Abstract
Demands for quality, complexity, and product integrity are crucial in the growing market of castings. Usually, the more complex is the manufacture of the casting, and the more difficult is to preserve the quality requirements. Additionally, casting manufacturing remains economically acceptable when the process scraps are limited in number. Welding repair can be adopted to eliminate some defectiveness due to the casting process although the effect of repairing on the mechanical performance of structural components has to be accounted. In this paper, a welding-repair procedure for cast aluminum samples, specifically designed to reproduce typical refurbishing of a complex full-scale cast frame, was implemented. A set of 14 weld-repaired aluminum samples was tested under fatigue loading condition, and the comparison with the unrepaired casts’ behavior is presented. The statistical analysis was performed by Maximum Likelihood Estimation (MLE) method. The repaired casts belonging the Class 1—Grade C assignment of the SAE Aerospace material specification (AMS 2175) show a slight lowering of the high cycle fatigue strength. However, in the higher stress regime, a reduction of the median fatigue life of the weld-repaired set was observed. Failure mechanisms of repaired cast samples were investigated and discussed.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Cole GS, Sherman AM (1995) Light weight materials for automotive applications. Mater Charact 35:3–9
Dahle AK, Lee YC, Nave MD, Schaffer PL, StJohn DH (2001) Development of the as-cast microstructure in magnesium–aluminium alloys. J Light Met 1:61–72
Ammar HR, Samuel AM, Samuel FH (2008) Effect of casting imperfections on the fatigue life of 319-F and A356-T6 Al-Si casting alloys. Mater Sci Eng A 473:65–75
Wang QG, Apelian D, Lados DA (2001) Fatigue behavior of A356-T6 aluminum cast alloys. Part I. Effect of casting defects. J Light Met 1:73–84
Borrego LP, Pires JTB, Costa JM, Ferreira JM (2007) Fatigue behaviour of laser repairing welded joints. Eng Fail Anal 14:1586–1593
Nascimento MP, Voorwald HJC (2010) Consideration about the welding repair effects on the structural integrity of an airframe critical to the flight-safety. Procedia Engineering 2:1895–1903
Sharples JK, Gardner L, Bate SK, Goldthorpe MR, Yates JR, Bainbridged H (2005) Project to evaluate the integrity of repaired welds. Int J Press Vessel Pip 82:319–338
Maddox SJ (2003) Review of fatigue assessment procedures for welded aluminium structures. Int J Fatigue 25:1359–1378
AMS2175 (2010) Aerospace material specification-Casting, Classification and inspection of, AMS 2175, SAE international
Weibull W (1951) A statistical distribution function of wide applicability. J Appl Mech 18:293–297
ASTM G166 (2011) Standard guide for statistical analysis of service life data, ASTM International
Esposito L, Gentile D, Bonora N (2007) Investigation on the Weibull parameters identification for local approach application in the ductile to brittle transition regime. Eng Fract Mech 74:549–562
Goglio L, Massimo R (2004) Comparison of fatigue data using maximum likelihood method. Eng Fract Mech 71:725–736
ASTM E739 (2010) Standard practice for statistical analysis of linear or linearized stress-life (S-N) and strain-life (ε-N) fatigue data, ASTM International
Nelson W (1984) Fitting of fatigue curves with nonconstant standard deviation to data with runouts. J Test Eval 12:69–77
Weibull W (1961) Fatigue testing and analysis of results. PERGAMON Press, London
Liard F (1983) Helicopter fatigue design guide, Advisory Group for Aerospace Research and Development, AGARD-AG-292
Veneziano L (2016) Unpublished master’s thesis, University of Naples “Federico II”, Italy
Marzio G, Yigng X, Russo R, Rosiello V (2018) Mixed mode fatigue crack propagation behaviour of aluminium F357 alloy. Eng Fail Anal 90:463–475
Li L, Liu Z, Snow M (2006) Effect of defects on fatigue strength of GTAW repaired cast aluminum alloy. Weld J 85:1–6
Linder J, Arvidsson A, Kron J (2006) The influence of porosity on the fatigue strength of high-pressure die cast aluminium. Fatigue Fract Eng Mater Struct 29:357–363
Mayer H, Papakyriacou M, Zettl B, Stanzl-Tschegg SE (2003) Influence of porosity on the fatigue limit of die cast magnesium and aluminium alloys. Int J Fatigue 25:245–256
Sonsino CM, Ziese J (1993) Fatigue strength and applications of cast aluminium alloys with different degrees of porosity. Int J Fatigue 15:75–84
Buffière JY, Savelli S, Jouneau PH, Maire E, Fougères R (2001) Experimental study of porosity and its relation to fatigue mechanisms of model Al-Si7-MgO.3 cast Al alloys. Mater Sci Eng A 316:115–126
Léopold G, Nadot Y, Billaudeau T, Mendez J (2015) Influence of artificial and casting defects on fatigue strength of moulded components in Ti-6Al-4V alloy. Fatigue Fract Eng Mater Struct 38:1026–1041
Apodaca DR, Louvier JG (1966) Static and fatigue properties of repair welded aluminum and magnesium premium quality casting. WESTEC conference, Los Angeles
Nordmark GE, Herbein WC, Dickerson PB, Montemarano TW (1987) Effect of weld discontinuities on fatigue of aluminium butt joints, 67th annual AWS meeting, Welding Research Supplement, Atlanta
Acknowledgments
The authors wish to thank Dr. Giovanni Pio Pucillo for the support to this work and the helicopters division of Leonardo S.p.A. that provided samples and foundry equipment.
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher’s note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Esposito, L., Bertocco, A., Cricrì, G. et al. Welding-repair effect on F357-T6 aluminum castings: analysis of fatigue life. Int J Adv Manuf Technol 102, 3699–3706 (2019). https://doi.org/10.1007/s00170-019-03436-4
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-019-03436-4