Abstract
Stiffened plate panel is the major structural part of a fabrication industry where fillet welding joint is one of the most important fabrication techniques. Large stiffened structures are generally joined by several welding passes which generates thermal stresses and angular deformation. Tensile residual stresses which are generated due to welding in the weld region may lead to early failure of the structure when subjected to cyclic loading. The weld-induced residual distortion causes dimensional inaccuracy and needs rework to achieve the desired shape. Use of multiple welding passes without any optimized welding sequences typically leads to an increased degree of nonuniform heating and cooling, i.e., creating complex welding residual stress and angular deformation in the structure. In this present study, the effect of four different welding sequences on submerged arc welded fillet joint has been studied. A finite element-based numerical model has been developed to predict the thermal profile, welding residual stress, and angular deformation. The developed model considers temperature-dependent material property and material deposition by using element death and birth technique. The results have been compared with experimental one. In the effect of welding sequence on residual stress, angular deformation has been studied. Thus, the developed model presents the effect of welding sequence on the weld induced residual stresses and distortions which provide one of the most optimal welding sequence for enhanced fabrication process.
Similar content being viewed by others
References
Biswas P, Mandal NR, Das S (2011) Prediction of welding deformations of large stiffened panels using average plastic strain method. Science and Technology of Welding and Joining 16(3):227–231
Gannon L, Liu Y, Pegg N, Smith MJ (2013) Effect of three-dimensional welding-induced residual stress and distortion fields on strength and behaviour of flat-bar stiffened panels. Ships and Offshore Structures 8(5):565–578
Khan I, Zhang S (2011) effects of welding-induced residual stress on ultimate strength of plates and stiffened panels. Ships and Offshore Structures 6(4):297–309
Paik JK, Sohn JM (2012) Effects of welding residual stresses on high tensile steel plate ultimate strength: nonlinear finite element method investigations. Journal of Offshore Mechanics and Arctic Engineering 134(2):021401-1–021401-6
Yadaiah N, Bag S (2014) Development of egg-configuration heat source model in numerical simulation of autogenous fusion welding process. Int J Therm Sci 86:125–138
Alberg, H., Simulation of welding and heat treatment modelling and validation, PhD thesis, 2005, Luleå University of Technology, Sweden
Tsai CL, Cheng WT (1999) Welding distortion of thin-plate panel structures. Weld J (5):78, 156s–165s
Tsai CL, Jung GH (2004) Plasticity-based distortion analysis for fillet welded thin- plate T-joints. Weld J 83(6):177s–187s
Biswas P, Kumar DA, Mandal NR, Mahapatra MM (2011) A study on the effect of welding sequence in fabrication of large stiffened plate panels. J Mar Sci Appl 10:429–436
Gannon L, Liu Y, Pegg N, Smith M (2010) Effect of welding sequence on residual stress and distortion in flat-bar stiffened plates. Mar Struct 23:385–404
Kohandehghan AR, Serajzadeh S (2012) Experimental investigation into the effects of weld sequence and fixture on residual stresses in arc welding process. Journal of Materials Engineering and Performance 21(6):892–899
Perić M, Tonković Z, Rodić A, Surjak M, Garašić I, Boras I, Švaić S (2014) Numerical analysis and experimental investigation of welding residual stresses and distortions in a T-joint fillet weld. Mater Des 53:1052–1063
Podder D, Mandal NR, Das S (2014) Heat source modeling and analysis of submerged arc welding. Weld J 93:183–192
Biswas P, Mandal NR (2010) Thermomechanical finite element analysis and experimental investigation of single-pass single-sided submerged arc welding of C-Mn steel plates. Proceedings of the Institution of Mechanical Engineers, Part B: Journal Engineering Manufacture 224(B4):627–639
Wang J, Ma N, Murakawa H, Teng B, Yuan S (2011) Prediction and measurement of welding distortion of a spherical structure assembled from multi thin plates. Mater Des 32:4728–4737
Lindgren LE (2001) Finite element modeling and simulation of welding. Part 2: improved material modeling. J Therm Stresses 24:195–231
Fanous FZI, Maher YA, Wifi SA (2003) 3-D finite element modeling of the welding process using element birth and element movement techniques. Transactions ASME, Journal of Pressure Vessel Technology 125:144–150
Biswas P, Mahapatra MM, Mandal NR (2009) Numerical and experimental study on prediction of thermal history and residual deformation of double-sided fillet welding. Proceedings of the Institution of Mechanical Engineers, Part-B 224:125–134
Martin, B. S. (1999) Simulation of welding distortions in ship section, PhD thesis, Department of naval architecture and offshore engineering, Technical University of Denmark
Wen SW, Hilton P, Farrugia DDJ (2001) Finite element modelling of a submerged arc welding process. Journals of Materials Processing Technology 119:203–209
Malik, M. A., Qureshi, E. M., and Dar, N. M. (2007) Numerical simulation of arc welding investigation of various process and heat source parameters, Failure of Engineering Materials & Structures, UET TAXILA Mechanical Engineering Department pp. 127–141
Sharma A, Chaudhary AK, Arora N, Mishra BK (2009) Estimation of heat source model parameters for twin-wire submerged arc welding. Int J Adv Manuf Technol 45:1096–1103
Bag S, Kiran DV, Syed AA, De A (2012) Efficient estimation of volumetric heat source in fusion welding process simulation. Welding in the world 56:88–97
Yadaiah N, Bag S (2012) Effect of heat source parameters in thermal and mechanical analysis of linear GTA welding process. The Iron and Steel Institute of Japan 52:2069–2075
Stamenković D, Vasović I (2009) Finite element analysis of residual stress in butt welding two similar plates. Scientific Technical Review 59(1):57–60
Mondal, A. K., Bag, S. and Biswas P. (2013) “3-D finite element analysis of effect of process parameters on residual stresses of saw butt joint”, 7th Asia Pacific IIW International Congress. Singapore, 8–10
Mondal, A. K., Ranjan, R., Bag, S., Biswas P. and Mahapatra, M. M. (2012) Finite element analysis of weld induced residual stress of double sided fillet welded joint. 21st International Symposium on Processing and Fabrication of Advanced Materials (PFAM-21), IIT Guwahati, 10–13
Adak M, Soares GC Effects of different restraints on the weld-induced residual deformations and stresses in a steel plate. Int J Adv Manuf Technol 71(1):699–710
Chen, B. Q., Adak, M., and Soares, G. C. (2012) Numerical investigations to study the effect of weld parameters on the temperature-time history in steel plates. Maritime Engineering and Technology Maritime Engineering and Technology Edited by Santos T. A. CRC Press, pp. 285–292
Nart E, Celik Y (2013) A practical approach for simulating submerged arc welding process using FE method. J Constr Steel Res 84:62–71
Jiang W, Yahiaoui K, Hall FR (2005) Finite element predictions of temperature distributions in a multipass welded piping branch junction. Trans ASME Journal of Pressure Vessel and Technology 127:7–12
Kanjilal P, Pal TK, Majumdar SK (2006) Combined effect of flux and welding parameters on chemical composition and mechanical properties of submerged arc weld metal. J Mater Process Technol 171:223–231
Liang W, Murakawa H, Deng D (2015) Investigation of welding residual stress distribution in a thick-plate joint with an emphasis on the features near weld end-start. Mater Des 67:303–312
Kiran DV, Cho D-W, Song W-H, Na S-J (2014) Arc behavior in two wire tandem submerged arc welding. J Mater Process Technol 214:1546–1556
Armentani E, Esposito R, Sepe R (2007) The effect of thermal properties and weld efficiency on residual stresses in welding. Journal of Achievements in Materials and Manufacturing Engineering 20:319–322
Tarng YS, Juang SC, Chang CH (2002) The use of grey-based Taguchi methods to determine submerged arc welding process parameters in hardfacing. J Mater Process Technol 128:1–6
Zhao D, Wanga Y, Lin Z, Sheng SM (2013) An effective quality assessment method for small scale resistance spot welding based on process parameters. Independent Nondestructive Testing and Evaluation International 55:36–41
Shen S, Oguocha INA, Yannacopoulos S (2012) Effect of heat input on weld bead geometry of submerged arc welded ASTM A709 Grade 50 steel joints. J Mater Process Technol 212:286–294
Nowacki J, Rybicki P (2005) The influence of welding heat input on submerged arc welded duplex steel joints imperfections. J Mater Process Technol 164–165:1082–1088
Ma N, Li L, Huang H, Chang S, Murakawa H (2015) Residual stresses in laser-arc hybrid welded butt-joint with different energy ratios. J Mater Process Technol 220:36–45
Akbari Mousavi SAA, Miresmaeili R (2008) Experimental and numerical analysis of residual stress distribution in TIG welding process for 304L stainless steel. J Mater Process Technol 208:383–394
Jun T-S, Korsunsky AM (2010) Evaluation of residual stresses and strains using the eigenstrain reconstruction method. Int J Solids Struct 47:1678–1686
Teng T-L, Fung C-P, Chang P-H, Yang W-C (2001) Analysis of residual stresses and distortions in T-joint fillet welds. Int J Press Vessel Pip 78:523–538
Brown S, Song H (1992) Implication of three-dimensional numerical simulation of welding of large structures. Weld J 71(2):55s–62s
Michaleris P, DeBiccari A (1997) Prediction of welding distortion. Weld J 76(4):172s–180s
Author information
Authors and Affiliations
Corresponding author
Additional information
Recommended for publication by Commission X - Structural Performances of Welded Joints - Fracture Avoidance
Rights and permissions
About this article
Cite this article
Mondal, A.K., Biswas, P. & Bag, S. Prediction of welding sequence induced thermal history and residual stresses and their effect on welding distortion. Weld World 61, 711–721 (2017). https://doi.org/10.1007/s40194-017-0468-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s40194-017-0468-3