Abstract
In this paper, a signal processing algorithm to accurately estimate the natural frequencies of structures for early recognition and assessment of cracks is proposed. In standard frequency estimation, the precision increases if the frequency resolution is improved. A finer resolution is achieved by increasing the analysis time interval. Nowadays, there are many other methods to improve the spectrum resolution, as the interpolation of spectral lines, zero-padding, zoom-FFT and so on. The proposed algorithm stepwise crops the acquired vibration signal and performs a spectral analysis. Superposing these spectra, an overlapped spectrum, with a dramatically increased resolution, results. This spectrum offers the possibility to identify very precisely the natural frequencies, even for damages in early stage. The algorithm was tested on generated and real-world signals and was proved to work well, even in the case of fast damped or short signals.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Similar content being viewed by others
References
Doebling S.W., Farrar C.R., Prime M.B., “A summary review of vibration based damage identification methods,” Shock Vibration Digest, 1998, 30(2): 91–105.
Salawu O.S., “Detection of structural damage through changes in frequency: a review,” Engineering Structures, 1997, 19(9): 18–723.
Morassi A., Vestroni F., “Dynamic methods for damage detection in structures,” CISM Courses and Lectures, Vol. 499, Springer Wien New York, 2008.
Gillich G.R., Praisach Z.I., “Modal identification and damage detection in beam-like structures using the power spectrum and time-frequency analysis,” Signal Processing 2014, 96 (PART A): 29–44.
Friswell M.I., “Damage identification using inverse methods,” Phil. Trans. R. Soc. 2007, A 365: 393–410.
Gillich G.R., Praisach Z.I., Wahab M.A., Vasile O., “Localization of transversal cracks in sandwich beams and evaluation of their severity,” Shock and Vibration 2014, Article Number: 607125.
Rytter A., Vibration Based Inspection of Civil Engineering Structures, Ph.D. Thesis, Aalborg University, Denmark, 1993.
Hutin C., “Modal analysis using appropriated excitation techniques,” Sound and Vibration 2000, 34(10): 18–25.
Gillich G.R., Praisach Z.I., Iavornic C.M., “Reliable method to detect and assess damages in beams based on frequency changes,” Proceedings of the ASME International Design Engineering Technical Conferences and Computers and Information in Engineering Conference 2012, Vol. 1: 129–137.
Maia N.M.M, Silva J.M.M., Theoretical and Experimental Modal Analysis, Research Studies Press, Taunton, Somerset, UK, 1997.
National Instruments, LabVIEW Analysis Concepts, March 2004 Edition, Part Number 370192C-01.
Minda A.A., Gillich N., Mituletu I.C., Ntakpe J.L., Manescu T., Negru I., “Accurate frequency evaluation of vibration signals by multi-windowing analysis,” Applied Mechanics and Materials 2015, vol. 801: 328–332.
Chioncel C.P, Gillich N., Tirian G.O., Ntakpe J.L., “Limits of the discrete Fourier transform in exact identifying of the vibrations frequency,” Romanian Journal of Acoustics & Vibration 2015, 12(1): 16–19.
Donciu C., Temneanu M., “An alternative method to zero-padded DFT,” Measurement 2015, 70: 14–20.
Andria G.; Savino M., Trotta A., “Windows and interpolation algorithms to improve electrical measurement accuracy,” IEEE Transactions on Instrumentation and Measurement, 1989, 38 (4): 856–863.
Abed S.T., Dallalbashi Z.E., Taha F.A., “Studying the effect of window type on power spectrum based on MatLab,” Tikrit J. Eng. Sciences 2012, 19(2): 63–70.
Jacobsen E., Kootsookos P., “Fast, accurate frequency estimators,” IEEE Signal Processing Magazine 2007, 123: 123–125.
Candan Ç., “A method for fine resolution frequency estimation from three DFT samples,” IEEE Signal Processing Letters, 2011, 18(6): 351–354.
Voglewede P., “Parabola approximation for peak determination,” Global DSP Mag. 2004, 3(5): 13–17.
Gillich G.R., Praisach Z.I., “Detection and quantitative assessment of damages in beam structures using frequency and stiffness changes,” Key Eng. Mat. 2013, 569: 1013–1020.
Gillich G.R., Birdeanu E.D., Gillich N., Amariei D., Iancu V., Jurcau C.S., “Detection of damages in simple elements,” Proceedings of the International DAAAM Symposium 2009, pp. 623–624.
Gillich G.R., Maia N.M.M., Mituletu I.C., Praisach Z.I., Tufoi M., Negru I., “Early structural damage assessment by using an improved frequency evaluation algorithm,” Latin American Journal of Solids and Structures, 2015, 12(12): 2311–2329.
Mituletu I.C., Gillich N., Nitescu C.N., Chioncel C.P., “A multi-resolution based method to precise identify the natural frequencies of beams with application in damage detection,” Journal of Physics: Conference Series 2015, 628(1), 012020.
Gillich G.R., Mituletu I.C., Negru I., Tufoi M., Iancu V., Muntean F., “A method to enhance frequency readability for early damage detection,” Journal of Vibrational Engineering and Technologies, 2015, 3(5), 1: 637–652.
Acknowledgements
The work has been funded by the Sectoral Operational Programme Human Resources Development 2007–2013 of the Ministry of European Funds through the Financial Agreement POSDRU/159/1.5/S/132395.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2017 Springer International Publishing AG
About this chapter
Cite this chapter
Gillich, G.R., Mituletu, I.C. (2017). Signal Post-processing for Accurate Evaluation of the Natural Frequencies. In: Yan, R., Chen, X., Mukhopadhyay, S. (eds) Structural Health Monitoring. Smart Sensors, Measurement and Instrumentation, vol 26. Springer, Cham. https://doi.org/10.1007/978-3-319-56126-4_2
Download citation
DOI: https://doi.org/10.1007/978-3-319-56126-4_2
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-319-56125-7
Online ISBN: 978-3-319-56126-4
eBook Packages: EngineeringEngineering (R0)