Abstract
Metal Matrix Composites (MMCs) are a class of materials combining two dissimilar materials (e.g., metal & ceramic) that when combined, provide unique properties including low density, high specific strength, high specific modulus, high thermal conductivity, and wear resistance and can be used in range of applications including high-temperature applications, structural applications, and can act as crack arrestors in fatigue applications. However, MMCs are not widely adopted due to their high cost and are limited in the geometrical configuration of the ceramic cores (e.g., extrusion, tiles, stochastic foams, etc.). In this work, the authors proposed a novel process protocol that takes advantage of the geometrical freedom offered by Additive Manufacturing (AM). Specifically, the authors look to print a complex ceramic structure from precursor powders via Binder Jetting AM technology to incorporate into a bonded sand mold and the subsequently casted metal matrix. The manufacturing process for creating a successful MMC is divided into two distinct steps: i) determination of the printing parameters, pre-and-post sintering ceramic characterization, and ii) molding, casting, and testing MMCs. Through sintering experiments, a sintering temperature of 1375 ∘C was established for the ceramic insert (70 % cordierite). Upon printing and sintering the ceramic, three-point bend tests showed the MMCs had less strength than the matrix material likely due post-processing and geometrical effects, effects of gravity casting, and relatively high porosity developed in the body. It was found that the ceramic metal interface had minimal mechanical interlocking and chemical bonding limiting the strength of the final MMCs. Furthermore, the authors provide directions for future work on how to successfully utilize the proposed manufacturing process to create printed MMCs with more effective properties.
Similar content being viewed by others
References
3D Systems (2012) Solutions: Metal Casting. http://www.zcorp.com/en/Solutions/Castings-Patterns-Molds/spage.aspx
Agarwala MK, Weeren RV, Vaidyanathan R, Langrana N, Safari A, Garofalini SH, Danforth SC (1990) Structural ceramics by fused deposition of ceramics. In: International Solid Freeform Fabrication Symposium, Austin, TX
ASTM Standard B962-14 (2014) Standard Test Methods for Density of Compacted or Sintered Powder Metallurgy (PM) Products Using Archimedes’ Principle
Bedard RL, Flanigen EM (1990) High Density Cordierite Ceramics from Zeolite
Boudchicha MR, Achour S, Harabi A (2001) Crystallization and sintering of cordierite and anorthite based. J Mater Sci Lett 20:215–217
Chawla N, Chawla KK (2005) Metal matrix composites. Springer Science+Business Media
Cima MJ, Haggerty JS, Sachs EM, Williams PA (1993) Three-dimensional printing techniques. http://www.google.com/patents/US5204055
Clyne TW, Withers PJ (1993) An Introduction to Metal Matrix Composites. Cambridge University Press,
Deshpande VS, Fleck NA, Ashby MF (2001) Effective properties of the octet-truss lattice material. J Mech Phys Solids 49:1747–1769
Ellingham HJT (1944) Reducibility of oxides and sulphides in metallurgical processes. J Soc Chem Indust 63 (10):289–320. doi:10.1002/jctb.5000631001
ExOne (2014) ExOne: Digital Part Materialization. http://www.exone.com/materialization/what-is-digital-part-materialization/sand
Gibson I, Rosen DW, Stucker B (2010) Additive Manufacturing Technologies
Griffith ML, Halloran JW (1996) Freeform fabrication of ceramics via stereolithography. J Am Ceram Soc 79(10):2601–2608
Günay E (2011) Sintering behavior and properties of sepiolite-based cordierite 35:83–92. doi:10.3906/muh-1008-14
Kainer KU (2006) Metal matrix composites: Custom-made materials for automotive and aerospace engineering. Wiley,
Lakshminarayan U, Ogrydiziak S, Marcus HL (1990) Selective Laser Sintering of Ceramic Materials. In: International Solid Freeform Fabrication Symposium, Austin, TX, pp 16–26
Moon J, Caballero AC, Hozer L, Chiang YM, Cima MJ (2001) Fabrication of functionally graded reaction infiltrated SiC–Si composite by three-dimensional printing (3DP™) process. Mater Sci Eng: A 298(1-2):110–119. doi:10.1016/S0921-5093(00)01282-X
Naplocha K, Janus A, Kaczmar J, Samsonowicz Z (2000) Technology and mechanical properties of ceramic preforms for composite materials. J Mater Process Technol 106(1-3):119–122. doi:10.1016/S0924-0136(00)00601-4
Ogiwara T, Noda Y, Shoji K, Kimura O (2010) Solid state synthesis and its characterization of high density cordierite ceramics using fine oxide powders. J Ceram Soc Jpn 118(1375):246–249. doi:10.2109/jcersj2.118.246
Rahaman MN (2003) Ceramic processing and sintering, 2nd edn. Marcel Dekker, Inc,
Rambo CR, Travitzky N, Zimmermann K, Greil P (2005) Synthesis of TiC/Ti-Cu composites by pressureless reactive infiltration of TiCu alloy into carbon preforms fabricated by 3D-printing. Mater Lett 59 (8-9):1028–1031
Sachs E, Cima M, Cornie J, Brancazio D, Bredt J, Curodeau A, Esterman M, Fan T, Harris C, Kremmin K, Lee SJ, Pruitt B, Williams P (1990) Dimensional printing : Rapid tooling and prototypes directly from CAD representation. In: International Solid Freeform Fabrication Symposium, Austin, TX, pp 27–47
Sachs E, Cima M, Cornie J, Brancazio D, Bredt J, Curodeau A, Fan T, Khanuja S, Lauder A, Lee J, Michaels S (1993) Three-dimensional printing: The physics and implications of additive manufacturing. CIRP Ann - Manuf Technol 42(1):257–260
Schleg FP (2003) Technology of metalcasting american foundry society, Schaumburg, IL
Seitz H, Rieder W, Irsen S, Leukers B, Tille C (2005) Three-dimensional printing of porous ceramic scaffolds for bone tissue engineering. J biomed Mater Res Part B, Appl Biomater 74(2):782–8. doi:10.1002/jbm.b.30291
Snelling DA, Kay R, Druschitz A, Williams CB (2012) Mitigating gas defects in castings produced from 3d printed molds. In: 117th Metalcasting Congress
Sōmiya S, Aldinger F, Claussen N, Spriggs RM, Uchino K, Koumoto K, Kaneno M (2003) Handbook of advanced ceramics. Elsevier Inc,
Standke G, Müller T, Neubrand A, Weise J, Göpfert M (2010) Cost-efficient metal-ceramic composites-novel foam-preforms, casting processes and characterisation. Adv Eng Mater 12(3):189–196. doi:10.1002/adem.200900285
Suresh S, Mortensen A, Needleman A (1993) Fundamentals of metal-matrix composites. Butterworth-Heinemann, Boston
Utela B, Storti D, Anderson R, Ganter M (2008) A review of process development steps for new material systems in three dimensional printing (3DP). J Manuf Process 10(2):96–104. doi:10.1016/j.jmapro.2009.03.002
Vaucher S, Empa OB (2001) Bonding and interface formation in Metal Matrix Composites MMC - Assess Thematic Network
Yoo J, Cima MJ, Khanuja S, Sachs EM (1993) Structural ceramic components by 3D printing. In: International Solid Freeform Fabrication Symposium, Austin, TX, pp 40–50
Yoo J, Cima MJ, Suresh S (1995) Fabrication and microstructural control of advanced ceramic components by three dimensional printing. Ceram Eng Sci Proc 16(5):755–762
Zhang W, Melcher R, Travitzky N, Bordia RK, Greil P (2009) Three-dimensional printing of complex shaped alumina/glass composites. Adv Eng Mater 11(12):1039–1043
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Snelling, D.A., Williams, C.B., Suchicital, C.T.A. et al. Binder jetting advanced ceramics for metal-ceramic composite structures. Int J Adv Manuf Technol 92, 531–545 (2017). https://doi.org/10.1007/s00170-017-0139-y
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-017-0139-y