Abstract
Based on fluid mechanics and Preston equation, the influences of various technological parameters (including rotational speeds of workpieces, magnetic poles, and polishing disk and the machining gap) on polishing pressure on workpiece surfaces were investigated. On this basis, a material removal rate (MRR) model of cluster magnetorheological finishing (CMRF) with dynamic magnetic fields was established. Moreover, three pieces of single-crystal silicon substrates were subjected to synchronous polishing on the CMRF devices with dynamic magnetic fields in order to analyze the influence of different technological parameters on the MRR. It is showed that the theoretical simulation results favorably agree with the experimental results. The single-crystal silicon substrates with the initial surface roughness (Ra) of 0.48 μm were polished for 5 h on the optimal technological conditions: the machining gap and the eccentricity of magnetic poles are 0.9 mm and 6 mm, respectively; the workpieces are oscillated in Y direction for 40 mm at the oscillation speed of 600 mm/min; the rotational speeds of the polishing disk, magnetic poles, and workpieces are 50 r/min, 90 r/min, and 350 r/min, respectively. In this way, the super-smooth uniform surfaces with the roughness of Ra 2.4 nm were acquired.
Similar content being viewed by others
References
Kordonski W, Golini D (1999) Progress update in magnetorheological finishing. Int J Mod Phys B 13:2205–2212. https://doi.org/10.1142/S0217979299002320
Ghosh G, Mandal P, Mondal S (2017) Modeling and optimization of surface roughness in keyway milling using ANN, genetic algorithm, and particle swarm optimization. Int J Adv Manuf Technol 2:1–20. https://doi.org/10.1007/s00170-017-1417-4
Wang Y, Zhang Y, Feng Z (2016) Analyzing and improving surface texture by dual-rotation magnetorheological finishing. Appl Surf Sci 360:224–233. https://doi.org/10.1016/j.apsusc.2015.11.009
Sato T, Wu Y, Lin W et al (2009) Study on magnetic compound fluid (MCF) polishing process using fluctuating magnetic field(flow behaviour and applications of complex fluids characterized by non-Newtonian viscosity or functionality). Trans Jpn Soc Mech Eng B 75:1007–1012. https://doi.org/10.1299/kikaib.75.753_1007
Sidpara A, Jain V (2012) Nanofinishing of freeform surfaces of prosthetic knee joint implant. Proc Inst Mech Eng B J Eng Manuf 226:1833–1846. https://doi.org/10.1177/0954405412460452
Sidpara A, Jain V (2012) Nano–level finishing of single crystal silicon blank using magnetorheological finishing process. Tribol Int 47:159–166. https://doi.org/10.1016/j.triboint.2011.10.008
Singh A, Jha S, Pandey P (2012) Nanofinishing of a typical 3D ferromagnetic workpiece using ball end magnetorheological finishing process. Int J Mach Tools Manuf 63:21–31. https://doi.org/10.1016/j.ijmachtools.2012.07.002
Singh A, Jha S, Pandey P (2013) Mechanism of material removal in ball end magnetorheological finishing process. Wear 302:1180–1191. https://doi.org/10.1016/j.wear.2012.11.082
Yan Q, Yan J, Lu J (2010) Ultra smooth planarization polishing technique based on the cluster magnetorheological effect. Adv Mater Res 135:18–23. https://doi.org/10.4028/www.scientific.net/AMR.135.18
Pan J, Yan Q, Jiabin L (2014) Cluster magnetorheological effect plane polishing technology. J Mech Eng 50:205. https://doi.org/10.3901/JME.2014.01.205
Pan J, Yu P, Yan Q (2017) An experimental analysis of strontium titanate ceramic substrates polished by magnetorheological finishing with dynamic magnetic fields formed by rotating magnetic poles. Smart Mater Struct 26:055017. https://doi.org/10.1088/1361-665X/aa67cf
Yu P, Pan J, Yan Q (2016) Magnetorheological finishing with tangential magnetic fields formed by the rotation of a magnetic pole. Int J Adv Abras Technol 7:307. https://doi.org/10.1504/IJAT.2016.081349
Kordonski W, Jacobs S (1996) Model of magnetorheological finishing. J Intell Mater Syst Struct 7:131–137. https://doi.org/10.1177/1045389X9600700202
Kordonski W, Gorodkin S (2011) Material removal in magnetorheological finishing of optics. Appl Opt 50:1984–1994. https://doi.org/10.1364/AO.50.001984
Shorey A, Gregg L, Romanofsky H (1999) Study of material removal during magnetorheological finishing. Proc SPIE Int Soc Opt Eng 3782. https://doi.org/10.1117/12.369176
Jha S, Jain V (2009) Rheological characterization of magnetorheological polishing fluid for MRAFF. Int J Adv Manuf Technol 42:656–668. https://doi.org/10.1007/s00170-008-1637-8
Miao C, Shafrir S, Lambropoulos J (2009) Shear stress in magnetorheological finishing for glasses. Appl Opt 48:2585–2594. https://doi.org/10.1364/AO.48.002585
Zhang F, Zhang X, Yu J, Wang Q, Guo P (2000) Foundation of mathematics model of magnetorheological finishing. Opt Technol 26:190–192. https://doi.org/10.13741/j.cnki.11-1879/o4.2000.02.032
Pan J, Yan Q (2015) Material removal mechanism of cluster magnetorheological effect in plane polishing. Int J Adv Manuf Technol 81:2017–2026. https://doi.org/10.1007/s00170-015-7332-7
Pan J, Yan Q, Gao W, Yu P. (2018) A self-sharpening polishing device with magnetorheological flexible polishing pad formed by dynamic magnetic field and polishing method thereof. Patent, US20180021910A1
Sato T, Wu Y, Lin W, Shimada K (2009) Study of three-dimensional polishing using magnetic compound fluid (MCF). Adv Mater Res 76-78:288–293. https://doi.org/10.4028/www.scientific.net/AMR.76-78.288
Bai Z, Yan Q, Xu X (2015) Experimental investigations into forces acting between cluster MR effect pad and workpiece surface. Chin J Mech Eng 59:190–197. https://doi.org/10.3901/JME.2015.15.190
Tao R (2001) Super-strong magnetorheological fluids. J Phys Condens Matter 13:979–R999. https://doi.org/10.1088/0953-8984/13/50/202
Degroote J, Marino A, Wilson J (2007) Removal rate model for magnetorheological finishing of glass. Appl Opt 46:7927–7941. https://doi.org/10.1364/AO.46.007927
Xiang W, Ling F (2013) Review of coupled research for mechanical dynamics and fluid mechanics of reciprocating compressor. Appl Mech Mater 327:227–232. https://doi.org/10.4028/www.scientific.net/AMM.327.227
Ranjan P (2014) Modelling and simulation of chemo-mechanical magnetorheological finishing (CMMRF) process. Int J Precis Technol 4:230. https://doi.org/10.1504/IJPTECH.2014.067743
Bachovchin K, Hoburg J, Post R (2012) Magnetic fields and forces in permanent magnet levitated bearings. IEEE Trans Magn 48:2112–2120. https://doi.org/10.1109/TMAG.2012.2188140
Acknowledgements
The authors wish to gratefully acknowledge the help of Dr. Xiaowei Zhang, a visiting fellow of Nagoya University in the final language editing of this paper.
Funding
This study received funding from the Guangdong Provincial Science and Technology Project (No. 2016A010102014) and the Guangdong Province Natural Science Foundation Project (No. 2015A030311044).
Author information
Authors and Affiliations
Corresponding authors
Rights and permissions
About this article
Cite this article
Pan, J., Guo, M., Yan, Q. et al. Research on material removal model and processing parameters of cluster magnetorheological finishing with dynamic magnetic fields. Int J Adv Manuf Technol 100, 2283–2297 (2019). https://doi.org/10.1007/s00170-018-2747-6
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-2747-6