Abstract
The fatigue phenomena, as being one of the crucial importance for aircraft exploitation life, was investigated with different methods. The most important topic is to determine the state of the material and subsequently the moment of fatigue crack initiation. Many authors investigated the fatigue induced material damage and evolution of structure with different methods i.e.: scanning electron microscopy (Zhang et al. 2008), electron transmission microscopy (Hirsch and Whelan 1960), optical microscopy and two-beam interferometry (Kim and Laird 1978) or /and with modelling (Dingli et al. 2000). Nowadays, as the possibilities of diffraction methods were developed, so the conjoining of the diffraction image with the changes in the material structure can be applied to investigate the fatigue process in materials (Tahara et al. 2009; Huang et al. 2010).
The aim of this work is to find out the relationship between the residual stress and dislocation density evolution applying the X-ray diffraction methods. The dislocations multiply and reorganize during monotonic and cyclic deformation, so their evolution can be a valuable information for investigation of fatigue phenomenon (Huang et al. 2008).
The diffraction methods are non-destructive methods for quantitative analysis of grain level deformation (Korsunsky et al. 2004). In this study X-ray diffraction is employed to acquire the information about the evolution of elastic lattice strains and changes in dislocation density after fatigue cycling of Inconel 718 alloy.
X-ray diffraction has been employed to assess the damage level under high and low cycle fatigue conditions and under the tensile test. The objectives of the work were achieved by two X-ray diffraction techniques: the analysis of residual stresses changes and investigations of changes of full width at half maximum of diffraction peaks which can be a measure of dislocation density changes. The diffraction results were compared to the hardness measurements.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Alloy 718 Round Bar, Plate, Sheet and Coil - AMS 5596, 5662, N07718. United Performance Metals (2015). https://www.upmet.com/products/nickel-alloys/alloy-718. 27 Feb 2019
Brinksmeier, E.: Improvements in X-ray stress analysis. Adv. Surf. Treat. 2, 109–115 (1987)
Cullity, B.D.: Elements of X-Ray Diffraction, 2nd edn. Addison-Wesley, Reading, MA (1978)
Dingli, J.P., Abdul-Latif, A., Saanouni, K.: Predictions of the complex cyclic behavior of polycrystals using a self-consistent modeling. Int. J. Plast. 16(3), 411–437 (2000). https://doi.org/10.1016/S0749-6419(99)00060-1
Hauk, V., Hougardy, H., Macherauch, E. (eds.): Residual stresses: measurement, calculation, evaluation. In: Proc. Conf. on Residual Stresses. DGM informationsgesellschaft, Oberursel (1991)
Hilley, M.E. (ed.): Residual Stress Measurement by X-Ray Diffraction-SAE J784a. Society of Automotive Engineers, Warrendale, PA (1971)
Hirsch, P.B., Whelan, M.J.: A kinematical theory of diffraction contrast of electron transmission microscope images of dislocations and other defects. Phil. Trans. R. Soc. Lond. A 252(1017), 499–529 (1960). https://doi.org/10.1098/rsta.1960.0013
Huang, E.-W., Barabash, R.I., Wang, Y., Clausen, B., Li, L., Liaw, P.K., Ice, G.E., et al.: Plastic behavior of a nickel-based alloy under monotonic-tension and low-cycle-fatigue loading. Int. J. Plast. 24(8), 1440–1456 (2008). https://doi.org/10.1016/j.ijplas.2007.10.001
Huang, E.-W., Barabash, R.I., Clausen, B., Liu, Y.-L., Kai, J.-J., Ice, G.E., Woods, K.P., Liaw, P.K.: Fatigue-induced reversible/irreversible structural-transformations in a ni-based superalloy. Int. J. Plast., Special Issue In Honor of Lallit Anand 26(8), 1124–1137 (2010) https://doi.org/10.1016/j.ijplas.2007.10.001
Inconel Alloy 718. n.d. www.specialmetals.com. http://www.specialmetals.com/assets/smc/documents/inconel_alloy_718.pdf. 27 Feb 2019
Kim, W.H., Laird, C.: Crack nucleation and stage i propagation in high strain fatigue—I. Microscopic and interferometric observations. Acta Metall. 26(5), 777–787 (1978). https://doi.org/10.1016/0001-6160(78)90028-7
Korsunsky, A.M., James, K.E., Daymond, M.R.: Intergranular stresses in polycrystalline fatigue: diffraction measurement and self-consistent modelling. Eng. Fract. Mech., Fract. Damage Mech. 71(4), 805–812 (2004). https://doi.org/10.1016/S0013-7944(03)00018-3
Noyan, I.C., Cohen, J.B.: Residual Stress: Measurement by Diffraction and Interpretation. Springer, New York (2013)
Socha, G., Madejski, B., Krysztofik, J., Czarnewicz, S.: Patent, “Sposób badania struktury materiału wywołanego deformacją trwałą próbki poddanej rozciąganiu i próbka do badania uszkodzenia struktury materiału”, Poland P409294 (2017)
Tahara, M., Kim, H.Y., Hosoda, H., Miyazaki, S.: Cyclic deformation behavior of a Ti–26 at.% Nb Alloy. Acta Mater. 57(8), 2461–2469 (2009). https://doi.org/10.1016/j.actamat.2009.01.037
Zhang, P., Duan, Q.Q., Li, S.X., Zhang, Z.F.: Cyclic deformation and fatigue cracking behaviour of polycrystalline Cu, Cu–10 Wt% Zn and Cu–32 Wt% Zn. Phil. Mag. 88(16), 2487–2503 (2008). https://doi.org/10.1080/14786430802375634
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2020 Springer Nature Switzerland AG
About this paper
Cite this paper
Gadalińska, E., Malicki, M., Madejski, B., Socha, G. (2020). The Influence of Low and High-Cycle Fatigue on Dislocations Density and Residual Stresses in Inconel 718. In: Niepokolczycki, A., Komorowski, J. (eds) ICAF 2019 – Structural Integrity in the Age of Additive Manufacturing. ICAF 2019. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-030-21503-3_42
Download citation
DOI: https://doi.org/10.1007/978-3-030-21503-3_42
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-21502-6
Online ISBN: 978-3-030-21503-3
eBook Packages: EngineeringEngineering (R0)