimization of process parameters, microstructure, and mechanical properties. Addit Manuf Front, Chin J Mech Eng. https://doi.org/10.1016/j.cjmeam.2022.100035
Xie R, Liang T, Shi Y, Liu H (2022) Revealing the bonding mechanisms between deposit and substrate of the friction rolling additive manufactured hybrid aluminum alloys. Addit Manuf 56. https://doi.org/10.1016/j.addma.2022.102942
Gao Z, Hengchang Bu, Feng Yu, Lyu F, Zhan X (2021) Strengthening mechanism of Y2O3 nanoparticles on microstructure and mechanical properties of the laser additive manufacturing joint for large thickness TC4 titanium alloy. J Manuf Process 71:37–55. https://doi.org/10.1016/j.jmapro.2021.09.011
Jianglong Gu, Ding J, Williams SW, Huimin Gu, Bai J, Zhai Y, Ma P (2016) The strengthening effect of inter-layer cold working and post-deposition heat treatment on the additively manufactured Al–6.3Cu alloy. Mater Sci Eng, A 651:18–26. https://doi.org/10.1016/j.msea.2015.10.101
Wang L, Xue J, Wang Q (2019) Correlation between arc mode, microstructure, and mechanical properties during wire arc additive manufacturing of 316L stainless steel. Mater Sci Eng, A 751:183–190. https://doi.org/10.1016/j.msea.2019.02.078
Suárez A, Panfilo A, Aldalur E, Veiga F, Gomez P (2022) Microstructure and mechanical properties of mild steel-stainless steel bimetallic components built using wire arc additive manufacturing. CIRP J Manuf Sci Technol 38:769–773. https://doi.org/10.1016/j.cirpj.2022.06.018
Dong B, Cai X, Lin S, Li X, Fan C, Yang C, Sun H (2020) Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: microstructures and mechanical properties. Addit Manuf 36. https://doi.org/10.1016/j.addma.2020.101447
Torbati-Sarraf H, Torbati-Sarraf SA, Chawla N, Poursaee A (2020) A comparative study of corrosion behavior of an additively manufactured Al-6061 RAM2 with extruded Al-6061 T6. Corros Sci 174. https://doi.org/10.1016/j.corsci.2020.108838
Fang X, Zhang L, Chen G, Huang K, Xue F, Wang L, Zhao J, Lu B (2021) Microstructure evolution of wire-arc additively manufactured 2319 aluminum alloy with interlayer hammering. Mater Sci Eng A 800. https://doi.org/10.1016/j.msea.2020.140168
Yang J, Wang Y, Li F, Huang W, Jing G, Wang Z, Zeng X (2019) Weldability, microstructure and mechanical properties of laser-welded selective laser melted 304 stainless steel joints. J Mater Sci Technol 35:1817–1824. https://doi.org/10.1016/j.jmst.2019.04.017
Ramalho A, Santos TG, Bevans B, Smoqi Z, Rao P, Oliveira JP (2022) Effect of contaminations on the acoustic emissions during wire and arc additive manufacturing of 316L stainless steel. Addit Manuf 51. https://doi.org/10.1016/j.addma.2021.102585
Nahmany M, Hadad Y, Aghion E, Stern A, Frage N (2019) Microstructural assessment and mechanical properties of electron beam welding of AlSi10Mg specimens fabricated by selective laser melting. J Mater Process Technol 270:228–240. https://doi.org/10.1016/j.jmatprotec.2019.02.025
Hanchen Yu, Li F, Yang J, Shao J, Wang Z, Zeng X (2018) Investigation on laser welding of selective laser melted Ti-6Al-4V parts: weldability, microstructure and mechanical properties. Mater Sci Eng, A 712:20–27. https://doi.org/10.1016/j.msea.2017.11.086
Wits WW, Jauregui Becker JM (2015) Laser beam welding of titanium additive manufactured parts. Procedia CIRP 28:70–75. https://doi.org/10.1016/j.procir.2015.04.013
Jing Han Yu, Shi GZ, Volodymyr K, Le W-Y (2022) Minimizing defects and controlling the morphology of laser welded aluminum alloys using power modulation-based laser beam oscillation. J Manuf Process 83:49–59. https://doi.org/10.1016/j.jmapro.2022.08.031
Cheng H, Zhou L, Sun J, Wen S, Wang Y, Chang B, Dong Du (2021) Processing modes in laser beam oscillating welding of Al6Cu alloy. J Manuf Process 68:1261–1270. https://doi.org/10.1016/j.jmapro.2021.06.049
He S, Liu L, Zhao Y, Kang Y, Wang F, Zhan X (2021) Comparative investigation between fiber laser and disk laser: microstructure feature of 2219 aluminum alloy welded joint using different laser power and welding speed. Optics Laser Technol 141. https://doi.org/10.1016/j.optlastec.2021.107121
Chen C, Yin X, Liao W, Xiang Y, Gao M, Zhang Yi (2021) Microstructure and properties of 6061/2A12 dissimilar aluminum alloy weld by laser oscillation scanning. J Market Res 14:2789–2798. https://doi.org/10.1016/j.jmrt.2021.08.105
Gao Z, Wang L, Wang Y, Lyu F, Zhan X (2022) Crack defects and formation mechanism of FeCoCrNi high entropy alloy coating on TC4 titanium alloy prepared by laser cladding. J Alloys Compd 903. https://doi.org/10.1016/j.jallcom.2022.163905
Chen S, Wu Y, Li Y, Chen M, Zheng Q, Zhan X (2020) Study on 2219 Al-Cu alloy T-joint used dual laser beam bilateral synchronous welding: parameters optimization based on the simulation of temperature field and residual stress. Optics Laser Technol 132. https://doi.org/10.1016/j.optlastec.2020.106481
Chen S, Zhao Y, Tian S, Yuanzhi Gu, Zhan X (2020) Study on keyhole coupling and melt flow dynamic behaviors simulation of 2219 aluminum alloy T-joint during the dual laser beam bilateral synchronous welding. J Manuf Process 60:200–212. https://doi.org/10.1016/j.jmapro.2020.10.063
Ahuja B, Karg M, Konstantin Yu, Nagulin MS (2014) Fabrication and characterization of high strength Al-Cu alloys processed using laser beam melting in metal powder bed. Phys Procedia 56:135–146. https://doi.org/10.1016/j.phpro.2014.08.156
Cao JY, Zhang CC, Xing YF, Wang M (2020) Pin plunging reinforced refill friction stir spot welding of Alclad 2219 to 7075 alloy. J Mater Process Technol 284. https://doi.org/10.1016/j.jmatprotec.2020.116760
Gu J, Gao M, Yang S, Bai J, Ding J, Fang X (2019) Pore formation and evolution in wire + arc additively manufactured 2319 Al alloy. Addit Manuf 30. https://doi.org/10.1016/j.addma.2019.100900
Chang T, Fang X, Liu G, Zhang H, Huang Ke (2022) Wire and arc additive manufacturing of dissimilar 2319 and 5B06 aluminum alloys. J Mater Sci Technol 124:65–75. https://doi.org/10.1016/j.jmst.2022.02.024
Ryan EM, Sabin TJ, Watts JF, Whiting MJ (2018) The influence of build parameters and wire batch on porosity of wire and arc additive manufactured aluminium alloy 2319. J Mater Process Technol 262:577–584. https://doi.org/10.1016/j.jmatprotec.2018.07.030
Zhan X, Zhang J, Wang J, Wang L, Li X, Zhao Y (2022) Microstructure characteristics and mechanical properties of fiber-diode hybrid laser welded 304 austenitic stainless steel. Mater Sci Eng: A 854. https://doi.org/10.1016/j.msea.2022.143884
Vishnukumar M, Pramod R, Kannan AR (2021) Wire arc additive manufacturing for repairing aluminium components in marine applications. Mater Lett 299. https://doi.org/10.1016/j.matlet.2021.130112
Cong B, Cai X, Qi Z, Qi B, Zhang Y, Zhang R, Guo W, Zhou Z, Yin Y, Bu X (2022) The effects of ultrasonic frequency pulsed arc on wire + arc additively manufactured high strength aluminum alloys. Addit Manuf 51. https://doi.org/10.1016/j.addma.2022.102617
Rajeshkumar R, Niranjani VL, Devakumaran K, Banerjee K (2021) Fusion boundary microstructure evolution and mechanical properties of cold metal transfer welded dissimilar A5754 and A5083 joint. Mater Lett 284. https://doi.org/10.1016/j.matlet.2020.128877
Chen L, Hu YN, He EG, Wu SC, Fu YN (2018) Microstructural and failure mechanism of laser welded 2A97 Al–Li alloys via synchrotron 3D tomography. Int J Light Mater Manuf 1:169–178. https://doi.org/10.1016/j.ijlmm.2018.08.001
Zhu H, Huang L, Li J, Li X, Ma H, Wang C, Ma F (2018) Strengthening mechanism in laser-welded 2219 aluminium alloy under the cooperative effects of aging treatment and pulsed electromagnetic loadings. Mater Sci Eng, A 714:124–139. https://doi.org/10.1016/j.msea.2017.12.081
Liu C, He J (2016) Numerical analysis of fluid transport phenomena and spiking defect formation during vacuum electron beam welding of 2219 aluminium alloy plate. Vacuum 132:70–81. https://doi.org/10.1016/j.vacuum.2016.07.033
Lyu F, Hu K, Wang L, Gao Z, Zhan X (2022) Regionalization of microstructure characteristics and mechanisms of slip transmission in oriented grains deposited by wire arc additive manufacturing. Mater Sci Eng: A 850. https://doi.org/10.1016/j.msea.2022.143529
Peng-liang NIU, Wen-ya LI, Yu-hua CHEN, Qi-peng LIU, Dao-lun CHEN (2022) Base material location dependence of corrosion response in friction-stir-welded dissimilar 2024-to-5083 aluminum alloy joints. Trans Nonferrous Metals Soc China 32:2164–2176. https://doi.org/10.1016/S1003-6326(22)65938-7
Jin P, Liu Y, Sun Q (2021) Evolution of crystallographic orientation, columnar to equiaxed transformation and mechanical properties realized by adding TiCps in wire and arc additive manufacturing 2219 aluminum alloy. Addit Manuf 39. https://doi.org/10.1016/j.addma.2021.101878
Fu R, Lu W, Guo Y, Lei H, Cui Y, Wang J, Gao D, Wang J, Liu C (2022) Achieving high strength-ductility of Al-Zn-Mg-Cu alloys via hot-wire arc additive manufacturing enabled by strengthening precipitates. Addit Manuf 58. https://doi.org/10.1016/j.addma.2022.103042
Zhang M, Fang X, Wang Y, Jiang X, Chang T, Xi N, Huang K (2022) High superelasticity NiTi fabricated by cold metal transfer based wire arc additive manufacturing. Mater Sci Eng: A 840. https://doi.org/10.1016/j.msea.2022.143001
Wang M, Chiu Y, Flahaut D, Jones IP, Zhang Z (2020) Secondary phase area fraction determination using SEM-EDS quantitative mapping. Mater Charact 167. https://doi.org/10.1016/j.matchar.2020.110506
Akgun E, Zhang X, Biswal R, Zhang Y, Doré M (2021) Fatigue of wire+arc additive manufactured Ti-6Al-4V in presence of process-induced porosity defects. Int J Fatigue 150. https://doi.org/10.1016/j.ijfatigue.2021.106315
Biswal R, Zhang X, Syed AK, Awd M, Ding J, Walther F, Williams S (2019) Criticality of porosity defects on the fatigue performance of wire + arc additive manufactured titanium alloy. Int J Fatigue 122:208–217. https://doi.org/10.1016/j.ijfatigue.2019.01.017
Xue C, Zhang Y, Mao P, Liu C, Guo Y, Qian F, Zhang C, Liu K, Zhang M, Tang S, Wang J (2021) Improving mechanical properties of wire arc additively manufactured AA2196 Al–Li alloy by controlling solidification defects. Addit Manuf 4https://doi.org/10.1016/j.addma.2021.102019
Tian S, Chen W, Chen S, Yuanzhi Gu, Gong X, Zhan X (2020) The effect of cryogenic applications on tensile strength of aluminum 2219–T87 T-joint welded by dual laser-beam bilateral synchronous welding. J Manuf Process 56:777–785. https://doi.org/10.1016/j.jmapro.2020.05.020
Funding
The authors acknowledge the financial support from the Natural Science Foundation of Jiangsu Province (BK20200431) and the Defense Industrial Technology Development Program (JCKY2020605C006).
Author information
Authors and Affiliations
Contributions
Provide funds and equipment, corresponding author: Leilei Wang; design and implementation of the experiments: Bowen Shi and Leilei Wang; experimental material preparation and processing: Xiaohong Zhan; microscopic observation and mechanical property testing: Bowen Shi and Leilei Wang; writing and image processing: Bowen Shi, Leilei Wang, and Feiyue Lyu; English instruction and grammar check: Zhuanni Gao and Huizi Shi; all authors have checked and approved that the final article is valid.
Corresponding author
Ethics declarations
Ethics approval
Not applicable.
Consent to participate
Not applicable.
Consent for publication
Not applicable.
Conflict of interest
The authors declare no competing interests.
Additional information
Publisher's note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Shi, B., Wang, L., Zhan, X. et al. Weld morphology, microstructure evolution, and mechanical properties of laser beam welding of wire arc additive manufactured Al-Cu substrate. Int J Adv Manuf Technol 127, 1935–1949 (2023). https://doi.org/10.1007/s00170-022-10340-x
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-022-10340-x