Volume 76, Issue 1-4 | The International Journal of Advanced Manufacturing Technology

Search all The International Journal of Advanced Manufacturing Technology articles

Volume 76, Issue 1-4

January 2015

Micromanufacturing (pp 1-254)

60 articles in this issue

Editorial by V. K. Jain, I.I.T. Kanpur (India) for the special issue on “Micromanufacturing”
Vijay Kumar Jain
Editorial 27 November 2014 Pages: 1 - 3
Enhancing the biocompatibility of Ti6Al4V implants by laser surface microtexturing: an in vitro study
S. Mukherjee
S. Dhara
P. Saha
ORIGINAL ARTICLE 05 September 2013 Pages: 5 - 15
Investigation and analysis on pulsed Nd:YAG laser micro-turning process of aluminium oxide (Al₂O₃) ceramic at various laser defocusing conditions
G. Kibria
B. Doloi
B. Bhattacharyya
ORIGINAL ARTICLE 24 August 2013 Pages: 17 - 27
An experimental investigation on fabricated TW-ECSM setup during micro slicing of nonconductive ceramic
Alakesh Manna
Amandeep Kundal
ORIGINAL ARTICLE 11 July 2013 Pages: 29 - 37
Generation of microfeatures on stainless steel by electrochemical micromachining
B. Ghoshal
B. Bhattacharyya
ORIGINAL ARTICLE 29 August 2013 Pages: 39 - 50
Influence of electrochemical micromachining parameters during generation of microgrooves
V. Rathod
B. Doloi
B. Bhattacharyya
ORIGINAL ARTICLE 15 September 2013 Pages: 51 - 60
Micromanufacturing by selective jet electrodeposition process
Mridul S. Rajput
Pulak M. Pandey
Sunil Jha
ORIGINAL ARTICLE 13 November 2013 Pages: 61 - 67
Experimental analysis of electro-discharge deposition process
B. Muralidharan
H. Chelladurai
ORIGINAL ARTICLE 27 May 2014 Pages: 69 - 82
Numerical simulation of micro-EDM model with multi-spark
K. P. Somashekhar
S. Panda
N. Ramachandran
ORIGINAL ARTICLE 01 October 2013 Pages: 83 - 90
Multiresponse optimization of micro-wire electrical discharge machining process
B. Kuriachen
K. P. Somashekhar
Jose Mathew
ORIGINAL ARTICLE 11 June 2014 Pages: 91 - 104
Development of mirror like surface characteristics using nano powder mixed electric discharge machining (NPMEDM)
Harmesh Kumar
ORIGINAL ARTICLE 06 June 2014 Pages: 105 - 113
Investigation on shape, size, surface quality and elemental characterization of high-aspect-ratio blind micro holes in die sinking micro EDM
S. Barman
Naga Hanumaiah
A. B. Puri
ORIGINAL ARTICLE 24 August 2013 Pages: 115 - 126
Studies on quality of microholes generated on Al 1100 using micro-electro-discharge machining process
H. K. Dave
V. J. Mathai
H. K. Raval
ORIGINAL ARTICLE 11 January 2014 Pages: 127 - 140
Analysis of micro-electrical discharge drilling characteristics in a thin plate of Ti–6Al–4 V
Koustov Mondol
M. S. Azad
A. B. Puri
ORIGINAL ARTICLE 30 October 2013 Pages: 141 - 150
Study on the influence of micro-EDM process parameters during machining of Ti–6Al–4V superalloy
A. P. Tiwary
B. B. Pradhan
B. Bhattacharyya
ORIGINAL ARTICLE 12 January 2014 Pages: 151 - 160
Micro-grinding characteristics of polycrystalline diamond tool
Ramesh Kuppuswamy
Kerry-Anne Airey
Habib Sardikmen
ORIGINAL ARTICLE 20 August 2014 Pages: 161 - 171
A 2D CFD simulation of MR polishing medium in magnetic field-assisted finishing process using electromagnet
Manas Das
V. K. Jain
P. S. Ghoshdastidar
ORIGINAL ARTICLE 08 May 2014 Pages: 173 - 187
A model for deformation in high energy rate micro forming process
S. R. Sondur
S. V. Pawar
S. B. Patil
ORIGINAL ARTICLE 03 July 2014 Pages: 189 - 197
Tool deflection model for micromilling processes
P. Rodríguez
J. E. Labarga
ORIGINAL ARTICLE 15 May 2014 Pages: 199 - 207
Analysis of tool deflection in micro milling of graphite electrodes
Goran Mijušković
Peter Krajnik
Janez Kopač
ORIGINAL ARTICLE 15 December 2013 Pages: 209 - 217
Evaluation of machine-tool motion accuracy using a CNC machining center in micro-milling processes
Elisa Vázquez
Jéssica Gomar
Ciro A. Rodríguez
ORIGINAL ARTICLE 03 April 2014 Pages: 219 - 228
Dynamic design methodology of high speed micro-spindles for micro/meso-scale machine tools
Guanghui Zhang
Kornel F. Ehmann
ORIGINAL ARTICLE 10 May 2014 Pages: 229 - 246
Fabrication of 3D random microlens array composite optical film with self-assembly
Quang-Cherng Hsu
Yu-Liang Chen
ORIGINAL ARTICLE 02 October 2014 Pages: 247 - 254
Investigation of the effect of tool geometry on friction stir welding of 5083-O aluminum alloy
S. Amini
M. R. Amiri
A. Barani
ORIGINAL ARTICLE 30 August 2014 Pages: 255 - 261
The performance of pressure assisted casting process to improve the mechanical properties of Al-Si-Mg alloys matrix reinforced with coated B₄C particles
Ali Mazahery
Mohsen Ostad Shabani
ORIGINAL ARTICLE 30 August 2014 Pages: 263 - 270
Composite error prediction of multistage machining processes based on error transfer mechanism
Genbao Zhang
Yan Ran
Tian Gao
ORIGINAL ARTICLE 30 August 2014 Pages: 271 - 280
A computer vision-based assistant system for the assembly of narrow cabin products
Yi Liu
ShiQi Li
JiPing Lu
ORIGINAL ARTICLE 30 August 2014 Pages: 281 - 293
Solving continuous single-objective defensive location problem based on hybrid directed tabu search algorithm
Raheleh Khanduzi
M. Reza Peyghami
H. Reza Maleki
ORIGINAL ARTICLE 30 August 2014 Pages: 295 - 310
On artificial neural networking-based process monitoring under bootstrapping using runs rules schemes
Babar Zaman
Muhammad Riaz
Saddam Akber Abbasi
ORIGINAL ARTICLE 30 August 2014 Pages: 311 - 327
Review of improvements in wire electrode properties for longer working time and utilization in wire EDM machining
Ibrahem Maher
Ahmed A. D. Sarhan
M. Hamdi
ORIGINAL ARTICLE 30 August 2014 Pages: 329 - 351
Using upper bound solution to analyze force parameters of three-roll cross rolling of rings with small hole and deep groove
Lin Hua
Jiadong Deng
Qi Ma
ORIGINAL ARTICLE 30 August 2014 Pages: 353 - 366
Automatic control of WEDM servo for silicon processing using current pulse probability detection
Liu Zhidong
Chen Haoran
Tian Zongjun
ORIGINAL ARTICLE 30 August 2014 Pages: 367 - 374
Concurrent fixture design for automated manufacturing process planning
Wentao Fu
Matthew I. Campbell
ORIGINAL ARTICLE 31 August 2014 Pages: 375 - 389
CAD/CAE integration: updating the CAD model after a FEM analysis
Borhen Louhichi
Gad N. Abenhaim
Antoine S. Tahan
ORIGINAL ARTICLE 31 August 2014 Pages: 391 - 400
Optimization of thrust, torque, entry, and exist delamination factor during drilling of CFRP composites
Kumar Abhishek
Saurav Datta
Siba Sankar Mahapatra
ORIGINAL ARTICLE 31 August 2014 Pages: 401 - 416
Discovering task assignment rules for assembly line balancing via genetic programming
Adil Baykasoğlu
Lale Özbakır
ORIGINAL ARTICLE 02 September 2014 Pages: 417 - 434
Welding process of consumable double electrode with a single arc GMAW
H. L. Wei
H. Li
L. J. Yang
ORIGINAL ARTICLE 02 September 2014 Pages: 435 - 446
Improving accuracy of curved corners in wire EDM successive cutting
Hamid Abyar Firouzabadi
Jamshid Parvizian
Amir Abdullah
ORIGINAL ARTICLE 02 September 2014 Pages: 447 - 459
A bi-objective imperialist competitive algorithm for no-wait flexible flow lines with sequence dependent setup times
Majid Khalili
Bahman Naderi
ORIGINAL ARTICLE 02 September 2014 Pages: 461 - 469
Optimization of operator allocation in a large multi product assembly shop through unique integration of simulation and genetic algorithm
A. Azadeh
S. M. Asadzadeh
S. Tadayoun
ORIGINAL ARTICLE 02 September 2014 Pages: 471 - 486
Numerical and experimental studies on grind-hardening cylindrical surface
Liu Songyong
Yang Gang
Liu Xiaohui
ORIGINAL ARTICLE 04 September 2014 Pages: 487 - 499
Fabrication of through-hole with biconically shaped cross sections by using electroforming and inert metal mask electrochemical machining
Pingmei Ming
Xiaohui Bao
Juntao Wang
ORIGINAL ARTICLE 04 September 2014 Pages: 501 - 512
Prognosis of the probability of failure in tool condition monitoring application-a time series based approach
Yue Wu
G. S. Hong
W. S. Wong
ORIGINAL ARTICLE 05 September 2014 Pages: 513 - 521
A new process chain for producing bulk metallic glass replication masters with micro- and nano-scale features
Pierre C. Vella
Stefan S. Dimov
Ben R. Whiteside
ORIGINAL ARTICLE 05 September 2014 Pages: 523 - 543
Integrated system for analyzing maintenance records in product improvement
Susanne Dienst
Fazel Ansari
Madjid Fathi
ORIGINAL ARTICLE 05 September 2014 Pages: 545 - 564
Framework to evaluate manufacturing capability using analytical hierarchy process
R. R. Lekurwale
M. M. Akarte
D. N. Raut
ORIGINAL ARTICLE 05 September 2014 Pages: 565 - 576
Springback evaluation in hot v-bending of Ti-6Al-4V alloy sheets
Yingying Zong
Po Liu
Debin Shan
ORIGINAL ARTICLE 05 September 2014 Pages: 577 - 585
Effect of posttreatments on the performance of tungsten carbide (K20) tool while machining (turning) of Inconel 718
D. G. Thakur
B. Ramamoorthy
L. Vijayaraghavan
ORIGINAL ARTICLE 05 September 2014 Pages: 587 - 596
Effect of machining-induced residual stress on the distortion of thin-walled parts
Soroush Masoudi
Saeid Amini
Hamdollah Eslami-Chalander
ORIGINAL ARTICLE 05 September 2014 Pages: 597 - 608
Influence of different cooling methods on drill temperature in drilling GFRP
K. Jessy
S. Satish kumar
V. Seshagiri Rao
ORIGINAL ARTICLE 05 September 2014 Pages: 609 - 621