Abstract
Ti-6Al-4V alloy machining is challenging due to inherent properties. Wiper inserts improve the surface finish at higher feed rates because of multi-radii geometry. Wiper inserts when combined with the cutting inserts can provide smooth surface finish. The current work is aimed to study the influence of cutting and wiper inserts in Ti-6Al-4V alloy milling while considering wear scar of tool/life, surface roughness, surface topography, micro-hardness, and microstructural evaluations as output responses under higher levels of feed rates in dry machining. The combination of cutting insert along with wiper geometry provides machining innovation due to the fact that good surface finish can be achieved in a single step. Three levels of feed rate (f) (1.2, 1.4, 1.6 mm/revolution) along with three levels of depth of cut (ap) (0.25, 0.40, 0.50 mm) were employed for the experimentation. The variation in workpiece surface roughness (Ra) was found in between 0.3 and 0.71 μm-Ra. Surface topography analysis under the scanning electron microscope (SEM) of the machined specimen revealed no voids/cracks; however, scratch marks/welding of microchips were noticed. No alteration in microstructure was found when milling at 1.2 and 1.4 mm/revolution feed rate. A white layer deepened to 18 μm from the milled surface was seen at a feed rate of 1.6 mm/revolution. In addition, approximately 15% increase in micro-hardness was observed beneath the milled surface when evaluated machining variables were at their peak levels, i.e., at 1.6 mm/revolution and 0.5 mm respectively, while only 5.4% increase in the said response was observed at f of 1.2 mm/revolution.
Similar content being viewed by others
Availability of data and materials
The data related to experimental findings is already reported within the paper, and it can also be available from the corresponding author Mudassar Rehman upon a reasonable request.
References
Gurrappa I (2003) Characterization of titanium alloy Ti-6Al-4V for chemical, marine and industrial applications. Mater Charact 51:131–139. https://doi.org/10.1016/j.matchar.2003.10.006
Khan SA, Ahmad MA, Saleem MQ, Ghulam Z, Qureshi MAM (2017) High-feed turning of AISI D2 tool steel using multi-radii tool inserts: tool life, material removed, and workpiece surface integrity evaluation. Mater Manuf Process 32:670–677. https://doi.org/10.1080/10426914.2016.1232815
Moussaoui K, Mousseigne M, Senatore J, Chieragatti R, Monies F (2013) Influence of milling on surface integrity of Ti6Al4V-study of the metallurgical characteristics: microstructure and microhardness. Int J Adv Manuf Technol 67:1477–1489. https://doi.org/10.1007/s00170-012-4582-5
Yang S, He C, Zheng M, Wan Q, Zhang Y (2018) Temperature field of tool engaged cutting zone for milling of titanium alloy with ball-end milling. Micromachines 9:672. https://doi.org/10.3390/mi9120672
Kiyak M, Sahin I, Cakir O (2016) Application of wiper insert in cutting tool technology. ICAS, pp 60-65
Pradhan S, Singh S, Prakash C, Królczyk G, Pramanik A, Pruncu CI (2019) Investigation of machining characteristics of hard-to-machine Ti-6Al-4V-ELI alloy for biomedical applications. J Mater Res Technol 8:4849–4862. https://doi.org/10.1016/j.jmrt.2019.08.033
Edkinsa KD, Van Rensburga NJ, Laubscher RF (2014) Evaluating the subsurface microstructure of machined Ti-6Al-4V. Procedia CIRP 13:270–275. https://doi.org/10.1016/j.procir.2014.04.046
Mhamdi M-B, Boujelbene M, Bayraktar E, Zghal A (2012) Surface integrity of titanium alloy Ti-6Al-4V in ball end milling. Phys Procedia 25:355–362. https://doi.org/10.1016/j.phpro.2012.03.096
Che-Haron CH, Jawaid A (2005) The effect of machining on surface integrity of titanium alloy Ti-6% Al-4% v. J Mater Process Technol 166:188–192. https://doi.org/10.1016/j.jmatprotec.2004.08.012
Lu M, Wang H, Liang G, Lin J, Yan G, Chen B, Zhao D (2018) Modeling and analysis of surface topography of Ti6Al4V alloy machining by elliptical vibration cutting. Int J Adv Manuf Technol 98:2759–2768. https://doi.org/10.1007/s00170-018-2452-5
Liang X, Liu Z (2018) Tool wear behaviors and corresponding machined surface topography during high-speed machining of Ti-6Al-4V with fine grain tools. Tribol Int 121:321–332. https://doi.org/10.1016/j.triboint.2018.01.057
Sun FJ, Qu SG, Pan YX, Li XQ, Li FL (2015) Effects of cutting parameters on dry machining Ti-6Al-4V alloy with ultra-hard tools. Int J Adv Manuf Technol 79:351–360. https://doi.org/10.1007/s00170-014-6717-3
Yang D, Liu Z (2015) Surface topography analysis and cutting parameters optimization for peripheral milling titanium alloy Ti-6Al-4V. Int J Refract Met Hard Mater 51:192–200. https://doi.org/10.1016/j.ijrmhm.2015.04.001
Wang T, Li Y, Liu J, Qin L, Wang N, Zhang L, Wang H, Li Z (2019) Milling force and surface topography of Ti-6Al-4V titanium alloy cladded by the laser. Surf Rev Lett 5:1850185. https://doi.org/10.1142/S0218625X18501858
Patil S, Jadhav S, Kekade S, Supare A, Powar A, Singh RKP (2016) The influence of cutting heat on the surface integrity during machining of titanium alloy Ti6Al4V. Procedia Manuf 5:857–869. https://doi.org/10.1016/j.promfg.2016.08.073
Wenjuan N, Bermingham M, Baburamani PS, Palanisamy S (2013) The effect of cutting speed and heat treatment on the fatigue life of Grade 5 and Grade 23 Ti-6Al-4V alloys. Mater Des 46:640–644. https://doi.org/10.1016/j.matdes.2012.10.056
Daymi A, Boujelbene Amara AB, Bayraktar E, Katundi D (2011) Surface integrity in high speed end milling of titanium alloy Ti-6Al-4V. Mater Sci Technol 27:387–394. https://doi.org/10.1179/026708310X12738371692932
Cellier A, Chalon F, Grimal-Perrigouas V, Bonhoure D, Leroy R (2014) Effects of cutting angles in Ti-6al-4v Milling process on surface integrity: influence of roughness and residual stresses on fatigue limit. Mach Sci Technol 18:565–584. https://doi.org/10.1080/10910344.2014.955369
Hashmi KH, Zakria G, Raza MB, Khalil S (2016) Optimization of process parameters for high speed machining of Ti-6Al-4V using response surface methodology. Int J Adv Manuf Technol 85:1847–1856. https://doi.org/10.1007/s00170-015-8057-3
Das B, Roy S, Rai RN, Saha SC (2016) Application of grey fuzzy logic for the optimization of CNC milling parameters for Al – 4 . 5 % Cu – TiC MMCs with multi-performance characteristics. Eng Sci Technol Int J 19:857–865. https://doi.org/10.1016/j.jestch.2015.12.002
Joshi S (2018) Dimensional inequalities in chip segments of titanium alloys. Eng Sci Technol Int J 21:238–244. https://doi.org/10.1016/j.jestch.2018.03.006
Groß K, Eifler M, Klauer K (2020) Determination of the surface topography of ball end micro milled material measures. Eng Sci Technol an Int J. https://doi.org/10.1016/j.jestch.2020.08.005
Saini S, Ahuja IS, Sharma VS (2012) Residual stresses, surface roughness, and tool wear in hard turning: a comprehensive review. Mater Manuf Process 27:583–598. https://doi.org/10.1080/10426914.2011.585505
Ferreira R, Carou D, Lauro CH, Davim JP (2016) Surface roughness investigation in the hard turning of steel using ceramic tools. Mater Manuf Process 31:648–652. https://doi.org/10.1080/10426914.2014.995051
Ehsan S, Khan SA, Mughal MP, Saleem MQ, Mufti NA (2019) Milling of Ti-6Al-4V alloy using hybrid geometry tooling. Int J Adv Manuf Technol 105:5045–5059. https://doi.org/10.1007/s00170-019-04613-1
Camel Cakir M, Ensarioglu C, Demirayak I (2009) Mathematical modeling of surface roughness for evaluating the effects of cutting parameters and coating material. J Mater Process Technol 209:102–109. https://doi.org/10.1016/j.jmatprotec.2008.01.050
Pramanik A, Littlefair G (2015) Machining of titanium alloy (Ti-6Al-4V)-theory to application. Mach Sci Technol 19:1–49. https://doi.org/10.1080/10910344.2014.991031
Masoudi S, Esfahani MJ, Jafarian F, Mirsoleimani SA (2019) Comparison the effect of MQL, wet and dry turning on surface topography, cylindricity tolerance and sustainability. Int J Precis Eng Manuf Green Technol. https://doi.org/10.1007/s40684-019-00042-3
Acknowledgements
The authors deeply acknowledge the University of Engineering and Technology, Lahore, Pakistan, for providing the research facilities via PhD studentship.
Funding
The current research work was financially supported by University of Engineering and Technology, Lahore, 54890, Pakistan, while its completion.
Author information
Authors and Affiliations
Contributions
Sana Ehsan: conceptualization, data analysis, resources, methodology, writing-original draft. Sarmad Ali Khan: supervision, resources, review and editing, data analysis and curation. Mudassar Rehman: data analysis and curation, investigation, review and editing.
Corresponding author
Ethics declarations
Ethics approval
The authors confirm that they have abided to the publication ethics and state that this work is original and has not been used for publication anywhere before.
Consent to participate
The authors are willing to participate in journal promotions and updates.
Consent for publication
The authors give consent to the journal regarding the publication of this work.
Competing interests
The authors declare no competing interests.
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Ehsan, S., Khan, S.A. & Rehman, M. Defect-free high-feed milling of Ti-6Al-4V alloy via a combination of cutting and wiper inserts. Int J Adv Manuf Technol 114, 641–653 (2021). https://doi.org/10.1007/s00170-021-06875-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-021-06875-0