Abstract
In recent years, the conventional construction sector has been noted for its low productivity, as well as being a major generator of CO2 emissions and waste. Faced with this problem, 3D printing has positioned itself as an alternative since, due to a lower consumption of materials, as well as a reduction for waste. Therefore, in recent years, interest in cement-based material for 3D printing has increased in the construction sector as a partial or total replacement for conventional construction methods. Numerous materials have been developed to meet the requirements of 3D printing, such as geopolymers or Engineered Cementitious Composites (ECC). ECC has the capacity for autogenous self-healing, that is, the material presents in its composition the capacity to reduce and heal the possible cracks that are generated. In this study, the focus has been on the development of an ECC material that has the characteristics to achieve structural integrity, reliability, and robustness of 3D printing (A3D_ECC). The main goal of this study is the design and development of a self-healing and efficient eco-cement-based material (eco-A3D_ECC).
The substitution of synthetic fibers (PVA) by natural fibers, spruce, reaches an eco-ECC, eco-A3D_ECC. Fresh properties of the A3D_ECC and eco-A3D_ECC materials are evaluated by consistency, open time, extrudability, and buildability. Hardened properties are researched via compressive and flexural strength for up to 90 days. Meanwhile, the self-healing behavior of A3D_ECC and eco-A3D_ECC is investigated by mechanical recovery test, and absorption and sorptivity tests. For these methods, specimens are cured at room temperature 34 ± 2% RH and 20 ± 2 °C.
This study presents the results of the tests in the fresh and hardened state to know the influence of the natural fibers in the material properties in comparison to synthetic ones. In addition, the research describes the experimental study and also shows the results that confirm the autogenous healing of eco-A3D_ECC when natural fibers are used.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Martin, J.: Productivity in the Construction Industry, UK: 2021. Office for National Statistics (2021)
D’Silva-Parker, E.: Price Movements in Construction Materials and Plant Hire, UK: 2019–2021 (2021)
United Nations Environment Programme. 2022 Global Status Report for Buildings and Construction: Towards a Zero-emission, Efficient and Resilient Buildings and Construction Sector. Nairobi (2022)
Ahmed, G.H.: A review of “3D concrete printing”: Materials and process characterization, economic considerations and environmental sustainability. J. Build. Eng. 66, 105863 (2023)
Rollakanti, C.R., Prasad, C.V.S.R.: Applications, performance, challenges and current progress of 3D concrete printing technologies as the future of sustainable construction – A state of the art review. Mater. Today: Proc. 65, 995–1000 (2022). https://doi.org/10.1016/j.matpr.2022.03.619
Zhang, Z., Liu, S., Yang, F., Weng, Y., Qian, S.: Sustainable high strength, high ductility engineered cementitious composites (ECC) with substitution of cement by rice husk ash. J. Clean. Prod. 317, 128379 (2021)
George, M., Sathyan, D., Mini, K.M.: Investigations on effect of different fibers on the properties of engineered cementitious composites. Mater. Today: Proc. 42(Part 2), 1417–1421 (2021)
Qian, S.Z., Zhou, J., Schlangen, E.: Influence of curing condition and precracking time on the self-healing behavior of engineered cementitious composites. Cem. Concr. Compos. 32(9), 686–693 (2010)
Zhu, Y., Zhang, Z., Chen, X., Zou, D., Guan, X., Dong, B.: Non-destructive methods to evaluate the self-healing behavior of engineered cementitious composites (ECC). Construct. Build. Mater. 230, 116753 (2020)
Zhu, Y., Zhang, Z., Yao, Y., Guan, X., Yang, Y.: Effect of water-curing time on the mechanical properties of engineered cementitious composites. J. Mater. Civ. Eng. 28, 04016123 (2016)
UNE-EN 196-1: Methods of testing cement – Part 1: Determination of strength
UNE-EN 1015-6: Methods of test mortar for masonry. Part 6: Determination of bulk density of fresh mortar
Soltan, D.G., Li, V.C.: A self-reinforced cementitious composite for building-scale 3D printing. Cem. Concr. Compos. 90, 1–13 (2018)
European Standards UNE-EN 83980: Concrete durability. Test methods. Determination of the water absorption, density and accessible porosity for water in concrete
European Standards UNE-EN 83982: Concrete durability. Test methods. Determination of the capillary suction in hardened concrete. Fagerlund method
European Standards UNE-EN 83966: Concrete durability. Test methods. Conditioning of concrete test pieces for the purpose of gas permeability and capilar suction tests
Nodehi, M., Aguayo, F., Nodehi, S.E., Gholampour, A., Ozbakkaloglu, T., Gencel, O.: Durability properties of 3D printed concrete (3DPC). Automat. Construct. 142, 104479 (2022)
Acknowledgments
The authors are thankful to the Comunidad de Madrid for the financial support by the Industrial Doctoral program. Project IND2019-17257.
Author information
Authors and Affiliations
Corresponding authors
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2023 The Author(s), under exclusive license to Springer Nature Switzerland AG
About this paper
Cite this paper
Fernández, F., Jarabo, R., Asensio, E., Guerrero, A. (2023). Natural Fibers for a 3D Printable eco-ECC Material. In: Jędrzejewska, A., Kanavaris, F., Azenha, M., Benboudjema, F., Schlicke, D. (eds) International RILEM Conference on Synergising Expertise towards Sustainability and Robustness of Cement-based Materials and Concrete Structures. SynerCrete 2023. RILEM Bookseries, vol 44. Springer, Cham. https://doi.org/10.1007/978-3-031-33187-9_63
Download citation
DOI: https://doi.org/10.1007/978-3-031-33187-9_63
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-031-33186-2
Online ISBN: 978-3-031-33187-9
eBook Packages: EngineeringEngineering (R0)