Abstract
This paper illustrates the utilisation of an optically accessible high-pressure sector test rig in combination with optical test methods as part of the development process of a lean injection combustion concept. First experimental results from a new single sector combustor are presented. The combustor allows the investigation of large burners for lean aero-engine combustion at full size and medium pressure up to 20 bar with wide optical access to the primary zone. Imaging and laser-based techniques are used to characterise fuel preparation, heat release and temperature. Gas analysis at the outlet of the combustor provides emission results, to which the flow field data can be related. The measurements focused on part load operation from idle to cruise, including pilot-only operation at idle to varying degrees of fuel staging at cruise. The circumferential homogeneity of the main fuel placement was also investigated. The measurements on the pilot injector demonstrated the influence of fuel loading on the pilot combustion at real operating conditions. Transition from attached to lifted flames was observed for different injector hydraulics but identical aerodynamics. The fuel staging variation showed the shift from a main combustion zone separated from the pilot to joint combustion zones and finally to combustion concentrated near the pilot. This global behaviour was linked to measurements of NOx and combustion efficiency. The measurement plane parallel to the combustor head revealed a near field periodicity of the fuel placement coinciding with vanes in the outer passage. Overall circumferential homogeneity increased with fuel loading. A first 3D dataset of temperature is presented, demonstrating the future potential to correlate different measurement variables, e.g. fuel concentration, temperature or velocity on arbitrary surfaces or volumes in the primary zone.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Schneider, D., Meier, U., Quade, W., Koopman, J., Aumeier, T., Langfeld, A., Behrendt, T., Hassa, C., Rackwitz, L.: A new test rig for laser optical investigations of lean jet engine burners. In: 27th International Congress of the Aeronautical Sciences (ICAS 2010)
Hassa, C., Heinze, J., Rackwitz, L., Doerr, Th.: Validation methodology for the development of low emission fuel injectors for aero-engines. In: 25th International Congress of the Aeronautical Sciences (ICAS 2006)
Dupoirieux, F.: Optical diagnostics used at Onera to characterize turbulent reactive flows and to validate aero- and rocket engine combustor modeling. Aerospace Lab—The ONERA Journal, Issue 1, Dec. 2009; ISSN: 2107-6596 (2009)
Burrus, D.L., Johnson, A.W., Roquemore, W. M., Shouse, D. T.: Performance assessment of a prototype trapped vortex combustor concept for gas turbine application. In: Proceedings of ASME TURBO EXPO 2001, June 4–7, 2001, New Orleans, Louisiana, paper 2001-GT-0087
Hicks, Y.R., Locke, R.J., Wey, C.C., Bianco, J.: a unique, optically accessible flame tube facility for lean combustor studies. NASA Technical Memorandum 107073 prepared for the 31st Joint Propulsion Conference and Exhibit, San Diego, California, July 10–12, 1995
Lazik, W., Dörr, T., v.d. Bank, R., Bake, S., Rackwitz, L.: Development of lean-burn low-NOx combustion technology at Rolls-Royce Deutschland. ASME Turbo Expo GT2008-51115 (2008)
Behrendt, T., Frodermann, M., Hassa, C., Heinze, J., Lehmann, B., Stursberg K.: Optical Measurements of spray combustion in a single sector combustor from a practical fuel injector at higher pressures. RTO Applied Vehicle Technology Panel, Symp. on Gas Turbine Engine Combustion, Emissions and Alternative Fuels, Lisbon, 12–16 Oct (1998)
Kohse-Höinghaus, K., Jeffries, J.B. (eds.): Applied Combustion Diagnostics. Taylor and Francis, ISBN 1-56032-913-0 (2002)
Meier, U.E., Wolff-Gassman, D., Stricker, W.: LIF imaging and 2D temperature mapping in a model combustor at elevated pressure. Aerosp Sci Technol 4, 403–414 (2000)
Dasch, C.J.: One-dimensional tomography: a comparison of Abel, onion-peeling, and filtered backprojection methods. Appl. Opt. 31(8), 1146–1152 (1992)
Guy, S.R.D., Allan, W.D.E., LaViolette, M., Underhill, P.R.: Optical patternation of gas turbine fuel sprays during simulated engine operating conditions. In: Proceedings of ASME Turbo Expo 2009: Power for Land, Sea and Air, June 8–12, Orlando, Florida, USA, GT2009-59011 (2009)
Acknowledgments
This work received funding from the European Community through the FP6 Aeronautics and Space programme, project NEWAC (Project # FP6-030876). It reflects only the author’s views and the Community is not liable for any use that may be made of the information contained therein.
Author information
Authors and Affiliations
Corresponding author
Additional information
This paper is based on a presentation at the German Aerospace Congress, September 27–29, 2011, Bremen, Germany.
Rights and permissions
About this article
Cite this article
Meier, U., Heinze, J., Lange, L. et al. Characterisation of the combustion performance of low emission fuel injectors with laser measurements. CEAS Aeronaut J 3, 45–53 (2012). https://doi.org/10.1007/s13272-012-0042-z
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s13272-012-0042-z