Abstract
The service life of a diesel fuel injector is highly affected by the tribological properties of the fuel. This study aims to investigate the friction and wear behaviors of emulsified bio-oil (EBO), which is a very promising alternative fuel for engines. Sliding wear tests were performed with a ball-on-disk tribometer using a GCr15 steel ball and a flat specimen as a counterpart. In these tests, the total sliding distance was 500 m, the load ranged from 10 to 20 N, and the oscillation frequency ranged from 30 to 50 Hz. Experimental results showed that EBO had better tribological properties than diesel oil and crude bio-oil. Contact load and oscillation frequency significantly influenced friction coefficient, wear volume, and wear damage pattern. The friction coefficient decreased with an increase in load and increased with an increase in oscillation frequency. Furthermore, the wear volume slightly increased with an increase in load or oscillation frequency. The damage mechanism is attributed to adhesive wear under low load and to abrasive wear under high load. The transition in the wear mechanism is related to the adsorption of the molecules in the EBO, the microstructural contact surface, and the mechanical actions.
Similar content being viewed by others
References
Xu, Y.F., Yu, H.Q., Wei, X.Y., Cui, Z., Hu, X.G., Xue, T., Zhang, D.Y.: Friction and wear behaviors of a cylinder liner-piston ring with emulsified bio-oil as fuel. Tribol. T 56, 359–365 (2013)
Daroch, M., Geng, S., Wang, G.: Recent advances in liquid biofuel production from algal feedstocks. Appl. Energ. 102, 1371–1381 (2013)
Yang, Y., Brammer, J.G., Ouadi, M., Samanya, J., Hornung, A., Xu, H.M., Li, Y.: Characterisation of waste derived intermediate pyrolysis oils for use as diesel engine fuels. Fuel 103, 247–257 (2013)
Zhang, X., Wang, T., Ma, L., Zhang, Q., Jiang, T.: Hydrotreatment of bio-oil over Ni-based catalyst. Bioresource Technol. 127, 306–311 (2013)
Xu, Y., Zheng, X., Yu, H., Hu, X.: Hydrothermal liquefaction of Chlorella pyrenoidosa for bio-oil production over Ce/HZSM-5. Bioresource Technol. 156, 1–5 (2014)
Ott, L.S., Smith, B.L., Bruno, T.J.: Advanced distillation curve measurement: application to a bio-derived crude oil prepared from swine manure. Fuel 87, 3379–3387 (2008)
De Silva, P.R., Priest, M., Lee, P.M., Coy, R.C., Taylor, R.I.: Tribometer investigation of the frictional response of piston rings when lubricated with the separated phases of lubricant contaminated with the gasoline engine biofuel ethanol and water. Tribol. Lett. 43, 107–120 (2011)
Suarez, P.A.Z., Moser, B.R., Sharma, B.K., Erhan, S.Z.: Comparing the lubricity of biofuels obtained from pyrolysis and alcoholysis of soybean oil and their blends with petroleum diesel. Fuel 88, 1143–1147 (2009)
Agarwal, S., Chhibber, V.K., Bhatnagar, A.K.: Tribological behavior of diesel fuels and the effect of anti-wear additives. Fuel 106, 21–29 (2013)
Galle, J., Verhelst, S., Sierens, R., Goyos, L., Castaneda, R., Verhaege, M., Vervaeke, L., Bastiaen, M.: Failure of fuel injectors in a medium speed diesel engine operating on bio-oil. Biomass Bioenerg. 40, 27–35 (2012)
Constantine, D., Wang, Y., Terrell, E.: Effect of reciprocation frequency on friction and wear of vibrating contacts lubricated with soybean-based B100 biodiesel. Tribol. Lett. 50, 279–285 (2013)
Xu, Y., Zheng, X., Hu, X., Dearn, K.D., Xu, H.: Effect of catalytic esterification on the friction and wear performance of bio-oil. Wear 311, 93–100 (2014)
Xu, Y., Hu, X., Yuan, K., Zhu, G., Wang, W.: Friction and wear behaviors of catalytic methylesterified bio-oil. Tribol. Int. 71, 168–174 (2014)
Xu, Y., Wang, Q., Hu, X., Li, C., Zhu, X.: Characterization of the lubricity of bio-oil/diesel fuel blends by high frequency reciprocating test rig. Energy 35, 283–287 (2010)
Bhuyan, S., Holden, L.S., Sundararajan, S., Andjelkovic, D., Larock, R.: Effect of crosslinking on the friction and wear behavior of soybean oil-based polymeric materials. Wear 263, 965–973 (2007)
Diomidis, N., Celis, J.P., Ponthiaux, P., Wenger, F.: Tribocorrosion of stainless steel in sulfuric acid: identification of corrosion–wear components and effect of contact area. Wear 269, 93–103 (2010)
Fan, X., Xia, Y., Wang, L., Pu, J., Chen, T., Zhang, H.: Study of the conductivity and tribological performance of ionic liquid and lithium greases. Tribol. Lett. 53, 281–291 (2014)
Yue, W., Gao, X., Wang, C., Li, X., Wang, S., Liu, J.: Synergistic effects between plasma-nitrided AISI 52100 steel and zinc dialkyldithiophosphate additive under boundary lubrication. Tribol. T 55, 278–287 (2012)
Wang, W., Gu, W., Liu, K., Wang, F., Tang, Z.: DEM simulation on the startup dynamic process of a plain journal bearing lubricated by granular media. Tribol. T 57, 198–205 (2013)
Dutta, S., Hartkopf-Fröder, C., Witte, K., Brocke, R., Mann, U.: Molecular characterization of fossil palynomorphs by transmission micro-FTIR spectroscopy: implications for hydrocarbon source evaluation. Int. J. Coal Geol. 115, 13–23 (2013)
Rabson, D.A.: Toward theories of friction and adhesion on quasicrystals. Prog. Surf. Sci. 87, 253–271 (2012)
Hu, K.H., Wang, J., Schraube, S., Xu, Y.F., Hu, X.G., Stengler, R.: Tribological properties of MoS2 nano-balls as filler in polyoxymethylene-based composite layer of three-layer self-lubrication bearing materials. Wear 266, 1198–1207 (2009)
Sasada, T., Oike, M., Emori, N.: The effect of abrasive grain size on the transition between abrasive and adhesive wear. Wear 97, 291–302 (1984)
Ren, X., Peng, Z., Hu, Y., Wang, C., Fu, Z., Yue, W., Qi, L., Miao, H.: Abrasive wear behavior of TiCN cermets under water-based slurries with different abrasives. Tribol. Int. 66, 35–43 (2013)
Schouwenaars, R., Jacobo, V.H., Ortiz, A.: Microstructural aspects of wear in soft tribological alloys. Wear 263, 727–735 (2007)
Mishra, S.P., Polycarpou, A.A.: Tribological studies of unpolished laser surface textures under starved lubrication conditions for use in air-conditioning and refrigeration compressors. Tribol. Int. 44, 1890–1901 (2011)
Ouyang, J.H., Sasaki, S.: The friction and wear characteristics of cathodic arc ion-plated (V, Ti)N coatings in sliding against alumina ball. Wear 257, 708–720 (2004)
Acknowledgments
The authors express their gratitude to Professor Liping Wang, Kunhong Hu, Xiaojun Sun, and Dr. Guangan Zhang for their assistance on the tribo-tests and discussion. The authors gratefully acknowledge the financial support given by the National Natural Science Foundation of China (51275143), the Anhui Provincial Natural Science Foundation (1408085ME82), and the College Students Innovation Experimental Plan Fund of HFUT.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Xu, Y., Zheng, X., Yin, Y. et al. Comparison and Analysis of the Influence of Test Conditions on the Tribological Properties of Emulsified Bio-Oil. Tribol Lett 55, 543–552 (2014). https://doi.org/10.1007/s11249-014-0384-2
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11249-014-0384-2