Abstract
Two types of polyurethane (PU) foam-filled energy absorption connectors were proposed, aiming to improve the energy absorption performances of aluminum foam-filled connectors. The multiple pleated (MP) plates and asymmetric pleated (AP) plates were employed for the PU foam-filled energy absorption connectors, which could trigger more plastic hinges and achieve higher energy absorption. Drop-weight impact tests and Finite Element simulations on the PU foam-filled energy absorption connectors were carried out to obtain their deformation modes and energy absorption performances. In addition, an analytical model including strain rate effects of both steel and PU foam was proposed, and it could be employed as a simple alternative to quickly obtain the force–displacement relation of the connector. The accuracy of the developed analytical model was also validated against the experimental and numerical results.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Abedi MM, Niknejad A, Liaghat GH et al (2018) Foam-filled grooved tubes with circular cross section under axial compression: An experimental study. Iran J Sci Technol-Trans Mech Eng 42:401–413
Abramowicz W, Jones N (1986) Dynamic progressive buckling of circular and square tubes. Int J Impact Eng 4:243–270
Azarakhsh S, Rahi A, Ghamarian A et al (2015) Axial crushing analysis of empty and foam-filled brass bitubular cylinder tubes. Thin-Walled Struct 95:60–72
Daneshi GH, Hosseinipour SJ (2002) Grooves effect on crashworthiness characteristics of thin-walled tubes under axial compression. Mater Des 23:611–617
Darvizeh A, Darvizeh M, Ansari R et al (2013) Effect of low density, low strength polyurethane foam on the energy absorption characteristics of circumferentially grooved thick-walled cir-cular tubes. Thin-Walled Struct 71:81–90
Deb A, Shivakumar ND (2009) An experimental study on energy absorption behavior of polyure-thane foams. J Reinf Plas Compos 28:3021–3026
Elahi SA, Rouzegar J, Niknejad A et al (2017) Theoretical study of absorbed energy by empty and foam-filled composite tubes under lateral compression. Thin-Walled Struct 114:1–10
Gilchrist A, Mills NJ (2001) Impact deformation of rigid polymeric foams: experiments and FEA modeling. Int J Impact Eng 25:767–786
Haorongbam B, Deb A, Gupta NK (2017) Behavior of polyurethane foam-filled steel hat sections under axial loading: Testing and simulation. Procedia Eng 173:1349–1356
Hanssen AG, Langseth M, Hopperstad OS (2000) Static and dynamic crushing of circular alu-minium extrusions with aluminium foam filler. Int J Impact Eng 24:475–507
Hussein RD, Ruan D, Lu G et al (2017) Crushing response of square aluminium tubes filled with polyurethane foam and aluminium honeycomb. Thin-Walled Struct 110:140–154
Jafarian B, Rezvani MJ (2017) An experimental investigation on energy absorption of thin-walled bitubal structures by inversion and axial collapse. Int J Mech Sci 126:270–280
Jeong KY, Cheon SS, Munshi MB (2012) A constitutive model for polyurethane foam with strain rate sensitivity. J Mech Sci Technol 26:2033–2038
Koohbor B, Kidane A, Lu WY et al (2016) Investigation of the dynamic stress–strain response of compressible polymeric foam using a non-parametric analysis. Int J Impact Eng 91:170–182
Niknejad A, Elahi SA, Liaghat GH (2012) Experimental investigation on the lateral compression in the foam-filled circular tubes. Mater Des 36:24–34
Niknejad A, Assaee H, Elahi SA et al (2013) Flattening process of empty and polyurethane foam-filled E-glass/vinylester composite tubes – An experimental study. Compos Struct 100:479–492
Niknejad A, Abedi MM, Liaghat GH et al (2015) Absorbed energy by foam-filled quadrangle tubes during the crushing process by considering the interaction effects. Arch Civ Mech Eng 15:376–391
Onsalung N, Thinvongpituk C, Pianthong K (2014) Impact response of circular aluminum tube filled with polyurethane foam. Mater Trans 55:207–215
Reid SR, Reddy TY (1986) Axial crushing of foam-filled tapered sheet metal tubes. Int J Mech Sci 28:643–656
Rezaei B, Niknejad A, Assaee H et al (2015) Axial splitting of empty and foam-filled circular composite tubes – An experimental study. Arch Civ Mech Eng 15:650–662
Song H, Fan Z, Yu G et al (2005) Partition energy absorption of axially crushed aluminum foam-filled hat sections. Int J Solids Struct 42:2575–2600
Wang Y, Zhai X, Ying W et al (2018) Dynamic crushing response of an energy absorption con-nector with curved plate and aluminum foam as energy absorber. Int J Impact Eng 121:119–133
Wang Y, Lu J, Zhai X et al (2019) Response of energy absorbing connector with polyurethane foam and multiple pleated plates under impact loading. Int J Impact Eng 133:103356
Wang Y, Lu J, Zhai X et al (2020) Crushing of energy absorption connectors with polyurethane foam and asymmetric pleated plates. J Constr Steel Res 166:105902
Yan L, Chouw N, Jayaraman K (2014) Lateral crushing of empty and polyurethane-foam filled natural flax fabric reinforced epoxy composite tubes. Compos Part B: Eng 63:15–26
Zhang Z, Sun W, Zhao Y et al (2018) Crashworthiness of different composite tubes by experi-ments and simulations Compos Part B: Eng 143:86–95
Zhou P, Beeh E, Kriescher M et al (2016) Experimental comparison of energy absorption charac-teristics of polyurethane foam-filled magnesium and steel beams in bending. Int J Impact Eng 93:76–87
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Copyright information
© 2023 The Author(s), under exclusive license to Springer Nature Singapore Pte Ltd.
About this chapter
Cite this chapter
Wang, Y. (2023). Polyurethane Foam-Filled Energy Absorption Connectors Under Impact. In: Innovations in Impact and Blast Protections. Springer, Singapore. https://doi.org/10.1007/978-981-19-4375-1_2
Download citation
DOI: https://doi.org/10.1007/978-981-19-4375-1_2
Published:
Publisher Name: Springer, Singapore
Print ISBN: 978-981-19-4374-4
Online ISBN: 978-981-19-4375-1
eBook Packages: EngineeringEngineering (R0)