Skip to main content
SpringerLink
Log in

Unsaturated and Saturated Flow Front Tracking in Liquid Composite Molding Processes using Dielectric Sensors

  • Published:
Applied Composite Materials Aims and scope Submit manuscript

Abstract

Liquid composite molding processes are manufacturing techniques involving the impregnation and saturation of dry fibrous preforms by means of injection or infusion of catalyzed resin systems. Complete wetting of the reinforcement and reduction of voids are key issues to enhance mechanical properties of the final product, as a consequence on line monitoring and control of resin flow is highly desirable to detect and avoid potentialbet macro- as well as micro-voids. In this paper, parallel-plate dielectric sensors were investigated to track the position of unsaturated as well as saturated flow fronts through dual scale porous media. Sensors configuration was analyzed and improved via electromagnetic (EM) finite element simulations. The effectiveness of the proposed system was assessed in one-dimensional impregnation tests. Good agreement was found between unsaturated front positions provided by the considered system and acquired through conventional visual techniques. An indirect verification strategy, based on CFD and EM simulations of the process, was applied to investigate the reliability of dielectric sensors with respect to saturation phenomena. Obtained outcomes highlighted the intriguing capabilities of the proposed method.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9

Similar content being viewed by others

References

  1. Mallick, P.K.: Composites Engineering Handbook. CRC Press, New York (1997)

    Google Scholar 

  2. Parnas, R.S.: Liquid Composite Molding. Hanser Gardner Pubns (2000)

  3. Vaidya, U.: Composites for Automotive, Truck and Mass Transit: Materials, Design, Manufacturing. DEStech Publications (2010)

  4. Hammami, A., Gebart, B.R.: Analysis of the vacuum infusion molding process. Polym. Compos. 21(1), 28–40 (2000)

    Article  Google Scholar 

  5. Karlsson, K.F., Åström, B.T.: Manufacturing and applications of structural sandwich components. Compos. Part A 28(2), 97–111 (1997)

    Article  Google Scholar 

  6. Varna, J., Joffe, R., Berglund, L.A.: Effect of voids on failure mechanisms in RTM laminates. Compos. Sci. Technol. 53(2), 241–249 (1995)

    Article  Google Scholar 

  7. Hernández, S., Sket, F., Molina-Aldareguì, J.M., González, C., LLorca, J.: Effect of curing cycle on void distribution and interlaminar shear strength in polymer-matrix composites. Compos. Sci. Technol. 71(10), 1331–1341 (2011)

    Article  Google Scholar 

  8. Zhou, F., Kuentzer, N., Simacek, P., Advani, S.G., Walsh, S.: Analytic characterization of the permeability of dual-scale fibrous porous media. Compos. Sci. Technol. 66(15), 2795–2803 (2006)

    Article  Google Scholar 

  9. Zhou, F., Alms, J., Advani, S.G.: A closed form solution for flow in dual scale fibrous porous media. Compos. Sci. Technol. 68(3–4), 699–70 (2008)

    Article  Google Scholar 

  10. Park, C.H., Lebel, A., Saouab, A., Bréard, J., Lee, W.I.: Modeling and simulation of voids and saturation in liquid composite. Compos. Part A 42(6), 658–668 (2011)

    Article  Google Scholar 

  11. Šimáček, P., Advani, S.G.: Desirable features in mold filling simulations for liquid composite molding processes. Polym. Compos. 25(4), 355–367 (2004)

    Article  Google Scholar 

  12. Gourichon, B., Binetruy, C., Krawczak, P.: A new numerical procedure to predict dynamic void content. Compos. Part A 37(11), 1961–1969 (2006)

    Article  Google Scholar 

  13. Modi, D., Correia, N., Johnson, M., Long, A., Rudd, C., Robitaille, F.: Active control of the vacuum infusion process. Compos. Part A 38(5), 1271–1287 (2007)

    Article  Google Scholar 

  14. Lawrence, J.M., Neacsu, V., Advani, S.G.: Modeling the impact of capillary pressure and air entrapment on fiber tow, saturation during resin infusion in LCM. Compos. Part A 40, 1053–1064 (2009)

    Article  Google Scholar 

  15. Simacek, P., Neacsu, V., Advani, S.G.: A phenomenological model for fiber tow saturation of dual scale fabrics in liquid composite molding. Polym. Compos. 31(11), 1881–1889 (2010)

    Article  Google Scholar 

  16. Vaidya, U.K., Jadhav, N.C., Hosur, M.V., Gillespie Jr., J.W., Fink, B.K.: Assessment of flow and cure monitoring using direct current and alternating current sensing in vacuum-assisted resin transfer molding. Smart Mater. Struct. 9, 727–736 (2000)

    Article  Google Scholar 

  17. Luthy, T., Ermanni, P.: Flow monitoring in liquid composite molding based on linear direct current sensing technique. Polym. Compos. 24(2), 249–262 (2003)

    Article  Google Scholar 

  18. Lim, S.T., Lee, W.I.: An analysis of the three-dimensional resin-transfer mold filling process. Compos. Sci. Technol. 60(7), 961–975 (2000)

    Article  Google Scholar 

  19. Lekakou, C., Cook, S., Deng, Y., Ang, T.W., Reed, G.T.: Optical fibre sensor for monitoring flow and resin curing in composites manufacturing. Compos. Part A 37(6), 934–938 (2006)

    Article  Google Scholar 

  20. Dunkers, J.P., Lenhart, J.L., Kueh, S.R., van Zanten, J.H., Advani, S.G., Parnas, R.S.: Fiber optic flow and cure sensing for liquid composite molding. Opt. Laser. Eng. 35(2), 91–104 (2001)

    Article  Google Scholar 

  21. Danisman, M., Tuncol, G., Kaynar, A., Sozer, E.M.: Monitoring of resin flow in the resin transfer molding (RTM) process using point-voltage sensors. Compos. Sci. Technol. 67(3–4), 367–379 (2007)

    Article  Google Scholar 

  22. Tuncol, G., Danisman, M., Kaynar, A., Sozer, E.M.: Constraints on monitoring resin flow in the resin transfer molding (RTM) process by using thermocouple sensors. Compos. Part A 38(5), 1363–1386 (2007)

    Article  Google Scholar 

  23. Schmachtenberg, E., Heide, S.Z.J., Topker, J.: Application of ultrasonics for the process control of Resin Transfer Moulding (RTM). Polym. Test. 24(3), 330–338 (2005)

    Article  Google Scholar 

  24. Skordos, A.A., Karkanas, P.I., Partridge, I.K.: A dielectric sensor for measuring flow in resin transfer moulding. Meas. Sci. Technol. 11, 25–31 (2000)

    Article  Google Scholar 

  25. Bang, K.G., Kwon, J.W., Lee, D.G., Lee, J.W.: Measurement of the degree of cure of glass fiber-epoxy comosites using dielectrometry. J. Mater. Process. Technol. 113(1–3), 209–214 (2001)

    Article  Google Scholar 

  26. Kim, H.G., Lee, D.G.: Dielectric cure monitoring for glass/polyester prepreg composites. Compos. Struct. 57(1–4), 91–99 (2002)

    Article  Google Scholar 

  27. Yenilmez, B., Sozer, E.M.: A grid of dielectric sensors to monitor mold filling and resin cure. Compos. Part A 40(4), 476–489 (2009)

    Article  Google Scholar 

  28. Carlone, P., Palazzo, G.S.: Flow monitoring and permeability measurements in LCM processes by the means of a dielectric sensor. Key Eng. Mater. 504–506, 289–294 (2012)

    Article  Google Scholar 

  29. ANSYS CFX 13.0 Reference Guide. ANSYS Inc (2010)

  30. De Parseval, Y., Pillai, K.M., Advani, S.G.: A simple model for the variation of permeability due to partial saturation in dual scale porous media. Transp. Porous Med. 27(3), 243–264 (1997)

    Article  Google Scholar 

  31. Walther, J., Simacek, P., Advani, S.G.: The effect of fabric and fiber tow shear on dual scale flow and fiber bundle saturation during liquid molding of textile composites. Int. J. Mater. Form. 5(1), 83–97 (2012)

    Article  Google Scholar 

  32. Tan, H., Pillai, K.M.: Multiscale modeling of unsaturated flow in dual-scale fiber preforms of liquid composite molding I: isothermal flows. Compos. Part A 43(1), 1–13 (2012)

    Article  Google Scholar 

  33. Bréard, J., Saouab, A., Bouquet, G.: Numerical simulation of void formation in LCM. Compos. Part A 34(6), 517–523 (2003)

    Article  Google Scholar 

  34. Gascons, M., Blanco, N., Simacek, P., Peiro, J., Advani, S., Matthys, K.: Impact of the fibre bed on resin viscosity in liquid composite moulding simulations. Appl. Compos. Mater. 19(3–4), 669–688 (2012)

    Article  Google Scholar 

  35. García, J.A., Gascón, L., Chinesta, F., Ruiz, E., Trochu, F.: An efficient solver of the saturation equation in liquid composite molding processes. Int. J. Mater. Form. 3(2), 1295–1302 (2010)

    Article  Google Scholar 

  36. Bayldon, J.M., Daniel, I.M.: Flow modeling of the VARTM process including progressive saturation effects. Compos. Part A 40(8), 1044–1052 (2009)

    Article  Google Scholar 

  37. Govignon, Q., Bickerton, S., Kelly, P.A.: Simulation of the reinforcement compaction and resin flow during the complete resin infusion process. Compos. Part A 41(1), 45–57 (2010)

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Department of Industrial Engineering, University of Salerno, Via Giovanni Paolo II 132, 84084, Fisciano, SA, Italy

    P. Carlone & G. S. Palazzo

Authors
  1. P. Carlone
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. G. S. Palazzo
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to P. Carlone.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Carlone, P., Palazzo, G.S. Unsaturated and Saturated Flow Front Tracking in Liquid Composite Molding Processes using Dielectric Sensors. Appl Compos Mater 22, 543–557 (2015). https://doi.org/10.1007/s10443-014-9422-3

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s10443-014-9422-3

Keywords

Search

Navigation