Abstract
Carbon fiber-reinforced plastic (CFRP) composites are increasingly utilized in the aircraft manufacturing field due to their excellent properties of high specific strength/modulus, good corrosion resistance, flexible designability, and long fatigue life. But CFRP composites belong to typical difficult-to-cut materials, and tearing, burrs, and delamination can easily occur in its drilling process. Longitudinal-torsional coupled ultrasonic-assisted drilling (LTC-UAD) is a promising technology to suppress the drilling defects of CFRP composites, and thrust force and torque are significant factors affecting the drilling quality of CFRP composites. In this paper, a mechanical model for predicting thrust force and torque in LTC-UAD of CFRP composites is presented in terms of the spindle speed, feed rate, ultrasonic parameters, tool geometry, and workpiece material properties. The oblique cutting modeling is used for the cutting lip, and the corresponding cutting region is divided into chipping region, pressing region, and bouncing region, respectively. The chisel edge is regarded as a rigid wedge-shaped body extruding into the workpiece material, and the contact theory is utilized to obtain the contact force between the chisel edge and the workpiece material. Furthermore, longitudinal and torsional vibrations are introduced into the modeling of cutting force by considering the dynamic feed angle and dynamic uncut chip thickness. The accuracy of the model is verified by the drilling experiments, and the results show that the predicted values of the thrust force and torque are in good consistency with the measured ones. The maximum deviations of the predicted thrust force and torque compared to the measured values are 13% and 11%, respectively.
Similar content being viewed by others
References
Njuguna J, Aumund-Kopp C, Friak M, Hehl AV, Berme B (2013) Structural materials and process in transportation. Wiley-VCH, Weinheim
Gaugel S, Sripathy P, Haeger A, Meinhard D, Bernthaler T, Lissek F, Kaufeld M, Knoblauch V, Schneider G (2016) A comparative study on tool wear and laminate damage in drilling of carbon-fiber reinforced polymers (CFRP). Compos. Struct 155:173–183. https://doi.org/10.1016/j.compstruct.2016.08.004
Zhang X, Chen Y, Xu J, Yang H, Chen Y (2020) Finite element simulation of and experimental study on three-dimensional drilling of large diameter carbon fiber composites. Diam. Abrasives Eng. 40(2):53–60. https://doi.org/10.13394/j.cnki.jgszz.2020.2.0010
An Q, Dang J, Li J, Wang C, Chen M (2020) Investigation on the cutting responses of CFRP/Ti stacks: with special emphasis on the effects of drilling sequences. Compos. Struct 253:1–13. https://doi.org/10.1016/j.compstruct.2020.112794
Wei Y, An Q, Ming W, Chen M (2016) Effect of drilling parameters and tool geometry on drilling performance in drilling carbon fiber–reinforced plastic/titanium alloy stacks. Adv Mech Eng 8(9):1–16. https://doi.org/10.1177/1687814016670281
Chen L, Zhang K, Cheng H, Qi Z, Meng Q (2017) A cutting force predicting model in orthogonal machining of unidirectional CFRP for entire range of fiber orientation. Int J Adv Manuf Technol 89:833–846. https://doi.org/10.1007/s00170-016-9059-5
Zhang L, Zhang H, Wang X (2006) A force prediction model for cutting unidirectional fibre-reinforced plastics. Mach Sci Technol 5(3):293–305. https://doi.org/10.1081/MST-100108616
Guo D, Wen Q, Gao H, Bao Y (2011) Prediction of the cutting forces generated in the drilling of carbon-fibre-reinforced plastic composites using a twist drill. Proc. IMechE Part B: J. Engineering Manufacture 226(1):28–42. https://doi.org/10.1177/0954405411419128
Anand RS, Patra K (2017) Mechanistic cutting force modelling for micro-drilling of CFRP composite laminates. CIRP J Manuf Sci Technol 16:55–63. https://doi.org/10.1016/j.cirpj.2016.07.002
Bai Y, Jia Z, Fu R, Hao J, Wang F (2021) Mechanical model for predicting thrust force with tool wear effects in drilling of unidirectional CFRP. Compos. Struct 262:1–10. https://doi.org/10.1016/j.compstruct.2021.113601
An Q, Chen J, Ming W, Chen M (2021) Machining of SiC ceramic matrix composites: A review. Chin. J. Aeronaut 34(4):540–567. https://doi.org/10.1016/j.cja.2020.08.001
Makhdum F, Phadnis VA, Roy A, Silberschmidt VV (2014) Effect of ultrasonically-assisted drilling on carbon fibre reinforced plastics. J Sound Vibr 333(23):5939–5952. https://doi.org/10.1016/j.jsv.2014.05.042
Sanda A, Arriola I, Navas VG, Bengoetxea I, Gonzalo O (2016) Ultrasonically assisted drilling of carbon fibre reinforced plastics and Ti6Al4V. J Manuf Process 22:169–176. https://doi.org/10.1016/j.jmapro.2016.03.003
Zhang L, Wang L, Liu X, Zhao H, Wang X, Luo H (2001) Mechanical model for predicting thrust and torque in vibration drilling fibre-reinforced composite materials. Int J Mach Tools Manuf 41(5):641–657. https://doi.org/10.1016/S0890-6955(00)00105-X
Geng D, Lu Z, Yao G, Liu J, Li Z, Zhang D (2017) Cutting temperature and resulting influence on machining performance in rotary ultrasonic elliptical machining of thick CFR. Int J Mach Tools Manuf 123:160–170. https://doi.org/10.1016/j.ijmachtools.2017.08.008
Liu J, Zhang D, Qin L, Yan L (2012) Feasibility study of the rotary ultrasonic elliptical machining of carbon fiber reinforced plastics (CFRP). Int J Mach Tools Manuf 53(1):141–150. https://doi.org/10.1016/j.ijmachtools.2011.10.007
Xu W, Zhang L (2014) On the mechanics and material removal mechanisms of vibration assisted cutting of unidirectional fibre-reinforced polymer composites. Int J Mach Tools Manuf 80–81:1–10. https://doi.org/10.1016/j.ijmachtools.2014.02.004
Wang J, Feng P, Zhang J, Guo P (2018) Reducing cutting force in rotary ultrasonic drilling of ceramic matrix composites with longitudinal-torsional coupled vibration. Manuf Let 18:1–5. https://doi.org/10.1016/j.mfglet.2018.08.002
Qiu X, Li P, Li C, Niu Q, Chen A, Ouyang P, Ko TJ (2018) Study on chisel edge drilling behavior and step drill structure on delamination in drilling CFRP. Compos Struct 203:404–413. https://doi.org/10.1016/j.compstruct.2018.07.007
Won MS, Dharan CKH (2002) Chisel edge and pilot hole effects in drilling composite laminates. J Manuf Sci Eng-Trans ASME 124(2):242–247. https://doi.org/10.1115/1.1448317
Zitoune R, Collombet F (2007) Numerical prediction of the thrust force responsible of delamination during the drilling of the long-fibre composite structures. Compos Pt A-Appl Sci Manuf 38(3):858–866. https://doi.org/10.1016/j.compositesa.2006.07.009
Langella A, Nele L, Maio A (2005) A torque and thrust prediction model for drilling of composite materials. Compos Pt A-Appl Sci Manuf 36(1):83–93. https://doi.org/10.1016/j.compositesa.2004.06.024
Meng Q, Zhang K, Cheng H, Liu S, Jiang S (2014) An analytical method for predicting the fluctuation of thrust force during drilling of unidirectional carbon fiber reinforced plastics. J Compos Mater 49:699–711. https://doi.org/10.1177/0021998314525483
Zhang H, Chen W, Chen D (2004) Study on cutting mechanical of carbon fiber reinforced plastics. Aeronautical manufacturing technology 7:57–59
Zhang H, Chen W, Chen D, Zhang L (2001) Assessment of the exit defects in carbon fibre-reinforced plastic plates caused by drilling. Key Eng Mater 196:43–52. https://doi.org/10.4028/www.scientific.net/KEM.196.43
Zhang L, Zhang H, Wang X (2001) A new mechanics model for predicting the forces of cutting unidirectional fibre-reinforced composites. Mach Sci Technol 5(3):293–305. https://doi.org/10.1081/MST-100108616
Wang D, Ramulu M, Arola D (1995) Orthogonal cutting mechanisms of graphite/epoxy composite. Part I: unidirectional laminate. Int J Mach Tools Manuf 35(12):1623–1638. https://doi.org/10.1016/0890-6955(95)00014-O
Elhachimi M, Torbaty S, Joyot P (1999) Mechanical modelling of high speed drilling. 1: predicting torque and thrust. Int J Mach Tools Manuf 39(4):553–568. https://doi.org/10.1016/S0890-6955(98)00050-9
Zhang L (2001) Solid Mechanics for Engineers. Macmillan Press, Basingstoke
Zhang L (2009) Cutting composites: a discussion on mechanics modelling. J Mater Process Technol 209(9):4548–4552. https://doi.org/10.1016/j.jmatprotec.2008.10.023
Fischer-Cripps AC (1999) The Hertzian contact surface. J Mater Sci 34:129–137. https://doi.org/10.1023/A:1004490230078
Wen Q (2013) Study of formation mechanism and evaluation method of C/E composites hole-making damages. Dalian University of Technology, Dissertation
Elhachimi M, Torbaty S, Joyot P (1999) Mechanical modelling of high speed drilling. 2: predicted and experimental results. Int J Mach Tools Manuf 39(4):569–581. https://doi.org/10.1016/S0890-6955(98)00051-0
Availability of data and material
The data used to support the findings of this study are available from the corresponding author on reasonable request.
Code availability
The corresponding code is made available on reasonable request.
Funding
National Key R&D Program of China (Grant No. 2019YFA0708902) and Fundamental Research Funds for the Central Universities (DUT20ZD102)
Author information
Authors and Affiliations
Contributions
Guofeng Ma contributed to the conceptualization, writing, and editing. Renke Kang contributed to the conception of the study. Chao Yan performed experiment verification. Yan Bao and Xianglong Zhu contributed to the methodology. Zhigang Dong contributed significantly to analysis and manuscript preparation. All authors read and approved the final manuscript.
Corresponding author
Ethics declarations
Ethics approval
Not applicable.
Consent to participate
Not applicable.
Consent for publication
Not applicable.
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Ma, G., Kang, R., Yan, C. et al. Mechanical model of thrust force and torque in longitudinal-torsional coupled ultrasonic-assisted drilling of CFRP. Int J Adv Manuf Technol 119, 189–202 (2022). https://doi.org/10.1007/s00170-021-08192-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-021-08192-y