Measurement and modeling of respirable particulate (PM10) and lead pollution over Madurai, India
- First Online:
- Cite this article as:
- Vijay Bhaskar, B., Jeba Rajasekhar, R.V., Muthusubramanian, P. et al. Air Qual Atmos Health (2008) 1: 45. doi:10.1007/s11869-008-0004-0
- 1.1k Downloads
Samples of particulate matter less than or equal to 10 μm (PM10) were collected round the clock duration by using a respirable dust sampler (APM 460 BL) in Madurai, the second largest and most densely populated city of Tamil Nadu, India. The Environmental Protection Agency (EPA)-recommended standard methods were adopted not only for sample collection but also for subsequent analysis of respirable particulate pollutants. The observed PM10 concentrations varied from 88.1 to 226.9 μg/m3, and lead concentrations ranged between 0.21 to 1.18 μg/m3. The annual averages of the concentrations of the pollutants of current concern manifested that they were mostly below the Indian air quality standards and were generally comparable with those concentrations observed in most other Indian urban areas. The AERMOD model was validated simultaneously by comparing the predicted levels with the estimated levels of PM10. The generated database of the present investigation on the degree of pollution may be used for further research investigation and pollution abatement in the city.
KeywordsUrban air pollutionMonitoringPM10PbAERMOD
It is well known that the health effects associated with the airborne particles are dependent on their toxicity. The extent to which air borne particles penetrate into the human respiratory system is mainly determined by the size of the penetrating particles (Balachandran et al. 2000). There are several epidemiological studies present in the literature (Dockery 1993; Hoek et al. 1997; Harrison and Yin 2000; Sammet et al. 2000), which have demonstrated a direct association between atmospheric inhalable particulate matter and respiratory diseases, pulmonary damage, and mortality especially in the urban areas. Therefore, the estimation of the levels of respirable particulate and its major toxic constituent lead (Pb) present in the urban atmosphere is a prime requirement of epidemiological investigation, air quality management, and air pollution abatement (Chow et al. 2002; Querol et al. 2001). For this purpose, we have monitored the levels of particulate matter less than or equal to 10 μm (PM10) and Pb. In addition, we have modeled the dispersion of PM10 over Madurai, the second largest city in the state of Tamil Nadu, India. The measurements (sample collection) and chemical analysis were made using the standard method recommended by the Environmental Protection Agency (EPA), USA, for the period of 1 year viz. July 2005 to June 2006. To investigate the dispersion of pollutants over Madurai city, we have used AERMOD model (EPA 2005; Cimorelli et al. 2005; Kesarkar et al. 2007) developed by EPA. The results obtained from the monitoring of PM10 and Pb along with modeling of PM10 is presented in this investigation.
This paper is organized as follows. “Details of the experiments” of this paper presents the details of the monitoring of PM10 and Pb over Madurai city. The results of monitoring and modeling of PM10 dispersion using AERMOD, a steady-state plume dispersion model, are discussed in “Results and discussions.” The major conclusions are presented in “Conclusions.”
Details of the experiments
Monitoring of respirable particulate matter
Madurai city (9°54′ N, 78°84′ E and 100 m above sea level), popularly known as the City of Temples, has an important historical, cultural, and religious heritage in South India. This city has a surface area of 52.8 km2 with an estimated population of 1.2 million in 2001 (Jeba Rajasekhar et al. 2004). The ambient air quality of the city is greatly affected due to combustion of fossil fuels in stationary and mobile sources, and it was observed that the rate of combustion of fossil fuels had an increasing trend over the decades. To study the distribution of pollutants over Madurai city, the measurements of respirable particulate matter and Pb were carried out at six different sampling sites. The selections of these sites were made based on the existing anthropogenic activities occurring at these sites, which were responsible for atmospheric pollution. These anthropogenic activities included the varying density of road traffic, industrialization, and domestic activities within the urban limits of the city. The air samples were collected periodically for 1 year to estimate the concentrations of the particulate pollutants of current concern.
A description of the land use and likely sources of atmospheric pollution in the vicinity of the sites is given below.
Periyar bus stand
This is the main bus station situated at the heart of the city. The area of this bus station is very limited, and it is surrounded by narrow roads. Therefore, at this site, there are always traffic jams and congestion leading to slow movement of traffic. The contribution to air pollution at this site is mainly due to the emissions from public and commercial transportation (buses, trucks, autorickshaws, and two-wheelers). The accumulation of the air pollutants may be endured at this site due to the presence of tall roadside shops, houses, and buildings.
This is a very busy commercial site located in the northern part of the city. A large number of shops, restaurants, and workshops, in addition to some Government establishments such as Government Rajaji Hospital (the biggest hospital in the southern Tamil Nadu region), colleges, and schools, are situated near this site. Although the roads are relatively wider than those at the central parts of the city, the movement of the traffic is highly congested and slow due to high density of vehicles and encroachment on the road sides.
This site is surrounded by many cottages and small-scale industries mostly related to furniture, grill works, plastic, and rubber and also by lathe works, electroplating units, rice mills, and residential colonies. The continuous traffic flow witnessed at this site is due to the bus station located near by. Besides the emissions from automobiles, the emissions from commercial and domestic sectors contribute to the total air pollution load at this sampling site.
This is an industrial site of Madurai city, where two major coal-based rubber industries that produce rubber-based domestic appliances are situated. The National Highway (NH-47) Extension passing near this site has a substantial flow of traffic. Hence, the emissions from the industries and automobiles are the major sources of air pollution in this region. At this site, there are also some residential colonies of high-profile people.
Pudur is a fast emerging extension area of the city with many residential colonies. There are also a number of Government offices, educational institutions, and commercial establishments in this area of study. Traffic flow consists mainly of light-tonnage vehicles especially two-wheelers and heavy-tonnage vehicles mainly the public buses. Since the roads are narrow and their conditions are poor, traffic emissions are substantial. An industrial estate that consists of small-scale industries including electroplating and welding units is situated in the outskirts of Pudur, which may also contribute by means of background concentrations.
Sree Meenakshi temple
Having a large number of temples, Madurai is popularly referred as the temple city of south India. Sree Meenakshi temple, the landmark of the city, is located at the central part of the city. Around the temple, there are many commercial establishments. This causes the site to be very crowded with continuous traffic flow almost round the clock. The emissions from automobiles, commercial establishments, and residences contribute to the air pollution loads of this sampling site.
Topographical features of Madurai
The topography of the Madurai city very slightly increases in all directions as one moves away from the heart of the city except in the south direction, and this city is surrounded by the gently sloping terrain. There are no hills in the region of the Madurai Corporation limit. Therefore, the existing topography of this city experiences horizontally homogeneous wind flow and more or less steady-state meteorological conditions. Such conditions do not allow the accumulation of pollutants (Benson 1989). However, for the central regions of this city, building geometry on both sides of the narrow roads is an important parameter for characterizing the transport and dispersion of pollutants. This geometry can be treated as a tunnel, which is open at the top, and this is commonly referred as street canyon. The elevated pollutant concentrations at some of the sampling sites, which are located in the central parts of the city, may also be determined by this parameter (Copper and Alley 1986; Buckland and Middleton 1999).
Measurement of PM10 sampling
The PM10 samples were collected round the clock duration by using commercially available Respirable Dust Sampler (Envirotech APM 460BL). The sampler had a free-flow condition without filter, and the flow rate of air sampler varied between 0.9 and 1.4 m3/min. It could be operated up to 28 h. Whatmann microfiber filter papers (EPM 2000) were used for the collection of PM10 particles. The glass fiber filter of the dimensions 8 × 10 in. was used for this measurement in such a way that a 7 × 9-in. area of the filter was exposed on the respirable dust sampler. The centrifugal force method was adopted to remove the large particles. Continuous and simultaneous samplings were carried out at all the sites for a period of 1 year viz. July 2005 to June 2006. The ground level meteorological conditions required for air quality modeling viz. temperature, wind speed, wind direction, solar radiation, rainfall, and relative humidity were collected simultaneously on a 30-min basis during sampling of PM10 for the period of July 2005 to June 2006.
Chemical analysis of PM10 measurements
For this study, airborne PM10 concentrations were determined gravimetrically using a system of filter papers. Filters used for PM10 particle collection were dried, before and after the weighing, in the high-volume desiccator under 5% relative humidity for 48 h. Experiments of conservation, drying, and weighing were conducted in the dark room with relative humidity of 50 ± 5% and temperature of 20 ± 1°C. The exposed filter paper was cut into 4 × 5-cm strips. The strips for the metal analysis were ashed in a low-temperature asher, and the ashed filter was then placed in a glass tube, which was treated with 10 ml nitric acid, 5 ml hydrochloric acid, and 5 ml perchloric acid and warmed for 5 h. To complete the digestion process, the digestion was done three times, and the sample was evaporated to dryness. The sample residues were dissolved in 1% nitric acid, cooled, and made up to 50 ml in a volumetric flask with the help of double-distilled dematerialized water. Following the dilution, the samples were centrifuged at 2,000 rpm for about 30 min, and the supernatant liquid was decanted into polypropylene tubes that were then capped and stored for pending analysis (Katz 1969; Tripathi 1994).
A blank filter paper was also similarly digested, and the same procedure was carried out. The analysis was subsequently made by atomic absorption spectroscopy (AAS). A commercially available AAS (Varian Spectra 220) was used to estimate the concentrations, which were calculated by comparing the absorbance of sample solutions with the standard metal solutions. The standard solutions for the metals under investigations were prepared from the stack solutions just before their utilization.
Meteorology plays a crucial role in air pollution studies. In fact, there is a strong seasonality in the meteorological factors, which modulates the air quality levels (Espinosa et al. 2004; Karar et al. 2005). The important meteorological variables having influence on the levels of the pollutants over Madurai are wind (speed and direction), rain (amount and duration), air temperature, and relative humidity (Singal and Prasad 2005). The analysis of the meteorological observations during the period of July 2005 to June 2006 showed the maximum solar radiation of 1,024 w/m2, and the highest atmospheric temperature of 44.8°C was recorded during the summer season (March–May). It was observed that the velocity of wind was maximum during the months of July (8.4), followed by August (6.8) and September (5.5) and ranged between 0.3 and 8.4 m/s. The predominant wind velocity was observed in the northeast monsoon season. In the summer months, the observed wind speed was relatively lower than those in the winter season and varied from 0.2 to 6.2 m/s. The predominant wind directions during the period of this study were northeast, east, southeast, and west. The maximum number of rainy days (41) and the average maximum rainfall (501 mm) took place in the month of October followed by November due to presence of the northeast monsoon. The variation of relative humidity showed a steep decrease from winter to summer (66% to 57%) and then a slow increase in the rainy season (67% to 78%) and remained steady in winter (68%).
Results and discussions
Summary of PM10 concentrations at six sites of Madurai city
PM10 concentration (μg/m3)
Summary of Pb concentrations at six sites of Madurai city
Pb concentration (μg/m3)
Multiple regression coefficients for PM10 pollutant
Multiple regression coefficients for Pb pollutant
Seasonal variations of PM10 concentrations in Madurai city
PM10 seasonal concentrations (μg/m3)
146.1 (CV = 10%)
130.2 (CV = 9.2%)
147.5 (CV = 8.9%)
187.8 (CV = 8.0%)
163.2 (CV = 20.1%)
149.3 (CV = 15.8%)
152.3 (CV = 18.1%)
202.4 (CV = 7.6%)
135.3 (CV = 6.1%)
115.8 (CV = 6.6%)
128.5 (CV = 13.7%)
137.9 (CV = 5.7%)
126.0 (CV = 4.1%)
119.8 (CV = 7.9%)
126.0 (CV = 8.4%)
139.4 (CV = 5.1%)
116.5 (CV = 9.1%)
102.9 (CV = 10.2%)
109.4 (CV = 13.9%)
133.4 (CV = 6.8%)
89.0 (CV = 14.8%)
79.8 (CV = 4.6%)
96.3 (CV = 19.0%)
123.8 (CV = 17.5%)
Seasonal variations of Pb concentrations in Madurai city
Seasonal concentrations (μg/m3)
0.92 (CV = 7.6%)
0.76 (CV = 10.0%)
0.80 (CV = 16.0%)
0.90 (CV = 13.8%)
0.70 (CV = 12.0%)
0.87 (CV = 13.5%)
0.92 (CV = 6.0%)
0.93 (CV = 18.0%)
0.56 (CV = 13.5%)
0.43 (CV = 16.1%)
0.48 (CV = 16.9%)
0.55 (CV = 10.6%)
0.49 (CV = 8.7%)
0.49 (CV = 13.3%)
0.48 (CV = 12.5%)
0.49 (CV = 13.0%)
0.51 (CV = 5.3%)
0.45 (CV = 17.0%)
0.47 (CV = 17.2%)
0.51 (CV = 17.9%)
0.44 (CV = 9.2%)
0.39 (CV = 15.2%)
0.39 (CV = 13.4%)
0.45 (CV = 21.9%)
Automobile source strength of particulate pollutants
PM emissions (10−3 g m−1 s−1)
Pb emissions (10−3 g m−1 s−1)
West Tower street
West Masi street
North Masi street
East Masi street
South Masi street
East Veli street
Anna bus stand
Modeling of air quality
AERMOD is a steady-state plume dispersion model for the assessment of pollutant concentrations from a variety of sources (EPA 2005; Cimorelli et al. 2005; Kesarkar et al. 2007). AERMOD has an improved approach for characterizing the fundamental boundary layer parameters and vertical profile of the atmosphere along with better representation of plume buoyancy, penetration, and urban nighttime boundary layer (Cimorelli et al. 2005) as compared to the industrial source complex (ISC) model. It provides variable urban treatment of vertical dispersion as a function of city population and can selectively model sources as rural or urban. AERMOD requires hourly surface and upper air meteorological observations for simulating the pollutant dispersion. AERMOD simulates transport and dispersion from multiple points, area, or volume sources based on an up-to-date characterization of the atmospheric boundary layer. Sources may be located in the rural or urban areas, and receptors may be located in simple or complex terrain. AERMOD also accounts for building wake effects (i.e., plume downwash). The model employs hourly sequential preprocessed meteorological data to estimate concentrations for averaging times from 1 h to 1 year (EPA 2004). This model assumes the probability distribution function for the concentration of a pollutant to be Gaussian both in the vertical as well as horizontal directions in a stable boundary layer. In the convective boundary layer, the horizontal dispersion is Gaussian, whereas the vertical distribution is represented by a bi-Gaussian probability distribution function. The vertical distribution required meteorological variables that are generated based on meteorological observations using a similarity relationship. The AERMOD model has a AERMET processor to calculate planetary boundary layer parameters viz. friction velocity, Monin–Obukhov length, convective velocity scale, temperature scale, mixing height, surface heat flux by using local surface characteristics in the form of surface roughness, and Bowen ratio in combination with standard meteorological observations (wind speed, wind direction, temperature, and cloud cover). Then, these parameters are used to calculate vertical profiles of wind speed, lateral and vertical turbulent fluctuations, and the potential temperature gradient in AERMOD. This model is intended to be useful for the simulation of short-range (<50 km) pollutant dispersion.
In these equations, plume dilution and plume spread are calculated using effective boundary layer variables. In fact, hp is the plume height, σy and σz are plume dispersion parameters, and ha is the level where vertical mixing is limited (=max (hp, h)) where h is the stable (mechanical) mixed layer height and hp is equal to the stack height plus plume rise (Δh).
In fact, hedi and σzdj are the effective source height and vertical dispersion parameter, and σb is the dispersion due to buoyancy-induced entrainment. Equation 5 is the general expression for the concentration distribution along the plume center line. By providing the required inputs like emission and meteorological factors, the concentrations for the pollutants at all the sampling stations of the present investigation were predicted by using the AERMOD model.
The emissions of particulate matter in the study area are characterized by anthropogenic sources like transportation, industries, and domestic activities. There are two major industries that produce rubber-based domestic and commercial appliances. The domestic activities mainly include burning of fuels like liquefied petroleum gas, kerosene, fuel wood, and agricultural residues. To generate an emission inventory, a traffic survey was conducted by the physical counting of automobiles round the clock all over the city including the sampling stations of the present investigation. In fact, the study area was divided into a number of square grids of 1 km dimension. The total kilometer run for each grid was developed by using the data on number of vehicles and road lengths. The automobile source strength was calculated subsequently by using the total kilometer run by the vehicles and the emission rate of Indian vehicles.
The calculated automobile source strengths with special reference to particulate matter and lead all over the city showed that they ranged from 51.84 × 10−3 to 410.64 × 10−3 and from 1.42 × 10−3 to 12.36 × 10−3 g m−1 s−1, respectively. In the case of particulate matter emissions, it was noted that the heavy-tonnage vehicles had relatively higher emission rates than the medium-tonnage vehicles. The two- and three-wheelers also contributed notably (more than 70% at many traffic areas) in the total lead load of Madurai city. Even though the lead emission factor (g/km) for two- and three-wheelers is relatively lower in comparison with medium-tonnage vehicles, their contribution was about three to five times greater, which was due to the operation of a large number of motorized two- and three-wheelers (Pundir et al. 1994; Sivacoumar 1990). The automobile-based emission inventory was prepared, and it was used to initialize the AERMOD model. The emission inventory was generated for the sampling period only. However, the annual emission inventory by our team for both stationary and mobile sources is being generated for further research studies.
In general, transportation, small-scale industries, and an elevated rate of combustion of conventional fuels for domestic and commercial purposes in the city are found to be the sources of particulate pollutants of the present investigation (Kulandai 2003; Adachi and Tainosho 2004). Except automobiles, the operation of diesel-powered generators (which were used in commercial establishments during power failures especially at summer seasons), emissions from paved roads, and background concentrations from industrial and semi-industrial areas of the city also contribute to particulate pollution. Cooking in houses, school and commercial establishments, and refuse incineration in houses and public places and municipal incineration in open grounds may also contribute to the total pollutant load as well as the atmospheric particulate matter concentrations in an Indian city (Surya Prakash and Alappat 1999; Salve et al. 2006). The sand along the sides of the roads, which is dusty in nature, is not removed periodically all over the city. Hence, all these factors cumulatively contribute to the PM10 concentrations in the range of 88.1 to 226.9 μg/m3 in the city. Madurai is surrounded by agricultural lands, and so no potential sources are available in the vicinities of the city or from upwind sites.
Even though the PM10 pollution activities were widespread all over the city, it was noticed that during the period of experiment, Goripalayam endured the highest traffic densities among the sampling stations. The highest average concentrations of PM10 and lead at Goripalayam might be attributed to the pollution from automobiles. In fact, at this place, there were a large number of light-tonnage vehicles, especially motorized two-wheelers (62,145), in the operation. Extreme congestion (resulting the slow movement of vehicles and random urban driving modes of operation), long waits at the signals, and traffic bottlenecks are observed commonly during the peak hours of traffic, as this site connects almost all the northern parts of the city (Tripathi et al. 2000; Katiyar et al. 2005). In addition, traffic-derived aerosol particles were emitted into the atmosphere due to abrasion processes of automobile components such as the brake or tire wear (Viana et al. 2006). Therefore, the emissions and abrasion of the components of automobiles might be the major contributors to the mass of total particles along with emissions from some small-scale industrial sources (Harrison et al. 2004). Traffic diversions from other parts of the city along the roads of this sampling station might be correlated with the maximum standard deviation that endured at Goripalayam.
The lowest concentrations of PM10 and lead were recorded at Sree Meenakshi temple sampling station, which could be considered as a sensitive area with the lowest traffic densities among the sampling stations. As the roads around this temple are one-way roads, the traffic density was very limited. In addition, there was restriction for the flow of heavy-tonnage vehicles in this area. The traffic survey results showed that at this site, a low number of automobiles were plying. Most of the vehicles that are operated in this area are gasoline-powered light-duty vehicles, which emitted almost negligible amount of particulates (Pundir et al. 1994; Jeba Rajasekhar et al. 2005; Gertler et al. 2006). The elevated buildings could restrict the background concentrations from the nearby semi-industrialized areas. It was also noted that among the commercial establishments, only a few are related to combustion activities. As the number of sources was substantially less, the calculated source strengths of particulate matter as well as the recorded concentrations of PM10 were also found to be low.
The experimental investigation on air pollution with special reference to average particulate pollutants revealed that the pollutants PM10 and Pb over Madurai were near to the permissible limits at all the sampling sites during most of the times of the year. It is worth mentioning here that PM10 has the permissible limits (for 24 h) of 150, 100, and 75 μg/m3 for the industrial and mixed, residential and rural, and sensitive areas, respectively, whereas Pb has the permissible limits of 1.5, 1.0, and 0.75 μg/m3 for the industrial and mixed, residential and rural, and sensitive areas, respectively. However, PM10 has permissible limits (annual averages) of 120, 60, and 50 μg/m3 for the industrial and mixed, residential and rural, and sensitive areas, respectively, whereas Pb has the permissible limits of 1.0, 0.75, and 0.50 μg/m3 for the industrial and mixed, residential and rural, and sensitive areas, respectively. It was anticipated that with increase in the population, traffic, industrialization, and per capita energy consumption in the future might increase the emission load, which in turn will deteriorate the quality of the air more over Madurai. The increases in the atmospheric pollutant with this rate have created a threat for long-range adverse effects on the public health and social wellbeing of this city. The earlier studies pertaining to particulate pollution shows that the concentration of particulate pollutants shows an upward trend during the years. Therefore, the strict implementation of adequate abatement measures and environmental regulations are necessary for the pleasant present and the sustainable future. The AERMOD model under predicts patterns of PM10 by a factor of 1–1.5 in the concentrations. Hence, monitoring of PM10 concentration in the city over a longer period coupled with inclusive emission inventories for additional stationary sources are needed.