Skip to main content
SpringerLink
Log in

An analytical model of grinding force based on time-varying dynamic behavior

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

This paper presents a time-domain force analytical model of cylindrical grinding process, which focuses on the time-varying dynamic behaviors caused by unstable machining process. This model analyzes the dynamic behaviors between the wheel and workpiece as the contact length and the maximum undeformed chip thickness change. It contains the grinding force affected by spindle run-out and vibration and especially focuses on the variation of grinding force which is affected by grinding parameters. In order to ensure the accuracy and computational efficiency of this model, the on-line detection results of grinding process have been adopted into the force analytical model. Through this model, explanations of different grinding parameter combinations are provided for grinding mechanism observed from the simulated results. Therefore, this model is validated by comparing the simulated results with the experimental results.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Hwang TW, Evans CJ, Malkin S (2000) An investigation of high speed grinding with electroplated diamond wheels. CIRP Ann Manuf Technol 49(1):245–248

    Article  Google Scholar 

  2. Jackson MJ, Davis CJ, Hitchiner MP, Mills B (2001) High speed grinding with CBN grinding wheels—applications and future technology. J Mater Process Technol 110(1):78–88

    Article  Google Scholar 

  3. Ha MK, Kwak JS, Hwang YM, Chung JS (2004) Machining characteristics of mold material in high-speed grinding. J Mater Process Technol 155:1189–1195

    Article  Google Scholar 

  4. Schulz H, Moriwaki T (1992) High-speed machining. CIRP Ann Manuf Technol 41(2):637–643

  5. Kopac J, Krajnik P (2006) High-performance grinding—a review. J Mater Process Tech 175:278–284

    Article  Google Scholar 

  6. Jackson MJ, Davis CJ, Hitchiner MP, Mills B (2001) High-speed grinding with CBN grinding wheels Ð applications and future technology. J Mater Process Tech 110:78–88

    Article  Google Scholar 

  7. Li B, Ni J, Yang J, Liang SY (2014) Study on high-speed grinding mechanisms for quality and process efficiency. Int J Adv Manuf Technol 70(5):813–819

    Article  Google Scholar 

  8. Wan M, Ma YC, Wei JZ, Zhang H (2016) Study of static and dynamic ploughing mechanisms by establishing generalized model with static milling forces. Int J Mech Sci 114:120–131

    Article  Google Scholar 

  9. Wan M, Altintas Y (2014) Mechanics and dynamics of thread milling process. Int J Mach Tool Manu 87:16–26

    Article  Google Scholar 

  10. Wan M, Kilic ZM, Altintas Y (2015) Mechanics and dynamics of multi-functional tools. Trans ASME J Manuf Sci Eng 137(1):011019

    Article  Google Scholar 

  11. Wan M, Ma YC, Wei JZ, Yang Y (2015) Study on the construction mechanism of stability lobes in milling process with multiple modes. Int J Adv Manuf Technol 79:589–603

    Article  Google Scholar 

  12. Lin T, Huang H, Ramesh K, Huang T (2005) High speed versus conventional grinding in high removal rate machining of alumina and alumina–titania. Mach Tools Manuf 45:897–907

    Article  Google Scholar 

  13. Guo MX, Li BZ, Ding ZS, Liang S (2016) Empirical modeling of dynamic grinding force based on process analysis. Int J Adv Manuf Technol 1–11

  14. Jiang JL, Ge PQ, Bi WB, Zhang L, Wang DX (2013) 2D/3D ground surface topography modeling considering dressing and wear effects in grinding process. Int J Mach Tool Manu 74(74):29–40

    Article  Google Scholar 

  15. Inasaki I, Karpuschewski B, Lee HS (2001) Grinding chatter-origin and suppression. CIRP Ann Manuf Technol 50(2):515–534

    Article  Google Scholar 

  16. Altintas Y, Weck M (2004) Chatter stability of metal cutting and grinding. CIRP Ann Manuf Technol 53(2):619–652

    Article  Google Scholar 

  17. Hahn RS (1954) On the theory of regenerative chatter in precision-grinding operations. Trans ASME 76(1):593–597

    Google Scholar 

  18. Thompson RA (1977) On the doubly regenerative stability of a grinder: the combined effect of wheel and workpiece speed. ASME J Eng Ind 99:237–241

    Article  Google Scholar 

  19. Rowe WB (2009) Principles of modern grinding technology. William Andrew Press, Norwich

    Google Scholar 

  20. Thompson RA (1986) On the doubly regenerative stability of a grinder: the theory of chatter growth. ASME J Eng Ind 108:75–82

    Article  Google Scholar 

  21. Thompson RA (1992) On the doubly regenerative stability of a grinder: the effect of contact stiffness and wave filtering. ASME J Eng Ind 114:53–60

    Google Scholar 

  22. Shimizu J, Zhou LB, Eda H (2002) Simulation and experimental analysis of super high-speed grinding of ductile material. J Mater Process Technol 129:19–24

    Article  Google Scholar 

  23. Leonesio M, Parenti P, Cassinari A et al (2012) A time-domain surface grinding model for dynamic simulation. Procedia CIRP 4:166–171

    Article  Google Scholar 

  24. Thompson RA (1977) On the doubly regenerative stability of a grinder: the combined effect of wheel and workpiece speed. J Eng Ind 99(1):237–241

    Article  Google Scholar 

  25. Li HQ, Yun CS (2005) A time-domain dynamic model for chatter prediction of cylindrical plungle grinding processes. J Manuf Sci E-T ASME 128(2):404–415

    Article  Google Scholar 

  26. Li HQ, Yun CS (2007) A study on chatter boundaries of cylindrical plungle grinding with process condition-dependent dynamics. Int J Mach Tool Manu 47:1563–1572

    Article  Google Scholar 

  27. Nakajima T, Yoshikawa M, Tsukamoto S, Takehara K (1998) Simulation of ground surface profile generation with measured distribution of mounting spring constant, dimensional position and shape of abrasive grains. Jap Soc Precision Eng 64(7):1072–1077

    Article  Google Scholar 

  28. Verkerk J, Pekelharing AJ (1975) The real contact length in cylindrical plunge grinding. CIRP Annal 24(1):259–264

    Google Scholar 

  29. Malkin S, Guo C (1989) Grinding technology: theory and applications of machining with abrasives[M]. Industrial Press Inc, USA

    Google Scholar 

  30. Choi T, Shin YC (2007) Generalized intelligent grinding advisory system. Int J ProdRes 45(8):1899–1932

    Article  MATH  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Mechanical Engineering School, Donghua University, Shanghai, 201620, China

    Yinchen ma, Jianguo yang, Beizhi li & Jun lu

Authors
  1. Yinchen ma
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Jianguo yang
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Beizhi li
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Jun lu
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Yinchen ma.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

ma, Y., yang, J., li, B. et al. An analytical model of grinding force based on time-varying dynamic behavior. Int J Adv Manuf Technol 89, 2883–2891 (2017). https://doi.org/10.1007/s00170-016-9751-5

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-016-9751-5

Keywords

Search

Navigation