Abstract
Decreasing vibration amplitude during end milling process reduces tool wear and improves surface finish. Mathematical model has been developed to predict the acceleration amplitude of vibration in terms of machining parameters such as helix angle of cutting tool, spindle speed, feed rate, and axial and radial depth of cut. Central composite rotatable second-order response surface methodology was employed to create a mathematical model, and the adequacy of the model was verified using analysis of variance. The experiments were conducted on aluminum Al 6063 by high-speed steel end mill cutter, and acceleration amplitude was measured using FFT analyzer. The direct and interaction effect of the machining parameter with vibration amplitude were analyzed, which helped to select process parameter in order to reduce vibration, which ensures quality of milling.
Similar content being viewed by others
References
Hayajneh MT, Tahat MS, Bluhm J (2007) A study of the effects of machining parameters on the surface roughness in the end-milling process. Jordan Journal of Mechanical and Industrial Engineering 1(1):1–5
Suresh Kumar Reddy N, Venkateswara Rao P (2005) Selection of optimum tool geometry and cutting conditions using a surface roughness prediction model for end milling. Int J Adv Manuf Technol 26:1202–1210
Kang IS, Kim JS, Seo YW (2008) Cutting force model considering tool edge geometry for micro end milling process. J Mech Sci Technol 22:293–299
Zhang L, Zheng L (2005) Prediction of cutting forces in end milling of pockets. Int J Adv Manuf Technol 25:281–287
Routara BC, Bandyopadhyay A, Sahoo P (2009) Roughness modeling and optimization in CNC end milling using response surface method: effect of workpiece material variation. Int J Adv Manuf Technol 40:1166–1180
Palanisamy P, Rajendran I, Shanmugasundaram S (2008) Prediction of tool wear using regression and ANN models in end-milling operation. Int J Adv Manuf Technol 37:29–41
Li HZ, Zeng H, Chen XQ (2006) An experimental study of tool wear and cutting force variation in the end milling of Inconel 718 with coated carbide inserts. J Mater Process Technol 180:296–304
Maass P, Kuhfu B, Riemer O (2008) Mathematical models for surface characterization of machining processe. Microsyst Technol 14:1989–1993
Zatarain M, Bediaga I, Munoa J, Insperger T (2009) Analysis of directional factors in milling: importance of multi-frequency calculation and of the inclusion of the effect of the helix angle. Int J Adv Manuf Technol 47:535–542. doi:10.1007/s00170-009-2230-5
Chelladurai H, Jain VK, Vyas NS (2008) Development of a cutting tool condition monitoring system for high speed turning operation by vibration and strain analysis. Int J Adv Manuf Technol 37:471–485
Orhan S, Er AO, Camus-cu N, Aslan E (2007) Tool wear evaluation by vibration analysis during end milling of AISI D3 cold work tool steel with 35 HRC hardness. Elsevier NDT&E International 40:121–126
Weinert K, Kersting P, Surmann T, Biermann D (2008) Modeling regenerative workpiece vibrations in five-axis milling. Prod Eng Res Dev 2:255–260
Zhang JZ, Chen JC (2008) Tool condition monitoring in an end-milling operation based on the vibration signal collected through a microcontroller-based data acquisition system. Int J Adv Manuf Technol 39:118–128
Nakagawa H, Kurita Y, Ogawa K, Sugiyama Y, Hasegawa H (2008) Experimental analysis of chatter vibration in end-milling using laser Doppler vibrometers. Int J Automot Technol 2(6):431–438
Rahim IA, Miskam MA, Sidek O, Zaharudin SA, Mohd SKK (2009) Development of a vibration measuring unit using a microelectromechanical system accelerometer for machine condition monitoring. European Journal of Scientific Research 35(1):150–158, ISSN 1450-216X
Tansel I, Trujillo M, Nedbouyan A, Velez C, Wei-Yu Bao T, Arkan T, Tansel B (1998) Micro-end-milling—III. Wear estimation and tool breakage detection using acoustic emission signals. Int J Mach Tools Manuf 38:1449–1466
Balachandran B, Zhao MX (2000) A mechanics based model for study of dynamics of milling operations. Meccanica 35(89–109):2000
Tatar K, Gren P (2008) Measurement of milling tool vibrations during cutting using laser vibrometry. Int J Mach Tools Manuf 48(34):380–387
Kious M, Boudraa M, Ouahabi A, Serra R (2008) Influence of machining cycle of horizontal milling on the quality of cutting force measurement for the cutting tool wear monitoring. Prod Eng Res Dev 2:443–449
Stephenson DA, Agapiou JS (2006) Metal cutting theory and practice. Taylor & Francis, New York
Cochran WG, Cox GM (1963) Experimental design. Asia Publishing, India
Montgomery DC (1976) Design and analysis of experiments. Wiley, New York
Donaldson C, Lecain GH, Goold VC (1957) Tool design. Tata McGraw-Hill, New Delhi
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Sivasakthivel, P.S., Velmurugan, V. & Sudhakaran, R. Prediction of vibration amplitude from machining parameters by response surface methodology in end milling. Int J Adv Manuf Technol 53, 453–461 (2011). https://doi.org/10.1007/s00170-010-2872-3
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s00170-010-2872-3