Abstract
Much attention is given to the theoretical and technological methods behind stamping simulation models; however the applicability of these models in the productive completion of a comprehensive digital process plan is often overlooked. The role that simulation models play in the development process must consider the alignment of software usage, the available inputs, and the desired outputs supporting the work process, in addition to the software capabilities.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
Abbreviations
- a, m, p :
-
exponents in the Swift-Hockett/Sherby strain hardening law
- C :
-
coefficient in the Swift-Hockett/Sherby strain hardening law
- M :
-
exponent in the BBC 2005 yield criterion
- R m :
-
tensile strength
- R p0.2 :
-
yield stress
- r 0, r 45, r 90 :
-
anisotropy coefficients in the rolling, diagonal and transversal directions
- r b :
-
biaxial anisotropy coefficient
- α :
-
coefficient in the Swift/Hockett/Sherby strain hardening law
- ɛ 0 :
-
pre-strain
- ɛ pl :
-
plastic strain
- σ :
-
equivalent stress
- σ b :
-
biaxial yield stress
- σ i :
-
initial stress
- σ Sat :
-
saturation stress
- σ 0, σ 45, σ 90 :
-
yield stresses in the rolling, diagonal and transversal directions
References
Kleiner M et al. (2002) Material parameters for sheet metal forming simulations by means of optimization algorithms. Final Report of the European Project 7210-PR-244, Research Fund for Coal and Steel (RFCS)
AutoForm 4.1 Software Manual. (2007) AutoForm Engineering GmbH, Zurich
Sigvant M, Mattiasson K, Vegter H, Thilderkvist P (2009) A viscous pressure bulge test for the determination of plastic hardening curve and equibiaxial material data. International Journal of Material Forming, 2:235–242
Hosford WF (1996) On the crystallographic basis of yield criteria. Texture and Microstructures 26–27:479–493
Mattiasson K, Sigvant M (2004) Material characterization and modeling for industrial sheet forming simulations. In: Ghosh S, Lee JK, Castro JC (eds) Proceedings of the NUMIFORM 2004, AIP, New York, NY, 875–880
Forming of new metallic materials. Brite Euram Project, 1996–1999.
Sigvant M, Mattiasson K, Skogsgårdh A (2007) Industrial experiences of stochastic simulations of sheet metal forming In: Hora P (ed) Proceedings of the Application Stochastics and Optimization Methods, Zürich, 23–31
Bonte MHA et al. (2006) Optimizing towards robust metal forming processes. In: Juster N, Rosochowski A (eds) Proceedings of the International Conference on Material Forming ESAFORM 2006, Glasgow, 47–51
Dietrich E, Schulze A (2005) Statistische Verfahren zur Maschinen- und Prozessqualifikation, Hanser Verlag, Munchen
Carleer B (2006) Applicability of stochastical methods in the control of the scatter influence of constitutive parameters. Proceedings of the FLC Conference, March 15th–16th 2006, Zürich
Lee CH (2006) Application of AutoForm Sigma on a hood inner. Proceedings of the 5th Press Forming Symposium, Korean Society of Technology for Plasticity, Jeju Island, June 2006
Xu WL, Ma CH, Li CH, Feng WJ (2004) Sensitive factors in springback simulation for sheet metal forming. Journal of Materials Processing Technology 151:217–222
Valente F, Li XP, Messina A (1997) Springback prediction for stamping tools compensation by numerical simulation. Centro Ricerche Fiat, Torino
Chung WJ, Cho JW, Belytschko T (1996) A study on dynamic effects of dynamic explicit FEM in sheet metal forming analysis. In: Lee JK Kinzel JL, Wagoner RH (eds) Proceedings of the NUMISHEET’96 Conference, Columbus, OH, 414–426
Lin Z, Liu G (2000) Study on the effects of numerical parameters on the precision of springback prediction. Proceedings of the 6th International LS_DYNA User’s Conference, Session 13C, Dearbon, MI
Huang M, Gerdeen JC (1994) Springback of doubly curved developable sheet metal surface – An overview. SAE Technical Paper No. 940938, 718–731
Makinouchi A, Nakamachi E, Onate E, Wagoner RH (eds) (1993) Proceeding of the 2nd International Conference and Workshop on Numerical Simulation of 3D Sheet Metal Forming Processes, Isehara
Kubli W, Anderheggen E, Reissner J (1991) Nonlinear solver with uncoupled bending and stretching deformation for simulating thin sheet metal forming. Proceedings of the 1st International Conference and Workshop on Numerical Simulation of 3D Sheet Metal Forming Processes, VDI, Dusseldorf, 325–343
Yang DY, Hug H, Oh SI, Kim YH (eds) (2002) Proceedings of the 5th International Conference and Workshop on Numerical Simulation of 3D Sheet Metal Forming Processes-Verification of Simulation with Experiment, Jeju Island
Li K, Wagoner RH (1998) Simulation of springback. In: Huetink J, Baaijens FPT (eds) Simulation of Materials Processing: Theory, Methods and Applications. Proceedings of the 6th International Conference on NUMIFORM 1998, Enschede, 21–31
Wagoner RH, Li M (2005) Advances in springback. In: Smith LM, Pourboghrat F, Yoon JW, Stoughton TB (eds) Proceedings of the 6th International Conference and Workshop on Numerical Simulation of 3D Sheet Metal Forming Processes-Verification of Simulation with Experiment, Numisheet 2005, Detroit, 209–214
Smith LM, Pourboghrat F, Yoon JW, Stoughton TB (eds) Proceedings of the 6th International Conference and Workshop on Numerical Simulation of 3D Sheet Metal Forming Processes-Verification of Simulation with Experiment, Numisheet 2005, Detroit
Hora P (ed) (2008) Proceedings of the 7th International Conference and WorkShop on Numerical Simulation of 3D Sheet Metal Forming Processes-Verification of Simulation with Experiment, Numisheet 2008, Interlaken
Roll K, Lemke T, Wiegand K (2005) Possibilities and strategies for simulation and compensation for springback. In: Smith LM, Pourboghrat F, Yoon JW, Stoughton TB (eds) Proceedings of the 6th International Conference and Workshop on Numerical Simulation of 3D Sheet Metal Forming Processes-Verification of Simulation with Experiment, Numisheet 2005, 295–302
Schoenbach T, Bauer T (2008) New method to calculate and compensate springback. In: Hora P (ed) (2008) Proceedings of the 7th International Conference and Workshop on Numerical Simulation of 3D Sheet Metal Forming Processes-Verification of Simulation with Experiment, Numisheet 2008, Interlaken, 515–520
AutoForm Release Notes 4.0 (2005) AutoForm Engineering. GmbH, Zurich
Acknowledgements
Finally, I would like to thank all my colleagues, especially Thomas Schoenbach, who were involved in the preparation of this subchapter.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
Copyright information
© 2010 Springer-Verlag Berlin Heidelberg
About this chapter
Cite this chapter
Banabic, D. (2010). Numerical Simulation of the Sheet Metal Forming Processes. In: Sheet Metal Forming Processes. Springer, Berlin, Heidelberg. https://doi.org/10.1007/978-3-540-88113-1_4
Download citation
DOI: https://doi.org/10.1007/978-3-540-88113-1_4
Published:
Publisher Name: Springer, Berlin, Heidelberg
Print ISBN: 978-3-540-88112-4
Online ISBN: 978-3-540-88113-1
eBook Packages: EngineeringEngineering (R0)