Skip to main content
Log in

The Laser Welding with Hot Wire of 316LN Thick Plate Applied on ITER Correction Coil Case

  • Original Research
  • Published:
Journal of Fusion Energy Aims and scope Submit manuscript

Abstract

ITER correction coil (CC) cases have characteristics of small cross section, large dimensions, and complex structure. The cases are made of heavy thick (20 mm), high strength and high toughness austenitic stainless steel 316LN. The multi-pass laser welding with hot wire technology is used for the case closure welding, due to its low heat input and deformation. In order to evaluate the reliability of this welding technology, 20 mm welding samples with the same groove structure and welding depth as the cases were welded. High purity argon was used as the shielding gas to prevent oxidation because of the narrowness and depth of the weld. In this paper investigation of, microstructure characteristics and mechanical properties of welded joints using optimized welding parameters are presented. The results show that the base metal, fusion metal, and heat affected zone (HAZ) are all have fully austenitic microstructure, and that the grain size of fusion metal was finer than that of the base metal. The welding resulted in an increase of hardness in the fusion metal and HAZ. It was confirmed that the tensile strength of fusion metal was higher than that of base metal and the impact toughness value is higher than industry standard requirement. Thus, this welding process was determined to be reliable for manufacture of the ITER CC cases manufacture.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10

Similar content being viewed by others

References

  1. Z. Zhou et al., Research on manufacture and enclosure welding of ITER correction coils cases. IEEE Trans. Appl. Supercond 22, 3 (2012)

    Google Scholar 

  2. H.C. Kim, K. Kim, Y.S. Lee, S.Y. Cho, H. Nakajima, Study on the weld characteristics of 316LN by magnetization measurement. J. Nuclear Mater. 386–388, 650–653 (2009)

    Article  Google Scholar 

  3. Tommi Jokinen et al., High power Nd:YAG laser welding in manufacturing of vacuum vessel of fusion reactor. Fusion Eng. Des. 69, 349–353 (2003)

    Article  Google Scholar 

  4. J.A. Brooks, M.I. Bakes, L.A. Boatner, Metall. Trans. 22A, 915 (1991)

    Article  Google Scholar 

  5. J.C Lippold, D.J Kotecki, Welding Metallurgy and Weldability of Stainless Steels (Wiley, Hoboken, 2005)

  6. V. Shankar, T.P.S. Gill, S.L. Mannan, S. Sundarlsan, Solidification cracking in austenitics stainless steel welds. Sadhana 28(2–4), 359–382 (2003)

    Article  Google Scholar 

  7. ITER Design Description Document, Magnets DDD 11 ITER_D_2N6NUK v1.13, 5. CC Coils and Structures. Sept 2009

  8. S.C. Tjong, S.M. Zhu, N.J. Ho, H.S. Ku, Microstructural characteristics and creep rupture behavior of electron beam and laser welded AISI 316L stainless steel. J. Nucl. Mater. 227, 24–31 (1995)

    Article  ADS  Google Scholar 

  9. Chinese industrial Standards NB/T 47014-2011, Welding procedure qualification for pressure equipment

Download references

Acknowledgments

The authors would like to acknowledge the ITER IO magnet division for their contribution to the definition of CC technical specification and development of task packages. We also thank Beijing University of Technology and SIASUN for their contributions on the equipment and welding technology of CC case.

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to Chao Fang.

Additional information

The views and opinions expressed herein do not necessarily reflect those of the ITER organization.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Fang, C., Song, Y., Wu, W. et al. The Laser Welding with Hot Wire of 316LN Thick Plate Applied on ITER Correction Coil Case. J Fusion Energ 33, 752–758 (2014). https://doi.org/10.1007/s10894-014-9745-y

Download citation

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10894-014-9745-y

Keywords

Navigation