Abstract
This paper focuses on the effect of drill geometry and cutting parameters on the drilling of 4 shaft satin weave carbon fiber and epoxy matrix. Moreover, two different geometry of drilling tool are selected in this study. Surface quality was evaluated in terms of delamination and superficial defects. It was found that the increasing value of thrust force enhanced serious risk of delamination. The augmentation of thrust force is related to feed rate and drill geometry.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Journal article
Feito, N., Diaz-Alvarez, J., Diaz-Alvarez, A., et al.: Experimental analysis of the influence of drill point angle and wear on the drilling of woven CFRPs. Materials 7, 4258–4271 (2014). https://doi.org/10.3390/ma7064258
Feito, N., Diaz-Alvarez, J., Cantero, J.L., et al.: Influence of special tool geometry in drilling woven CFRPs materials. Sci. Direct Procedia Eng. 132, 632–638 (2015)
Feito, N., Diaz-Alvarez, J., Lopez-Puento, J., Miguelez, M.H., et al.: Experimental and numerical analysis of step drill bit performance when drilling woven CFRPs. Comp. Struct. (2017). https://doi.org/10.1016/j.compstruct.2017.10.061
Grilo, T.J., Paulo, R.M.F., Silva, C.R.M., Davim, J.P.: Experimental delamination analyses of CFRPs using different drill geometries. Compos. Part B 45, 1344–1350 (2013)
Li, M., Leung Soo, S., Aspinwall, D.K., et al.: Study on tool wear and work piece surface integrity following drilling of CFRP laminates with variable feed rate strategy. Sci. Direct Procedia CIRP 71, 407–412 (2018)
Nagaraja, Mervin A.H., Divokara, S., et al.: Effect of process parameters on delamination, thrust force and torque in drilling of carbon fiber epoxy composite. Res. J. Recent Sci. 2(8), 47–51 (2013)
Phadnis, V.A., Makhdum, F., Roy, A., Silberschmidt, V.V.: Drilling in carbon/epoxy composites: experimental investigations and finite element implementation. Compos. Part A 47, 41–51 (2013)
Qui, X., Li, P., Niu, Q., et al.: Influence of machining parameters and tool structure on cutting force and hole wall damage in drilling CFRP with stepped drills. Int. J. Adv. Manuf. Technol. (2018). https://doi.org/10.1007/s00170-018-1981-2
Turki, Y., Habac, M., Velasco, R., et al.: Experimental investigation of drilling damage and stitching effects on the mechanical behavior of carbon/epoxy composites. Int. J. Mach. Manuf. 87, 61–72 (2014a)
Journal article only by DOI
Turki, Y., Hbak, M., Velasco, K., et al.: Influence of cutting forces and damage on 2D and 3D carbon/epoxy composites in drilling (2014b). https://doi.org/10.4028/www.scientific.net/KEM.611-612.1217
Online document
Gornet, L.: Généralités sur les matériaux composites. Ecole d’ingénieurs (2008). < cel-00470296v1>
Acknowledgements
This work is partially supported by Laboratory of Applied Fluid Mechanics. The authors also gratefully acknowledge the helpful comments and suggestions of the reviewers, which have improved the presentation.
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer Nature Switzerland AG
About this paper
Cite this paper
Mahdi, A., Turki, Y., Bouaziz, Z., Habak, M., Bouami, S.E. (2019). Experimental Effect of Cutting Parameters and Tool Geometry in Drilling Woven CFRP. In: Benamara, A., Haddar, M., Tarek, B., Salah, M., Fakher, C. (eds) Advances in Mechanical Engineering and Mechanics. CoTuMe 2018. Lecture Notes in Mechanical Engineering. Springer, Cham. https://doi.org/10.1007/978-3-030-19781-0_17
Download citation
DOI: https://doi.org/10.1007/978-3-030-19781-0_17
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-19780-3
Online ISBN: 978-3-030-19781-0
eBook Packages: EngineeringEngineering (R0)