Abstract
Fixture layout has a direct impact on the machining quality of thin-walled parts. However, there are few studies on the flexible fixture of automotive interior decoration, especially for car dashboards. With the development of individualized demand, the production trend of car dashboards is changing from large-quantity to multi-variety and small-batch, which makes the demand for flexible fixture of car dashboards. Therefore, a kind of flexible fixture for car dashboards based on a new N-M principle was proposed in this paper. With the scientific problem illustrated, this paper put forward a method by coupling genetic algorithm and finite element analysis to deal with the flexible fixture layout optimization. The optimization model of fixture layout based on the N-M principle was set up by taking the maximum deformation of car dashboards as the optimization objective and setting constraints. Finite element model was established to calculate the deformation by setting the boundary conditions, the equivalent cutting force. Genetic algorithm was used to search the optimal solution of the fixture layout. A case was studied to verify the method, and the result showed that the maximum deformation was reduced by 56.5% and the stiffness was increased by 0.77 times, which fully demonstrated the effectiveness of the method.
Similar content being viewed by others
References
Liao YG (2016) Non-linear and explicit finite element analysis in dynamic responses of handling sheet-metal parts. Proc Inst Mech Eng B J Eng Manuf 221(6):1021–1030. https://doi.org/10.1243/09544054jem768
Qian X, Yang L, Lou P (2015) The autonomous detection of sheet metal parts using image processing. Int J Adv Manuf Technol 85(1–4):469–479. https://doi.org/10.1007/s00170-015-7946-9
Jie L, Jianhua M, Shuhuai H (2004) Sheet metal dieless forming and its tool path generation based on STL files. Int J Adv Manuf Technol 23:696–699. https://doi.org/10.1007/s00170-003-1783-y
Wu H, Lu B, Guo C, Wang Y (2014) Impact analysis of geometric characteristics and boundary conditions on the stiffness of sheet metal parts. Mater Sci 20. https://doi.org/10.5755/j01.ms.20.4.5955
Dietrich L, Socha G, Kowalewski ZL (2014) Anti-buckling fixture for large deformation tension-compression cyclic loading of thin metal sheets. Strain 50:174–183. https://doi.org/10.1111/str.12078
Zhang Q, Liu Y, Zhang Z (2015) A new optimization method for sheet metal forming processes based on an iterative learning control model. Int J Adv Manuf Technol 85(5–8):1063–1075. https://doi.org/10.1007/s00170-015-7975-4
Cai W, Hu SJ, Yuan JX (1996) Deformable sheet metal fixturing: principles, algorithms, and simulations. J Manuf Sci Eng 118:318. https://doi.org/10.1115/1.2831031
Xiong L, Molfino R, Zoppi M (2013) Fixture layout optimization for flexible aerospace parts based on self-reconfigurable swarm intelligent fixture system. Int J Adv Manuf Technol 66:1305–1313. https://doi.org/10.1007/s00170-012-4408-5
Wang Y, Chen X, Gindy N, Xie J (2006) Elastic deformation of a fixture and turbine blades system based on finite element analysis. Int J Adv Manuf Technol 36(3–4):296–304. https://doi.org/10.1007/s00170-006-0841-7
Siebenaler SP Melkote SN (2006) Prediction of workpiece deformation in a fixture system using the finite element method. Int J Mach Tools Manuf 46:51–58. https://doi.org/10.1016/j.ijmachtools.2005.04.007
Ratchev S, Phuah K, Liu S (2007) FEA-based methodology for the prediction of part–fixture behaviour and its applications. J Mater Process Technol 191:260–264. https://doi.org/10.1016/j.jmatprotec.2007.03.020
Ni J, Tang WC, Xing Y (2016) Performance of reducing the dimensional error of an assembly by the rivet upsetting direction optimization. Proc Inst Mech Eng B J Eng Manuf 231:2133–2144. https://doi.org/10.1177/0954405415625918
Ni J, Tang WC, Xing Y, Xing Y, Ben KC, Li M (2016) A local-to-global dimensional error calculation framework for the riveted assembly using finite-element analysis. J Manuf Sci Eng 138:031004. https://doi.org/10.1115/1.4031101
Huang X, Sun J, Li J (2014) Finite element simulation and experimental investigation on the residual stress-related monolithic component deformation. Int J Adv Manuf Technol 77(5–8):1035–1041. https://doi.org/10.1007/s00170-014-6533-9
Kim DM, Bajpai V, Kim BH, Park HW (2015) Finite element modeling of hard turning process via a micro-textured tool. Int J Adv Manuf Technol 78(9–12):1393–1405. https://doi.org/10.1007/s00170-014-6747-x
Lu C, Zhao HW (2014) Fixture layout optimization for deformable sheet metal workpiece. Int J Adv Manuf Technol 78:85–98. https://doi.org/10.1007/s00170-014-6647-0
Kulankare KK, Melkote SN (2000) Machining fixture layout optimization using the genetic algorithm. Int J Mach Tools Manuf 40:579–598. https://doi.org/10.1016/S0890-6955(99)00072-3
Vallapuzha S, Meter ECD, Choudhuri S, Khetan RP (2002) An investigation of the effectiveness of fixture layout optimization methods. Int J Mach Tools Manuf 42:251–263. https://doi.org/10.1016/S0890-6955(01)00114-6
Prabhaharan G, Padmanaban KP, Krishnakumar R (2006) Machining fixture layout optimization using FEM and evolutionary techniques. Int J Adv Manuf Technol 32:1090–1103. https://doi.org/10.1007/s00170-006-0441-6
Padmanaban KP, Arulshri KP, Prabhakaran G (2009) Machining fixture layout design using ant colony algorithm based continuous optimization method. Int J Adv Manuf Technol 45:922–934. https://doi.org/10.1007/s00170-009-2035-6
Kaya N (2006) Machining fixture locating and clamping position optimization using genetic algorithms. Comput Ind 57:112–120. https://doi.org/10.1016/j.compind.2005.05.001
Kulankara K, Satyanarayana S, Melkote SN (2002) Iterative fixture layout and clamping force optimization using the genetic algorithm. J Manuf Sci E: T ASME 124:119–125. https://doi.org/10.1115/1.1414127
Chen W, Ni L, Xue J (2007) Deformation control through fixture layout design and clamping force optimization. Int J Adv Manuf Technol 38:860–867. https://doi.org/10.1007/s00170-007-1153-2.
Liu Z-H, Wang MY, Wang KD, Mei XC (2013) Fixture performance improvement by an accelerated integral method of fixture layout and clamping force plan. Proc Inst Mech Eng B J Eng Manuf 227:1819–1829. https://doi.org/10.1177/0954405413494194
Abedini V, Shakeri M, Siahmargouei MH, Baseri H (2014) Analysis of the influence of machining fixture layout on the workpiece’s dimensional accuracy using genetic algorithm. Proc Inst Mech Eng B J Eng Manuf 228:1409–1418. https://doi.org/10.1177/0954405413519605
Rex FMT, Ravindran D (2015) An integrated approach for optimal fixture layout design. Proc Inst Mech Eng B J Eng Manuf 231:1217–1228. https://doi.org/10.1177/0954405415590991
Xin J, Dou J, Zhu L, Wang X, Wang L, Wang Z (2010) Machining fixture layout optimization using particle swarm optimization algorithm. 7997: 79970S. https://doi.org/10.1117/12.885289.
Xing Y, Wang Y (2012) Fixture layout design based on two-stage method for sheet metal components. Proc Inst Mech Eng B J Eng Manuf 227:162–172. https://doi.org/10.1177/0954405412463132
Liu P, Li Y, Zhang K-F, Cheng H (2012) Based on region division setup planning for sheet metal assembly in aviation industry. Proc Inst Mech Eng B J Eng Manuf 227:153–161. https://doi.org/10.1177/0954405412462656.
Yang B, Wang Z, Yang Y, Kang Y, Li C (2017) Optimization of fixture locating layout for sheet metal part by cuckoo search algorithm combined with finite element analysis. Adv Mech Eng 9:168781401770483. https://doi.org/10.1177/1687814017704836
Cheng H, Li Y, Zhang KF, Luan C, Xu YW, Li MH (2012) Optimization method of fixture layout for aeronautical thin-walled structures with automated riveting. Assem Autom 32:323–332. https://doi.org/10.1108/01445151211262384
Wang Z, Yang Y, Yang B, Kang Y (2016) Optimal sheet metal fixture locating layout by combining radial basis function neural network and bat algorithm. Adv Mech Eng 8:168781401668190. https://doi.org/10.1177/1687814016681905
Author information
Authors and Affiliations
Corresponding author
Ethics declarations
Conflict of interest
The authors declare that they have no conflicts of interest.
Rights and permissions
About this article
Cite this article
Chen, C., Sun, Y. & Ni, J. Optimization of flexible fixture layout using N-M principle. Int J Adv Manuf Technol 96, 4303–4311 (2018). https://doi.org/10.1007/s00170-018-1907-z
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-018-1907-z