Abstract
Drying shrinkage and water absorption are the prominent presenters, describing the durable performance of masonry blended mortars. The present experimental investigation features the resistance toward drying shrinkage and water absorption of binary blended mortars made with eight numbers of different industrial and agricultural by-products. The Portland Cement (PC) was replaced partially with the chemically active by-products for various alteration levels ranging from 5%, 10%, and 15% by weight. The detailed experimental program has been described in two different groups comprising 25 numbers of blended mortar mixes in total which were further cured up to period of 90 days. The findings show that binary blended mortars made with industrial by-products resulted in better resistance toward drying shrinkage and water absorption (due to high reactiveness) compared to agricultural by-products based mortars as well as to that of control mortar. The investigation also infers that usage of the both industrial/agricultural by-products up to the specified amount as an alternative material of PC in blended mortars enhances the resistance toward drying shrinkage and water absorption significantly.
This is a preview of subscription content, log in via an institution to check access.
References
Abdullahi M (2006) Characteristics of wood ASH/OPC concrete. Leonardo Electron J Pract Technol:9–16
Abdulmatin A, Tangchirapat W, Jaturapitakkul C (2018) An investigation of bottom ash as a pozzolanic material. Constr Build Mater 186:155–162. https://doi.org/10.1016/j.conbuildmat.2018.07.101
Adesanya DA, Raheem AA (2009) Development of corn cob ash blended cement. Constr Build Mater 23:347–352. https://doi.org/10.1016/j.conbuildmat.2007.11.013
Adesanya DA, Raheem AA (2010) A study of the permeability and acid attack of corncob ash blended cements. Constr Build Mater 24:403–409. https://doi.org/10.1016/j.conbuildmat.2009.02.001
Alex J, Dhanalakshmi J, Ambedkar B (2016) Experimental investigation on Rice husk ash as cement replacement on concrete production. Constr Build Mater 127:353–362. https://doi.org/10.1016/j.conbuildmat.2016.09.150
Almeida FCR, Klemm AJ (2018) Efficiency of internal curing by superabsorbent polymers (SAP) in PC-GGBS mortars. Cem Concr Compos 88:41–51. https://doi.org/10.1016/j.cemconcomp.2018.01.002
Ankur N, Singh N (2021) Performance of cement mortars and concretes containing coal bottom ash: a comprehensive review. Renew Sust Energ Rev 149:111361. https://doi.org/10.1016/j.rser.2021.111361
ASTM C596 (2018) Standard test method for drying shrinkage of mortar containing hydraulic cement 1
Bahurudeen A, Marckson AV, Kishore A, Santhanam M (2014) Development of sugarcane bagasse ash based Portland pozzolana cement and evaluation of compatibility with superplasticizers. Constr Build Mater 68:465–475
Bureau of Indian Standard (BIS) (2013) IS: 8112–1989, Specification for 43 grade Ordinary Portland Cement
Cheah CB, Ramli M (2011) The implementation of wood waste ash as a partial cement replacement material in the production of structural grade concrete and mortar: an overview. Resour Conserv Recycl 55:669–685. https://doi.org/10.1016/j.resconrec.2011.02.002
Cheng A (2012) Effect of incinerator bottom ash properties on mechanical and pore size of blended cement mortars. Mater Des 36:859–864. https://doi.org/10.1016/j.matdes.2011.05.003
Chi MC (2012) Effects of sugar cane bagasse ash as a cement replacement on properties of mortars. Sci Eng Compos Mater 19:279–285. https://doi.org/10.1515/secm-2012-0014
Chindaprasirt P, Homwuttiwong S, Sirivivatnanon V (2004) Influence of fly ash fineness on strength, drying shrinkage and sulfate resistance of blended cement mortar. Cem Concr Res 34:1087–1092. https://doi.org/10.1016/j.cemconres.2003.11.021
Chowdhury S, Mishra M, Suganya O (2015) The incorporation of wood waste ash as a partial cement replacement material for making structural grade concrete: an overview. Ain Shams Eng J 6:429–437. https://doi.org/10.1016/j.asej.2014.11.005
Chu SH, Kwan AKH (2019) Co-addition of metakaolin and silica fume in mortar: effects and advantages. Constr Build Mater 197:716–724. https://doi.org/10.1016/j.conbuildmat.2018.11.244
Dhir RK, de Brito J, Mangabhai R, Lye CQ (2017) Copper slag in cement manufacture and as cementitious material
Elinwa AU, Ejeh SP (2004) Effects of the incorporation of sawdust waste incineration Fly ash in cement pastes and mortars. J Asian Archit Build Eng 3:1–7. https://doi.org/10.3130/jaabe.3.1
Ettu LO, Anya UC, Awodiji CTG et al (2013) Strength of ternary blended cement Sandcrete containing corn cob ash and pawpaw leaf ash. Int J Eng Res Appl 6:77–82
Feng Y, Zhang Q, Chen Q et al (2019) Hydration and strength development in blended cement with ultrafine granulated copper slag. PLoS One 14:1–15. https://doi.org/10.1371/journal.pone.0215677
Ganesan K, Rajagopal K, Thangavel K (2008) Rice husk ash blended cement: assessment of optimal level of replacement for strength and permeability properties of concrete. Constr Build Mater 22:1675–1683. https://doi.org/10.1016/j.conbuildmat.2007.06.011
Habeeb GA, Fayyadh MM (2009) Rice husk ash concrete: the effect of RHA average particle size on mechanical properties and drying shrinkage. Aust J Basic Appl Sci 3:1616–1622
Hasan ZA (2016) Investigation of drying shrinkage and compressive strength of cement mortar with partial replacement of cement by egg shell powder and milled glass. Al-Qadisiyah J Eng Sci 9:316–330
Hatungimana D, Taşköprü C, İçhedef M et al (2019) Compressive strength, water absorption, water sorptivity and surface radon exhalation rate of silica fume and fly ash based mortar. J Build Eng 23:369–376. https://doi.org/10.1016/j.jobe.2019.01.011
Hemalatha MS, Santhanam M (2018) Characterizing supplementary cementing materials in blended mortars. Constr Build Mater 191:440–459. https://doi.org/10.1016/j.conbuildmat.2018.09.208
Hossain MM, Karim MR, Hasan M et al (2016) Durability of mortar and concrete made up of pozzolans as a partial replacement of cement: a review. Constr Build Mater 116:128–140. https://doi.org/10.1016/j.conbuildmat.2016.04.147
Hu X, Shi Z, Shi C et al (2017) Drying shrinkage and cracking resistance of concrete made with ternary cementitious components. Constr Build Mater 149:406–415. https://doi.org/10.1016/j.conbuildmat.2017.05.113
Ismail I, Bernal SA, Provis JL et al (2013) Influence of fly ash on the water and chloride permeability of alkali-activated slag mortars and concretes. Constr Build Mater 48:1187–1201. https://doi.org/10.1016/j.conbuildmat.2013.07.106
Joshaghani A, Moeini MA (2017) Evaluating the effects of sugar cane bagasse ash (SCBA) and nanosilica on the mechanical and durability properties of mortar. Constr Build Mater 152:818–831. https://doi.org/10.1016/j.conbuildmat.2017.07.041
Joshaghani A, Moeini MA (2018) Evaluating the effects of sugarcane-bagasse ash and rice-husk ash on the mechanical and durability properties of mortar. J Mater Civ Eng 30:1–14. https://doi.org/10.1061/(ASCE)MT.1943-5533.0002317
Jung CT, Siang TC, Kwong TH, Boon K (2019) Compressive strength and water absorption of mortar incorporating silica fume. Int J Civ Eng 6:39–43. https://doi.org/10.14445/23488352/ijce-v6i8p106
Kanthe VN, Deo SV, Murmu M (2018) Effect of fly ash and rice husk ash on strength and durability of binary and ternary blend cement mortar. Asian J Civ Eng 19:963–970. https://doi.org/10.1007/s42107-018-0076-6
Kaur G (2012) Flexural fatigue performance of steel fibre reinforced concrete containing cement additives
Kaur H (2018) Effect of silica fume on the properties of concrete. Int J Eng Technol Sci Res 5:269–272. https://doi.org/10.31695/ijerat.2019.3557
Kim HK, Lee HK (2013) Effects of high volumes of fly ash, blast furnace slag, and bottom ash on flow characteristics, density, and compressive strength of high-strength mortar. J Mater Civ Eng 25:662–665. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000624
Kim Y, Hanif A, Usman M et al (2018) Slag waste incorporation in high early strength concrete as cement replacement: environmental impact and influence on hydration & durability attributes. J Clean Prod 172:3056–3065
Kondraivendhan B, Bhattacharjee B (2015) Flow behavior and strength for fly ash blended cement paste and mortar. Int J Sustain Built Environ 4:270–277. https://doi.org/10.1016/j.ijsbe.2015.09.001
Korde C, Pellegrino C, West RP, Reddy J (2018) Evaluation of pre-early age strength of ggbs mortars. 2nd Int Conf Adv Concr Struct Geotech Eng 613–617
Kumar P, Singh N (2020) Influence of recycled concrete aggregates and coal bottom ash on various properties of high volume fly ash-self compacting concrete. J Build Eng 32:101491. https://doi.org/10.1016/j.jobe.2020.101491
Kumar M, Kumar S, Kumar A (2016) Gulf organisation for research and development sustainable use of industrial-waste as partial replacement of fine aggregate for preparation of concrete – a review. Int J Sustain Built Environ 5:484–516. https://doi.org/10.1016/j.ijsbe.2016.04.006
Lee NK, Jang JG, Lee HK (2014) Shrinkage characteristics of alkali-activated fly ash/slag paste and mortar at early ages. Cem Concr Compos 53:239–248. https://doi.org/10.1016/j.cemconcomp.2014.07.007
Mehta PK, Pitt N (1976) Energy and industrial materials from crop residues. Resour Recover Convers 12:23–38
Memon SA, Javed U, Khushnood RA (2019) Eco-friendly utilization of corncob ash as partial replacement of sand in concrete. Constr Build Mater 195:165–177. https://doi.org/10.1016/j.conbuildmat.2018.11.063
Michael T (2016) Partial replacement of cement with corn cob ash. Int J Innov Res Multidiscip F 2:159–169
Miyandehi BM, Feizbakhsh A, Yazdi MA et al (2016) Performance and properties of mortar mixed with nano-CuO and rice husk ash. Cem Concr Compos 74:225–235. https://doi.org/10.1016/j.cemconcomp.2016.10.006
Mohan A, Mini KM (2018) Strength studies of SCC incorporating silica fume and ultra fine GGBS. Mater Today Proc 5:919–928. https://doi.org/10.1016/j.matpr.2018.10.166
Muangtong P, Sujjavanich S, Boonsalee S et al (2013) Effects of fine bagasse ash on the workability and compressive strength of mortars piyanut muangtong. Chiang Mai J Sci 40:126–134
Nagendran R (2011) Agricultural waste and pollution. In: Waste. Elsevier Inc., pp 341–355
Priya Lakshmi K, Ragupathy R (2016) Effect of sugarcane bagasse ash on strength properties of concrete. Int J Res Eng Technol 05:159–164. https://doi.org/10.15623/ijret.2016.0504030
Ramakrishna G, Sundararajan T (2018) A novel approach to rheological and impact strength of fibre-reinforced cement/cementitious composites for durability evaluation. Elsevier Ltd
Ramos T, Matos AM, Sousa-Coutinho J (2014) Strength and durability of mortar using cork waste ash as cement replacement. Mater Res 17:893–907. https://doi.org/10.1590/S1516-14392014005000092
Rashad AM (2016) A brief review on blast-furnace slag and copper slag as fine aggregate in mortar and concrete based on Portland cement. Rev Adv Mater Sci 44:221–237
Samantasinghar S, Singh SP (2019) Fresh and hardened properties of Fly Ash–Slag blended Geopolymer paste and mortar. Int J Concr Struct Mater 13:1–12. https://doi.org/10.1186/s40069-019-0360-1
Singh N, Arens M (2020) Utilization of industrial and agricultural by-products in blended cement mortars – creating an effort of circular economy in Indian cement industry. In: Eceee industrial summer study proceedings, Gothenburg, pp 91–100
Singh N, Singh SP (2018a) Validation of carbonation behavior of self compacting concrete made with recycled aggregates using microstructural and crystallization investigations. Eur J Environ Civ Eng:1–24
Singh N, Singh SP (2018b) Carbonation resistance of self-compacting recycled aggregate concretes with silica fume. J Sustain Cem Mater 7:214–238. https://doi.org/10.1080/21650373.2018.1471425
Singh J, Singh SP (2019a) Development of alkali-activated cementitious material using copper slag. Constr Build Mater 211:73–79
Singh J, Singh SP (2019b) Synthesis of alkali-activated material using copper slag as source of aluminosilicate. In: UKEIRI Concrete Congress
Singh N, Mithulraj M, Arya S (2019) Utilization of coal bottom ash in recycled concrete aggregates based self compacting concrete blended with metakaolin. Resour Conserv Recycl 144:240–251. https://doi.org/10.1016/j.resconrec.2019.01.044
Singh N, Gupta S, Yashi AP (2020a) Water absorption resistance of binary and Ternery Masnory mortars blended with agricultural by-products. In: Second ASCE India conference on challenges of resilient and sustainable infrastructure development in emerging economics (CRSIDE 2020), Kolkata, pp AIC2020-316–247
Singh N, Nassar R-U-D, Kaur S, Bhardwaj A (2020b) Microstructural characteristics and carbonation resistance of coal bottom ash based concrete mixtures. Mag Concr Res. https://doi.org/10.1680/jmacr.20.00125
Singh N, Shehnazdeep, Bhardwaj A (2020c) Reviewing the role of coal bottom ash as an alternative of cement. Constr Build Mater 233:117276. https://doi.org/10.1016/j.conbuildmat.2019.117276
Singh N, Yashi AP, Gupta S (2020d) Shrinkage behaviour of binary and Ternery Masnory mortars blended with industrial by-products. In: Second ASCE India conference on challenges of resilient and sustainable infrastructure development in emerging economics (CRSIDE 2020), Kolkata, pp AIC2020-316–245
Suresh D, Nagaraju K (2015) Ground granulated blast slag (GGBS) in concrete – a review. IOSR J Mech Civ Eng 12:76–82. https://doi.org/10.9790/1684-12467682
Udoeyo FF, Dashibil PU (2002) Sawdust ash as concrete material. J Mater Civ Eng 14:173–176. https://doi.org/10.1061/(ASCE)0899-1561(2002)14:2(173)
Verma N, Kumar A, Ramteke M, Sahu O (2015) The use of Rice husk improving the final setting time and compressive strength of concrete. Int J Eng Res Technol 4:879–882
Vishnumaya L, Ambi R (2014) Early age properties of silica fume modified cement mortar with M sand as fine aggregate. Int J Eng Res Appl:78–81
Wongkeo W, Thongsanitgarn P, Chaipanich A (2012) Compressive strength and drying shrinkage of fly ash-bottom ash-silica fume multi-blended cement mortars. Mater Des 36:655–662. https://doi.org/10.1016/j.matdes.2011.11.043
Wyrzykowski M, Ghourchian S, Sinthupinyo S et al (2016) Internal curing of high performance mortars with bottom ash. Cem Concr Compos 71:1–9. https://doi.org/10.1016/j.cemconcomp.2016.04.009
Important Websites
https://datatopics.worldbank.org/what-a-waste/trends_in_solid_waste_management.html. Accessed 23 Dec 2020
https://ibm.gov.in/. Accessed 23 Dec 2020
https://mines.gov.in/ViewData/index?mid=1438. Accessed 23 Dec 2020
https://www.globalslag.com/. Accessed 23 Dec 2020
https://www.usgs.gov/centers/nmic/copper-statistics-and-information. Accessed 23 Dec 2020
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2021 The Author(s), under exclusive licence to Springer Nature Switzerland AG
About this entry
Cite this entry
Singh, N., Ankur, N., Ashik Yashi, P., Gupta, S. (2021). Performance of Blended Mortars Containing Industrial and Agricultural By-Products. In: Hussain, C.M., Di Sia, P. (eds) Handbook of Smart Materials, Technologies, and Devices. Springer, Cham. https://doi.org/10.1007/978-3-030-58675-1_145-1
Download citation
DOI: https://doi.org/10.1007/978-3-030-58675-1_145-1
Received:
Accepted:
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-58675-1
Online ISBN: 978-3-030-58675-1
eBook Packages: Springer Reference EngineeringReference Module Computer Science and Engineering