Skip to main content
SpringerLink
Log in

Undrained Strength of Deposited Mine Tailings Beds: Effect of Water Content, Effective Stress and Time of Consolidation

  • Technical note
  • Published:
Geotechnical and Geological Engineering Aims and scope Submit manuscript

Abstract

An understanding of the geotechnical behaviour of mine tailings is imperative when evaluating the stability and erosional resistance of sedimented tailings beds; as well as for the design and long-term management of tailings disposal facilities. Laboratory testing was conducted on mine tailings beds of various ages and thicknesses, deposited from concentrated slurries. Measured index properties allowed classifying the tailings as a coarse grained and non-cohesive material. The results obtained from the performed sedimentation experiments showed that the primary consolidation of the tailings beds was complete in approximately 1 h and negligible volume changes occurred in the beds during secondary compression. The undrained shear strength of the tailings beds was measured using an automated fall cone device at a depth interval of 1 cm and a profile of the shear strength variation with depth was obtained. At each tested surface, moisture content specimens were taken to determine the moisture content profile of the tested tailings beds. The undrained shear strength of the beds varied between 0.008 and 0.975 kPa for effective stresses below 1.19 kPa and increased with depth. Correspondingly, the moisture content decreased with depth and varied between 17 and 27%. The factor controlling the undrained shear strength of the tested beds was the vertical effective stress, with the water content also having some secondary effect. The correlation between the undrained shear strength and the vertical effective stress was expressed with a second order polynomial function. Consolidation time did not appear to influence the observed shear strength.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10

Similar content being viewed by others

References

  • Adu-Wusu C, Yanful EK, Mian MH (2001) Field evidence of resuspension in a mine tailings pond. Can Geotech J 38:796–808

    Article  Google Scholar 

  • Alexis A, Le Bras G, Thomas P (2004) Experimental bench for study of settling-consolidation soil formation. Geotech Test J 27(6):557–567

    Google Scholar 

  • Azevedo RF, de Campos TM, Alves MCM, Villar LF (1994) Sedimentation and consolidation of a neutralized red mud. In: Macari EJ, Frost JD, Pumarada LF (eds) Geoenvironmental issues facing the Americas. American Society of Civil Engineers, New York, pp 111–114

    Google Scholar 

  • Been K, Sills GC (1981) Self-weight consolidation of soft soils: an experimental and theoretical study. Gèotechnique 31(4):519–535

    Article  Google Scholar 

  • Blight G, Bentel G (1983) The behaviour of mine tailings during hydraulic deposition. J S Afr Inst Min Metall 83(4):73–86

    Google Scholar 

  • Bowles JE (1986) Engineering properties of soils and their measurement, 3rd edn. McGraw-Hill Inc., USA, pp 70–71

    Google Scholar 

  • British Standards Institution, Standard BS 1377-2 (1990) Methods of test for soils for civil engineering purposes, part 2: classification tests. British Standards Institution, London

  • Bussière B (2007) Colloquium 2004: hydrogeotechnical properties of hard rock tailings from metal mines and emerging geoenvironmental disposal approaches. Can Geotech J 44:1019–1052

    Article  Google Scholar 

  • Canadian Standards Association and Bureau de normalisation du Quebec, Standard CAN/BNQ 2501-092 (2006) Soils—determination of liquid limit by the fall cone penetrometer and determination of plastic limit. Bureau de normalisation du Quebec, Quebec

  • Catalan LJ, Yanful EK (2002) Sediment-trap measurements of suspended mine tailings in shallow water cover. J Environ Eng 128(1):19–30

    Article  Google Scholar 

  • Chong YS, Ratkowsky DA, Epstein N (1979) Effect of particle shape on hindered settling in creeping flow. Powder Technol 23:55–66

    Article  Google Scholar 

  • Davies R (1968) The experimental study of the differential settling of particles in suspension at high concentrations. Powder Technol 2(1):43–51

    Article  Google Scholar 

  • Di Felice R, Parodi E (1996) Wall effects on the sedimentation velocity of suspensions in viscous flow. AlChE J 42(4):927–931

    Article  Google Scholar 

  • Elder DMcG, Sills GC (1985) Thickening and consolidation of sediment due to self weight. In: Moudgil BM, Somasundaran P (eds) Flocculation, sedimentation and consolidation. American Institute of Chemical Engineers, New York, pp 349–362

  • Farrell E (1997) ETC. 5 fall-cone study. Ground Eng 30(1):33–36

    Google Scholar 

  • Feng TW (2000) Fall-cone penetration and water content relationship of clays. Gèotechnique 50(2):181–187

    Article  Google Scholar 

  • Feng TW (2002) Discussion on “Persussin and cone methods of determining the liquid limit of soils” by A. Sridharan and K. Prakash. Geotech Test J 25(1):104–105

  • Hansbo S (1957) A new approach to determination of the shear strength of clay by the fall cone test. In: Proceedings of the Royal Swedish Geotechnical Institute, Stockholm, Sweden, Publication No. 14, pp 7–47

  • Holtz R, Kovacs W (1981) An introduction to geotechnical engineering. Prentice-Hall Inc., Englewood Cliffs, N.J. 07632, USA

  • Houlsby GT (1982) Theoretical analysis of the fall cone test. Gèotechnique 32(2):111–118

    Article  Google Scholar 

  • Imai G (1981) Experimental studies on sedimentation mechanism and sediment formation of clay materials. Soils Found 21(1):7–20

    Google Scholar 

  • Jeeravipoolvarn S, Scott JD, Chalaturnyk RJ (2009) 10 m standpipe tests on oil sand tailings: long-term experimental results and prediction. Can Geotech J 46:975–988

    Article  Google Scholar 

  • Komnitsas K, Bartzas G, Paspaliaris I (2004) Efficiency of limestone and red mud barriers: laboratory column studies. Miner Eng 17(2):183–194

    Article  Google Scholar 

  • Kynch GL (1952) A theory of sedimentation. Trans Faraday Soc 48:166–176

    Article  Google Scholar 

  • Leroueil S, Le Bihan JP (1996) Liquid limits and fall cones. Can Geotech J 33:793–798

    Article  Google Scholar 

  • McGregor RG, Blowes DW, Jambor JL, Robertson WD (1998) Mobilization and attenuation of heavy metals within a nickel mine tailings impoundment near Sudbury, Ontario, Canada. Environ Geol 36(3/4):305–319

    Article  Google Scholar 

  • Mehta AJ, Parchure TM, Dixit JG, Ariathurai R (1982) Resuspension potential of deposited cohesive sediment beds. In: Kennedy VS (ed) Estuarine comparisons. Academic Press, New York, pp 591–609

    Google Scholar 

  • Mehta AJ, Hayter EJ, Parker ER, Krone RB, Teeter AM (1989) Cohesive sediment transport. I: process description. J Hydraul Eng 115(8):1076–1093

    Google Scholar 

  • Mesri G (1975) Discussion of “New design procedure for stability of soft clays”. ASCE J Geotech Eng Div 101:409–412

    Google Scholar 

  • Mesri G (1989) A reevaluation of s u(mob) = 0.22σ p ′ using laboratory shear tests. Can Geotech J 26(1):163–164

    Article  Google Scholar 

  • Mesri G (2001) Undrained shear strength of soft clays from push cone penetration test. Gèotechnique 51(2):167–168

    Article  Google Scholar 

  • Mittal H, Morgenstern N (1975) Parameters for the design of tailings dams. Can Geotech J 12:235–261

    Article  Google Scholar 

  • Newson T, Fujiyasu Y, Fahey M (1996) A field study of the consolidation behaviour of saline gold tailings. Proceedings of 3rd international conference on tailings and mine waste. A. A. Balkema Publishers, Roterdam, pp 179–188

    Google Scholar 

  • Pane V, Schiffman RL (1985) A note on sedimentation and consolidation. Gèotechnique 35(1):69–72

    Article  Google Scholar 

  • Prachure TM, Mehta AJ (1985) Erosion of soft cohesive sediment deposits. ASCE J Hydraul Eng 111(10):1308–1326

    Article  Google Scholar 

  • Prakash K, Sridharan A (2006) Critical appraisal of the cone penetration method of determining soil plasticity. Can Geotech J 43:884–888

    Article  Google Scholar 

  • Qiu Y, Sego D (2001) Laboratory properties of mine tailings. Can Geotech J 38:183–190

    Article  Google Scholar 

  • Ranjan G, Rao A (2000) Basic and applied soil mechanics, 2nd edn. New Age International (P) Publishers, New Delhi

    Google Scholar 

  • Richardson JF, Zaki WN (1954) Sedimentation and fluidisation: part I. Trans Inst Chem Eng 32:82–100

    Google Scholar 

  • Samad MA, Yanful EK (2005) A design approach for selecting the optimum water cover depth for subaqueous disposal of sulphide mine tailings. Can Geotech J 42:207–228

    Article  Google Scholar 

  • Seneviratne N, Fahey M, Newson T, Fujiyasu Y (1996) Numerical modelling of consolidation and evaporation of slurried mine tailings. Int J Numer Anal Methods Geomech 20:647–671

    Article  Google Scholar 

  • Shamsai A, Pak A, Bateni S, Ayatollahi S (2007) Geotechnical characteristics of copper mine tailings: a case study. Geotech Geol Eng 25:591–602

    Article  Google Scholar 

  • Sharma B, Bora PK (2003) Plastic limit, liquid limit and undrained shear strength of soil—reappraisal. J Geotech Geoenviron Eng 129(8):774–777

    Article  Google Scholar 

  • Shaw SC, Groat LA, Jambor JL, Blowes DW, Hanton-Fong CJ, Stuparyk RA (1998) Mineralogical study of base metal tailings with various sulfide contents, oxidized in laboratory columns and field lysimeters. Environ Geol 33(2/3):209–217

    Article  Google Scholar 

  • Sridharan A, Prakash K (1999) Mechanisms controlling the undrained shear strength behaviour of clays. Can Geotech J 36(6):1030–1038

    Article  Google Scholar 

  • Sridharan A, Prakash K (2000) Percussion and cone methods of determining the liquid limits of soils: controlling mechanisms. Geotech Test J 23(2):236–244

    Article  Google Scholar 

  • Sridharan A, Prakash K (2003) Self weight consolidation: compressibility behaviour of segregated and homogeneous fine grained sediments. Mar Georesour Geotechnol 21:73–80

    Article  Google Scholar 

  • ASTM, Standard D 2487 (1997) Classification of soils for engineering purposes. Annual book of ASTM standards. American Society for Testing and Materials, Philadelphia

  • Swedish Standards Commission, Standard SS 027120 (1990) Geotechnical tests—cone liquid limit. Swedish Standards Commission, Stockholm

  • Terzaghi K (1942) Theoretical soil mechanics. Wiley, New York

    Google Scholar 

  • Tolhurst T, Black K, Paterson D, Mitchener H, Termaat G, Shayler S (2000) A comparison and measurement standardisation of four in situ devices for determining the erosion shear stress of intertidal sediments. Cont Shelf Res 20:1397–1418

    Article  Google Scholar 

  • Toorman EA (1996) Sedimentation and self-weight consolidation: general unifying theory. Géotechnique 46(1):103–113

    Article  Google Scholar 

  • Toorman EA (1999) Sedimentation and self-weight consolidation: constitutive equations and numerical modelling. Gèotechnique 49(6):709–726

    Article  Google Scholar 

  • Vick SG (1990) Planning, analysis, and design of tailings dams, 2nd edn. BiTech Publishers, Vancouver

    Google Scholar 

  • Volpe R (1979) Physical and engineering properties of copper tailings. Proceedings of current geotechnical practice in mine waste disposal. American Society of Civil Engineering, New York, pp 242–260

    Google Scholar 

  • Wasti Y, Bezirci MH (1985) Determination of the consistency limits of soils by the fall cone test. Can Geotech J 23:241–246

    Article  Google Scholar 

  • Wood DM, Wroth CP (1978) The use of cone penetrometer to determine the plastic limit of soils. Ground Eng 11(3):37

    Google Scholar 

  • Yanful EK, Verma A (1999) Oxidation of flooded mine tailings due to resuspension. Can Geotech J 36:826–845

    Article  Google Scholar 

  • Zreik DA, Ladd CC, Germaine JT (1995) A new fall cone device for measuring the undrained strength of vey weak cohesive soils. Geotech Test J 18(4):472–482

    Article  Google Scholar 

  • Zreik DA, Germaine JT, Ladd CC (1997) Undrained strength of ultra-weak cohesive soils: relationship between water content and effective stress. Soils Found 37(3):117–128

    Google Scholar 

  • Zreik DA, Germaine JT, Ladd CC (1998) Effect of aging and stress history on the undrained strength of ultra-weak cohesive soils. Soils Found 38(4):31–39

    Google Scholar 

Download references

Acknowledgments

This work was supported by research grant from the Natural Sciences and Engineering Research Council of Canada (NSERC).

Author information

Authors and Affiliations

  1. Department of Civil and Environmental Engineering, The University of Western Ontario, London, ON, N6A 5B9, Canada

    Rozalina S. Dimitrova & Ernest K. Yanful

Authors
  1. Rozalina S. Dimitrova
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Ernest K. Yanful
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Rozalina S. Dimitrova.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Dimitrova, R.S., Yanful, E.K. Undrained Strength of Deposited Mine Tailings Beds: Effect of Water Content, Effective Stress and Time of Consolidation. Geotech Geol Eng 29, 935–951 (2011). https://doi.org/10.1007/s10706-011-9428-7

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10706-011-9428-7

Keywords

Search

Navigation