Abstract
A mathematical model is developed for a grinding temperature cycle, invariant to the machining material properties and grinding modes with the managed dimensionless parameters of forced cooling, taking into account the heat exchange and grinding fluid temperature. The influence of these parameters on the dimensionless and dimensional grinding temperature is investigated. A grinding temperature cycle mathematical model includes the heating and cooling stages with and without grinding fluid application. The influence of the grinding fluid temperature and the heat transfer coefficient on the grinding temperature is established. Comparative studies of one- and two-dimensional solutions of the heat conduction differential equation that take into account the forced cooling during grinding have been carried out. The difference in the results of calculating the dimensionless temperature by the solutions of one- and two-dimensional mathematical models does not exceed 4.5–10.6%. The comparison of the two models is performed for the Peclet number with the value of more than 4 which just takes place in contemporary profile grinding.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Lavine AS (1988) A simple model for convective cooling during the grinding process. J Eng Ind 110(1):1–6. https://doi.org/10.1115/1.3187837
Shen B, Shih AJ, Xiao G (2011) A heat transfer model based on finite difference method for grinding. J Manuf Sci Eng 133(3):031001-1–031001-10. https://doi.org/10.1115/1.4003947
Li J, Li JCM (2005) Temperature distribution in workpiece during scratching and grinding. Mater Sci Eng A 409:108–119. https://doi.org/10.1016/j.msea.2005.07.057
Biermann D, Schneider M (1997) Modeling and simulation of workpiece temperature in grinding by finite element analysis. Mach Sci Technol 1(2):173–183. https://doi.org/10.1080/10940349708945645
Westkamper E, Hoffmeister H-W, Weber T (1996) Grinding process simulation with FEM. Prod Eng Res Devel 111(2):45–48
Lin B, Morgan MN, Chen XW, Wang YK (2009) Study on the convection heat transfer coefficient of coolant and the maximum temperature in the grinding process. Int J Adv Manuf Technol 42(11–12):1175–1186. https://doi.org/10.1007/s00170-008-1668-1
Larshin V, Lishchenko N (2018a) Gear grinding system adapting to higher CNC grinder throughput. MATEC Web Conf 226:04033. https://doi.org/10.1051/matecconf/201822604033
Larshin V, Lishchenko N (2019) Adaptive profile gear grinding boosts productivity of this operation on the CNC machine tools. In: Lecture notes in mechanical engineering. Springer, Cham, pp 79–88. https://doi.org/10.1007/978-3-319-93587-4_9
Larshin V, Lishchenko N (2018b) Research methodology for grinding systems. Russ Eng Res 38(9):712–713. https://doi.org/10.3103/S1068798X18090204
Lishchenko NV, Larshin VP (2019) Profile gear grinding temperature determination. In: Proceedings of the 4th international conference on industrial engineering ICIE 2018. Lecture notes in mechanical engineering. Springer, Cham, pp 1723–1730. https://doi.org/10.1007/978-3-319-95630-5_185
Lishchenko NV, Larshin VP (2020) Temperature field analysis in grinding. In: Lecture notes in mechanical engineering. Springer, Cham, pp 199–208. https://doi.org/10.1007/978-3-030-22365-6_20
Lishchenko NV, Larshin VP (2020) Gear-grinding temperature modeling and simulation. In: Lecture notes in mechanical engineering. Springer, Cham, pp 199–208. https://doi.org/10.1007/978-3-030-22063-1_32
Lavine AS, Jen TC (1991) Thermal aspects of grinding. Heat transfer to workpiece, wheel, and fluid. J Heat Transfer 113(2):296–303. https://doi.org/10.1016/S0007-8506(07)62002-2
Lavine AS, Jen TC (1991) Coupled heat transfer to workpiece, wheel, and fluid in grinding, and the occurrence of workpiece burn. Int J Heat Mass Transfer 34(4–5):983–992. https://doi.org/10.1016/0017-9310(91)90009-4
Jen TC, Lavine AS (1995) A variable heat flux model of heat transfer in grinding: model development. J Heat Transf 117(2):473–478. https://doi.org/10.1115/1.2822546
Brinksmeier E, Aurich JC, Govekar E, Heinzel C, Hoffmeister H-W, Klocke F, Peters J, Rentsch R, Stephenson DJ, Uhlmann E, Weinert K, Wittmann M (2006) Advances in modeling and simulation of grinding processes. Annals CIRP 55(2):667–696. https://doi.org/10.1016/j.cirp.2006.10.003
Brinksmeier E, Heinzel C, Wittmann M (1999) Friction, cooling and lubrication in grinding. Annals ClRP 48(21):581–598. https://doi.org/10.1016/S0007-8506(07)63236-3
Sipaylov VA (1978) Teplovye protsessy pri shlifovanii i upravlenie kachestvompoverkhnosti (Thermal processes during grinding and surface quality control). Mashinostroenie, Moscow
Des Ruisseaux NR, Zerkle RD (1970) Temperature in semi-infinite and cylindrical bodies subjected to moving heat sources and surface cooling. J Heat Transf 92(3):456–464. https://doi.org/10.1115/1.3449689
Jaeger JC (1942) Moving sources of heat and temperature at sliding contacts. Proc Royal Soc New South Wales 76:203–224
Larshin VP, Kovalchuk EN, Yakimov AV (1986) Primenenie resheniy teplofizicheskikh zadach k raschetu temperatury i glubiny defektnogo sloya pri shlifovanii. (Application of solutions of thermophysical problems to the calculation of the temperature and depth of the defective layer during grinding). Interuniversity collection of scientific works, Perm, pp 9–16
Carslaw HS, Jaeger JC (1959) Conduction of heat in solids, 2nd edn. Oxford University Press, Oxford
Linke B, Duscha M, Vu AT, Klocke F (2011) FEM-based simulation of temperature in speed stroke grinding with 3D transient moving heat sources. Adv Mater Res 223:733–742. https://doi.org/10.4028/www.scientific.net/AMR.223.733
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2021 The Editor(s) (if applicable) and The Author(s), under exclusive license to Springer Nature Switzerland AG
About this paper
Cite this paper
Lishchenko, N.V., Larshin, V.P., Marchuk, I.V. (2021). Forced Cooling Modeling in Grinding. In: Radionov, A.A., Gasiyarov, V.R. (eds) Proceedings of the 6th International Conference on Industrial Engineering (ICIE 2020). ICIE 2021. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-030-54817-9_133
Download citation
DOI: https://doi.org/10.1007/978-3-030-54817-9_133
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-54816-2
Online ISBN: 978-3-030-54817-9
eBook Packages: EngineeringEngineering (R0)